Home › Engine / Hybrid System › 5L-E ENGINE CONTROL › ECD SYSTEM › from 2016.01
RM3250E _51 Engine / Hybrid System _049910 5L-E ENGINE CONTROL _0245156 ECD SYSTEM C

5L-E ENGINE CONTROL  ECD SYSTEM  P1120  Throttle / Pedal Position Sensor/Coolant Flow Control Valve Position Sensor Circuit  


DESCRIPTION

HINT:
·

This is the repair procedure for the accelerator pedal position sensor.

·

The electrical throttle system does not use a throttle cable.

·

The accelerator pedal position sensor is a non-contact type.



The accelerator pedal position sensor is mounted in the accelerator pedal to detect the opening angle of the accelerator pedal. Since this sensor is electronically controlled with hall elements, accurate control and reliability can be obtained. It has 2 sensors to detect the accelerator position and a malfunction of the accelerator position sensor.

In the accelerator pedal position sensor, the voltage applied to pedal terminals VPA and VPA2 of the ECM changes between 0 V and 5 V, in proportion to the opening angle of the accelerator pedal. The VPA is a signal to indicate the actual accelerator pedal opening angle which is used for the engine control, and the VPA2 is a signal to indicate the information about the opening angle which is used for detecting a malfunction. The ECM judges the current opening angle of the accelerator pedal from these signals input from terminals VPA and VPA2, and the ECM controls the injection pump based on these signals.

A255815E39
4.333,2.031 4.208,1.948 false 4.323,2.198 4.208,2.146 false 4.344,2.24 4.229,2.333 false 4.344,2.396 4.229,2.51 false 4.344,2.917 4.219,2.917 false 4.354,3.125 4.208,3.125 false 0.854,2.875 0.5,3.333 true 1.052,2.26 1.302,1.375 1.302,1.375 1.417,1.375 true 4.333,1.833 3.844,0.938 false 1.021,2.542 0.927,1.844 0.927,1.844 0.844,1.844 true 0.552,3.802 1.708,4.135 1.156,0.333 10 false Accelerator Pedal Position Sensor 1.458,1.302 1.938,1.479 0.479,0.177 10 false Magnet 0.313,1.76 0.844,1.938 0.531,0.177 10 false IC No. 1 0.313,3.344 0.844,3.521 0.531,0.177 10 false IC No. 2 2.063,1.74 2.531,1.917 0.469,0.177 10 false VPA 2.063,2.073 2.552,2.271 0.49,0.198 10 false EPA 2.063,2.385 2.583,2.563 0.521,0.177 10 false VCPA 2.063,2.688 2.573,2.865 0.51,0.177 10 false VPA2 2.063,3 2.563,3.198 0.5,0.198 10 false EPA2 2.063,3.323 2.583,3.5 0.521,0.177 10 false VCP2 2.677,3.76 3,3.938 0.323,0.177 10 false ECM 4.271,1.542 4.427,1.719 0.156,0.177 10 false *1 5.865,1.542 6.021,1.719 0.156,0.177 10 false *2 3.917,1.854 4.208,2.031 0.292,0.177 10 false 4.55 3.844,2.063 4.208,2.24 0.365,0.177 10 false 3.988 3.938,2.281 4.229,2.458 0.292,0.177 10 false 3.75 3.875,2.469 4.24,2.646 0.365,0.177 10 false 3.188 3.969,2.823 4.271,3 0.302,0.177 10 false 1.6 3.979,3.042 4.281,3.219 0.302,0.177 10 false 0.8 4.406,3.344 4.698,3.521 0.292,0.177 10 false 0.29 4.26,3.594 4.417,3.771 0.156,0.177 10 false 0 5.781,3.594 6.073,3.771 0.292,0.177 10 false 13.1 4.677,3.583 5.604,3.823 0.927,0.24 10 false Usable Range 4.656,3.938 6.76,4.167 2.104,0.229 10 false Accelerator Pedal Angle (°) 4.344,4.656 6.625,4.833 2.281,0.177 10 false *1: Accelerator Pedal Fully Released 4.344,4.969 6.729,5.135 2.385,0.167 10 false *2: Accelerator Pedal Fully Depressed 2.156,0.813 3.854,1.167 1.698,0.354 10 false Accelerator Pedal Position Sensor Output Voltage (V) 6.479,2.281 6.927,2.51 0.448,0.229 10 false VPA 6.438,1.823 6.865,2 0.427,0.177 10 false VPA2

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1120 Throttle / Pedal Position Sensor/Coolant Flow Control Valve Position Sensor Circuit
Condition 1, 2, 3 or 4 continues for 2.0 seconds:
1.

VPA is 0.2 V or less and VPA2 is 0.5 V or less.

2.

VPA is 4.8 V or higher.

3.

VPA2 is 4.8 V or higher, and VPA is between 0.4 V and 3.45 V.

4.

The difference between VPA and VPA2 is 0.02 V or less.


Condition 1 continues for 0.5 seconds:
1.

VPA is 0.2 V or less or VPA2 is 0.5 V or less.


