Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR › 2016.01–2016.03
RM3250E _59 Vehicle Exterior _038077 DOOR / HATCH _0186366 FRONT DOOR A

DOOR / HATCH  FRONT DOOR  DISASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.

·

Use the same procedure for RHD and LHD vehicles.

·

The procedures listed below are for LHD vehicles.

·

Fully open the front door glass sub-assembly LH before proceeding with work.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
w/ Curtain Shield Airbag:
B394719

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
w/ Curtain Shield Airbag:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 67492A 3.REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH

a.

Detach the clip and claw and remove the front door lower frame bracket garnish LH.

B412062C01
0.094,0.135 0.354,0.354 0.26,0.219 10 true *A 3.781,0.146 4.042,0.365 0.26,0.219 10 true *B
*A w/ Front No. 2 Speaker *B w/o Front No. 2 Speaker



Hide 74220 4.REMOVE FRONT ARMREST ASSEMBLY LH

a.
B412063C01
0,0 0,0 false
V113146

Place Hands Here
V100135

Order of Removal
V113147

Remove in this Direction


for Single Cab, Smart Cab:

Detach the clip and claw and remove the front armrest assembly LH as shown in the illustration.


b.
B412064C01
0,0 0,0 false
V113146

Place Hands Here
V100135

Order of Removal
V113147

Remove in this Direction


for Double Cab:

Detach the clip and claw and remove the front armrest assembly LH as shown in the illustration.


Hide 5.REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side, w/ Power Window)

a.
B412065C01
0.052,0.073 0.271,0.302 0.219,0.229 10 true *A 0.052,2.281 0.365,2.479 0.313,0.198 10 true *B
*A for Single Cab, Smart Cab
*B for Double Cab
V113147

Remove in this Direction


Detach the clip and claw.


b.

Disconnect each connector and remove the power window regulator master switch assembly with front door armrest base panel.


Hide 84870A 6.REMOVE OUTER MIRROR SWITCH ASSEMBLY (for Driver Side, w/ Power Window)

Hide 84820 7.REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (for Driver Side, w/ Power Window)

a.

for Models with Jam Protection Function on Driver Door Window Only:

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL


b.

except Models with Jam Protection Function on Driver Door Window Only:

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL


Hide 8.REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side, w/ Power Window)

a.
B412066C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the clip and claw.


b.

Disconnect the connector and remove the power window regulator switch assembly with front door armrest base panel.


Hide 84810 9.REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Front Passenger Side, w/ Power Window)

Hide 69260 10.REMOVE FRONT DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)

a.
B412067C01
0,0 0,0 false
V100155

Protective Tape
V113147

Remove in this Direction


Insert a clip remover between the plate and front door trim board.

HINT:

Tape the clip remover tip before use.



b.

Turn the handle clockwise to remove the snap ring, front door window regulator handle assembly and plate.


Hide 67666B 11.REMOVE FRONT DOOR TRIM REFLECTOR LH (w/ Reflex Reflector Assembly)

a.
B412068C03
0.073,0.052 0.385,0.25 0.313,0.198 10 true *A 0.094,2.313 0.406,2.51 0.313,0.198 10 true *B
*A for LH side
*B for RH side
V100155

Protective Tape
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Put protective tape around the reflex reflector.


b.

Using a thin-bladed screwdriver, detach the claw and guide.

HINT:

Tape the thin-bladed screwdriver tip before use.



c.

Remove the front door trim reflector LH.


Hide 69284C 12.REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG LH

a.
B412069

Using moulding remover A, detach the claw and remove the front door inside handle bezel plug LH as shown in the illustration.


Hide 67602 13.REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

a.
B412070

Remove the 3 screws.


b.

Detach the clip as shown in the illustration.

B412071C01
0.094,0.073 0.323,0.26 0.229,0.188 10 true *A 3.833,0.094 4.063,0.281 0.229,0.188 10 true *B
*A for Single Cab, Smart Cab *B for Double Cab
V113146

Place Hands Here - -
V100135

Order of Removal (1)
V100136

Order of Removal (2)
V113147

Remove in this Direction - -



c.
B412072C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the guide and remove the front door trim board sub-assembly LH as shown in the illustration.


d.
B412073C01
2.552,0.917 2.552,0.438 2.552,0.438 2.042,0.438 true 2.552,1.385 2.552,1.833 2.552,1.833 2.167,1.833 true 1.917,0.365 2.156,0.594 0.24,0.229 10 true *1 2.021,1.74 2.219,1.958 0.198,0.219 10 true *2
*1 Front Door Inside Looking Cable Assembly LH
*2 Front Door Lock Remote Control Cable Assembly LH
V113147

Remove in this Direction


Detach the clamp and disconnect the front door lock remote control cable assembly LH and front door inside looking cable assembly LH as shown in the illustration.


