Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM › from 2016.01
RM3250E _58 Vehicle Interior _038065 THEFT DETERRENT / KEYLESS ENTRY _0184917 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Theft Warning Siren Circuit  


DESCRIPTION

The theft warning siren assembly has an internal battery. If the vehicle battery cable is disconnected or any of the communication lines are open, the theft warning siren assembly detects this and sounds its siren.

Although the theft warning siren assembly usually sounds by receiving a signal from the body ECU, the theft warning siren assembly can sound by its internal battery in case the vehicle battery cable is disconnected.

The body ECU sends an arming signal to the theft warning siren assembly while transferring to the armed state, and it also sends a disarming signal to the siren while switching to the disarmed state. Also, the body ECU can cause the theft warning siren assembly to sound by sending an alarm signal during the alarm sounding state.

WIRING DIAGRAM

B413966E06
5.583,2.896 6.813,3.094 1.229,0.198 10 false G28 5.594,3.073 6.823,3.271 1.229,0.198 10 false Body ECU 5.635,1.74 6.865,1.938 1.229,0.198 10 false SSCL 5.344,1.615 6.573,1.813 1.229,0.198 10 false 11 3.927,1.625 5.156,1.823 1.229,0.198 10 false 2 3.448,1.76 4.677,1.958 1.229,0.198 10 false CONT 3.563,1.25 4.792,1.448 1.229,0.198 10 false +B 3.917,1.146 5.146,1.344 1.229,0.198 10 false 3 1.167,1.615 2.396,1.813 1.229,0.198 10 false 1 1.417,1.74 2.646,1.938 1.229,0.198 10 false GND 1.542,2.656 2.771,2.854 1.229,0.198 10 false N16 1.542,2.833 3.74,3.146 2.198,0.313 10 false Theft Warning Siren Assembly 1.698,0.271 2.927,0.469 1.229,0.198 10 false from Battery 3.656,0.438 4.885,0.635 1.229,0.198 10 false S-HORN

CAUTION / NOTICE / HINT

NOTICE:
·

If the theft warning siren assembly is replaced, refer to the Service Bulletin.

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

w/ Door Control Battery:

As the door control battery is installed between the vehicle battery and body ECU, first perform the inspections to confirm that there are no malfunctions in the power source circuit for the body ECU before performing this troubleshooting procedure.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>PRECAUTION

·

w/ Automatic Light Control System:

If the body ECU has been replaced, it is necessary to initialize the body ECU.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (THEFT WARNING SIREN ASSEMBLY - BATTERY AND BODY GROUND)
a.
B412630C08
1.354,0.104 1.896,0.406 0.542,0.302 0.781,1.74 0.938,1.74 0.938,1.74 1.313,1.219 true 2.479,1.76 2.271,1.76 2.271,1.76 1.948,1.219 true 0.146,0.094 0.458,0.292 0.313,0.198 10 false *a 1.5,0.177 1.813,0.375 0.313,0.198 10 false N16 0.417,1.656 0.729,1.854 0.313,0.198 10 false GND 2.542,1.667 2.854,1.865 0.313,0.198 10 false +B
*a Front view of wire harness connector
(to Theft Warning Siren Assembly)


Disconnect the theft warning siren assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
N16-3 (+B) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N16-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (THEFT WARNING SIREN ASSEMBLY - BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (THEFT WARNING SIREN ASSEMBLY - BODY ECU)
a.

Disconnect the N16 theft warning siren assembly connector.


b.

Disconnect the G28 body ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N16-2 (CONT) - G28-11 (SSCL) Always Below 1 Ω
N16-2 (CONT) - Body ground Always 10 kΩ or higher
G28-11 (SSCL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK THEFT WARNING SIREN ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK THEFT WARNING SIREN ASSEMBLY
a.

Temporarily replace the theft warning siren assembly with a new or normally functioning one.

HINT:

Refer to the Service Bulletin.



b.

Check the operation of the theft warning siren assembly function.

OK:

Theft warning siren assembly function operates normally.



Result:
Proceed to
OK
NG (for LHD)
NG (for RHD)



OK

END (THEFT WARNING SIREN ASSEMBLY WAS DEFECTIVE)

NG (for LHD)

NG (for RHD)