Hide 69206B 14.REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY LH

a.
B412074C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the claw and guide and remove the front door inside handle sub-assembly LH from the front door trim board sub-assembly LH.


Hide 68172A 15.REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP LH

a.

Raise the claw of the front door inner glass weatherstrip LH as shown in the illustration, and then remove the front door inner glass weatherstrip LH from the front door trim board sub-assembly LH.

B412075C01
0.115,0.083 0.427,0.281 0.313,0.198 10 false *A 3.854,0.083 4.167,0.281 0.313,0.198 10 false *B
*A for Single Cab, Smart Cab *B for Double Cab



Hide 86160 16.REMOVE FRONT NO. 1 SPEAKER ASSEMBLY

Hide 86160P 17.REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (w/ Front No. 2 Speaker)

Hide 89835 18.REMOVE DOOR SIDE AIR BAG SENSOR LH (w/ Curtain Shield Airbag)

Hide 87940 19.REMOVE OUTER REAR VIEW MIRROR ASSEMBLY LH

Hide 67832 20.REMOVE FRONT DOOR SERVICE HOLE COVER LH

a.
B412076C01
0,0 0,0 false
V100143

Butyl Tape


w/ Curtain Shield Airbag:

Remove the ground bolt and disconnect the ground wire.


b.

w/ Power Mirror Control System:

Detach the clamp.


c.

Detach the clamp.


d.

Pull out the front door lock remote control cable assembly LH, front door inside locking cable assembly LH and wire harness from the front door service hole cover LH, and then remove the front door service hole cover LH.

NOTICE:

Remove any remaining butyl tape from the front door panel.



Hide 21.REMOVE SCREW GROMMET

a.
B412077

Using a clip remover, detach the claw and remove the 2 screw grommets.


Hide 68151C 22.REMOVE FRONT DOOR GLASS RUN LH

a.
B412078

for Single Cab, Smart Cab:

Detach the guide and remove the front door glass run LH.


b.
B412078

for Double Cab:

Detach the guide and remove the front door glass run LH.


Hide 68102 23.REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH

a.

w/ Power Window:

i.

Temporarily install the power window regulator master switch assembly.


ii.

Connect the cable to the negative (-) battery terminal.


iii.

Move the front door window regulator sub-assembly LH so that the front door glass sub-assembly LH bolts can be seen.


iv.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:
w/ Curtain Shield Airbag:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



v.

Remove the power window regulator master switch assembly.



b.

w/o Power Window:

i.

Temporarily install the front door window regulator handle assembly.


ii.

Move the front door glass sub-assembly LH so that the front door glass sub-assembly LH bolts can be seen.


iii.

Remove the front door window regulator handle assembly.



c.
B412079

Remove the 2 bolts.


d.
B412080C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Remove the front door glass sub-assembly LH as shown in the illustration.

NOTICE:

Do not damage the front door glass sub-assembly LH.



Hide 67404F 24.REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH

a.
B412081

Remove the bolt.


b.

Detach the guide and remove the front door rear lower frame sub-assembly LH.


Hide 69802 25.REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY LH

a.

w/ Power Window:

Disconnect the connector.


b.

Loosen the temporarily bolt.

NOTICE:

Do not remove the temporarily bolt. If the temporarily bolt is removed, the front door window regulator sub-assembly LH may fall and become damaged.



c.

w/ Power Window:

Remove the 5 bolts and front door window regulator sub-assembly LH.


d.

w/o Power Window:

Remove the 4 bolts and front door window regulator sub-assembly LH.

B412082C01
0.115,0.052 0.344,0.25 0.229,0.198 10 true *A 3.531,0.063 3.76,0.26 0.229,0.198 10 true *B
*A w/ Power Window *B w/o Power Window
V100135

Bolt
V100136

Connector
V100137

Temporarily Bolt - -



e.

Remove the temporarily bolt from the front door window regulator sub-assembly LH.


Hide 85720C 26.REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (w/ Power Window)

Hide 27.REMOVE FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (for Driver Side)

a.
B412083C01
2.271,1.938 2.854,1.938 true 2.156,1.833 2.375,2.031 0.219,0.198 10 true *1
*1 Hole Plug
V113147

Remove in this Direction


Remove the hole plug.


b.

Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover with lock cylinder assembly.


Hide 69217D 28.REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Driver Side)

a.
B412084C01
0,0 0,0 false
V100155

Protective Tape
V113147

Remove in this Direction


Using a thin-bladed screwdriver, detach the claw and guide and remove the front door outside handle cover from the lock cylinder assembly as shown in the illustration.

HINT:

Tape the thin-bladed screwdriver tip before use.



Hide 69217D 29.REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)

a.
B412085C01
0.219,1.958 0.813,1.958 true 0.781,1.875 1.021,2.073 0.24,0.198 10 true *1
*1 Hole Plug
V113147

Remove in this Direction


Remove the hole plug.


b.

Using a T30 "TORX" socket wrench, loosen the screw.


c.

Detach the claw and remove the front door outside handle cover as shown in the illustration.


Hide 69320 30.REMOVE FRONT DOOR LOCK ASSEMBLY LH

Hide 69036A 31.REMOVE FRONT DOOR LOCK COVER SUB-ASSEMBLY LH (w/o Double Locking System)

Hide 69760C 32.REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY LH

Hide 69720B 33.REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH

Hide 69318C 34.REMOVE DOOR LOCK WIRING HARNESS SEAL

Hide 69220 35.REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH

a.
B412086C01
0,0 0,0 false
V100155

Protective Tape
V113147

Remove in this Direction


Using a thin-bladed screwdriver, detach the claw and open the connector cover as shown in the illustration.

HINT:

Tape the thin-bladed screwdriver tip before use.



b.
B412087C01
0,0 0,0 false
V100155

Protective Tape


Using a thin-bladed screwdriver, detach the claw and disconnect the connector and connector cover.

HINT:

Tape the thin-bladed screwdriver tip before use.



c.
B412088C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the front door outside handle assembly LH as shown in the illustration.


Hide 69241H 36.REMOVE FRONT DOOR FRONT OUTSIDE HANDLE PAD

a.
B412089C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the claw and remove the front door front outside handle pad.


Hide 69242E 37.REMOVE FRONT DOOR REAR OUTSIDE HANDLE PAD

a.
B412090C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the claw and remove the front door rear outside handle pad.


Hide 69202A 38.REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH

a.
B412091C01
2.167,0.708 2.448,0.333 2.448,0.333 2.615,0.333 true 0.729,1.063 0.979,1.063 0.979,1.063 1.198,0.708 true 0.844,0.188 1.073,0.188 1.073,0.188 1.219,0.396 true 2.573,0.26 2.792,0.458 0.219,0.198 10 true *a 0.667,0.083 0.854,0.292 0.188,0.208 10 true *b 0.583,0.99 0.771,1.198 0.188,0.208 10 true *b
*a Grommet
*b Guide
V113147

Remove in this Direction


Using a T30 "TORX" socket wrench, loosen the screw.


b.

Detach the grommet and guide and remove the front door outside handle frame sub-assembly LH together with the wire harness.


c.
B412092C01
2.135,1.552 2.313,1.552 2.313,1.552 2.313,1.208 false 0.76,0.885 1.083,0.885 true 1.677,1.26 1.51,1.26 1.51,1.26 1.51,1.042 false 1.698,1.177 1.896,1.406 0.198,0.229 10 true *b 0.625,0.771 0.823,1 0.198,0.229 10 true *a 2,1.438 2.198,1.667 0.198,0.229 10 true *a
*a Clamp
*b Guide


Detach the clamp and guide, disconnect the wire harness and remove the front door outside handle frame sub-assembly LH.


Hide 69312 39.REMOVE FRONT DOOR LOCK OPEN ROD LH

a.
B412093C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the snap and remove the front door lock open rod LH from the front door outside handle frame sub-assembly LH as shown in the illustration.


Hide 75720 40.REMOVE FRONT DOOR BELT MOULDING ASSEMBLY LH

Hide 67837B 41.REMOVE FRONT DOOR DUST PROOF SEAL

a.
B412094

Detach the claw and remove the 3 front door dust proof seals.


Hide 67001A 42.REMOVE FRONT DOOR PANEL CUSHION

a.
B412095

Detach the claw and remove the 2 front door panel cushions.


Hide 68620 43.REMOVE FRONT DOOR CHECK ASSEMBLY LH

a.
B412096C01
0,0 0,0 false
V100135

Bolt (A)
V100136

Bolt (B)


Remove the 2 bolts (A), bolt (B) and front door check assembly LH.


Hide 67862 44.REMOVE FRONT DOOR WEATHERSTRIP LH

a.
B412097

for Single Cab:

Using a clip remover, detach the clip and remove the front door weatherstrip LH.


b.
B412098

for Smart Cab:

Using a clip remover, detach the clip and remove the double-sided tape front door weatherstrip LH.

NOTICE:

Remove any remaining double-sided tape from the front door panel LH.



c.
B412099

for Double Cab:

Using a clip remover, detach the clip and remove the front door weatherstrip LH.


Hide 75922M 45.REMOVE NO. 1 BLACK OUT TAPE LH (w/ Black Out Tape)