·

Open or short in accelerator pedal position sensor circuit

·

Accelerator pedal rod assembly

·

ECM


Comes on DTC stored

WIRING DIAGRAM

A348544E08
0.396,3.052 0.854,3.25 0.458,0.198 10 false A41 0.375,3.229 3.177,3.583 2.802,0.354 10 false Accelerator Pedal Position Sensor 5.906,3.052 6.365,3.25 0.458,0.198 10 false G121 5.917,3.24 6.375,3.438 0.458,0.198 10 false ECM 1.604,0.542 2.063,0.74 0.458,0.198 10 false VPA 1.594,0.969 2.052,1.167 0.458,0.198 10 false EPA 1.51,1.396 2.219,1.615 0.708,0.219 10 false VCPA 1.531,1.802 1.99,2 0.458,0.198 10 false VPA2 1.531,2.219 1.99,2.417 0.458,0.198 10 false EPA2 1.531,2.635 1.99,2.833 0.458,0.198 10 false VCP2 2,2.51 2.458,2.708 0.458,0.198 10 false 1 2,2.094 2.458,2.292 0.458,0.198 10 false 2 2.01,1.677 2.469,1.875 0.458,0.198 10 false 3 2.01,1.26 2.469,1.458 0.458,0.198 10 false 4 2.01,0.844 2.469,1.042 0.458,0.198 10 false 5 2,0.417 2.458,0.615 0.458,0.198 10 false 6 5.333,0.417 5.792,0.615 0.458,0.198 10 false 20 5.323,0.833 5.781,1.031 0.458,0.198 10 false 27 5.333,1.26 5.792,1.458 0.458,0.198 10 false 26 5.333,1.677 5.792,1.875 0.458,0.198 10 false 28 5.333,2.094 5.792,2.292 0.458,0.198 10 false 29 5.333,2.51 5.792,2.708 0.458,0.198 10 false 23 5.615,2.521 6.073,2.719 0.458,0.198 10 false VCP2 5.583,2.094 6.042,2.292 0.458,0.198 10 false EPA2 5.594,1.667 6.052,1.865 0.458,0.198 10 false VPA2 5.594,1.229 6.302,1.448 0.708,0.219 10 false VCPA 5.594,0.833 6.052,1.031 0.458,0.198 10 false EPA 5.615,0.417 6.073,0.615 0.458,0.198 10 false VPA

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (ACCELERATOR POSITION)
a.
C129061C03
0.833,1.594 1.042,1.802 0.208,0.208 10 false *a 0.271,0.323 0.479,0.531 0.208,0.208 10 false *1 2.24,1.594 2.5,1.802 0.26,0.208 10 false *b
*1 Accelerator Pedal Assembly
*a Depressed
*b Released


Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Accel Sens. No.1 Volt % and Accel Sens. No.2 Volt %.

Powertrain > Engine > Data List
Tester Display
Accel Sens. No.1 Volt %
Accel Sens. No.2 Volt %
50003 234 15,16

d.

Read the values.

OK:

Check that the value displayed on the GTS changes by repeatedly depressing and releasing the accelerator pedal.



Result:
Proceed to
OK
NG



OK

2.READ DTC OUTPUT (ACCELERATOR PEDAL POSITION SENSOR DTC IS OUTPUT AGAIN)

NG

3.CHECK HARNESS AND CONNECTOR (ECM - ACCELERATOR PEDAL POSITION SENSOR)
2.READ DTC OUTPUT (ACCELERATOR PEDAL POSITION SENSOR DTC IS OUTPUT AGAIN)
a.

Connect the GTS to the DLC3.


b.

Clear the DTC.

Powertrain > Engine > Clear DTCs
50002 234

c.

Start the engine.


d.

Idle the engine for 15 seconds or more.


e.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 234

f.

Read the DTC.

Result:
Display (DTC output) Proceed to
DTC P1120 is output again A
No DTC output B




A

B

SYSTEM OK

3.CHECK HARNESS AND CONNECTOR (ECM - ACCELERATOR PEDAL POSITION SENSOR)
a.

Disconnect the accelerator pedal position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
A41-1 (VCP2) - G121-23 (VCP2) Always Below 1 Ω
A41-2 (EPA2) - G121-29 (EPA2) Always Below 1 Ω
A41-3 (VPA2) - G121-28 (VPA2) Always Below 1 Ω
A41-4 (VCPA) - G121-26 (VCPA) Always Below 1 Ω
A41-5 (EPA) - G121-27 (EPA) Always Below 1 Ω
A41-6 (VPA) - G121-20 (VPA) Always Below 1 Ω
A41-1 (VCP2) or G121-23 (VCP2) - Body ground and other terminals Always 10 kΩ or higher
A41-2 (EPA2) or G121-29 (EPA2) - Body ground and other terminals Always 10 kΩ or higher
A41-3 (VPA2) or G121-28 (VPA2) - Body ground and other terminals Always 10 kΩ or higher
A41-4 (VCPA) or G121-26 (VCPA) - Body ground and other terminals Always 10 kΩ or higher
A41-5 (EPA) or G121-27 (EPA) - Body ground and other terminals Always 10 kΩ or higher
A41-6 (VPA) or G121-20 (VPA) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT ECM
a.
A194124C62
0.25,2.188 0.719,2.448 0.469,0.26 0.948,3.094 1.417,2.458 true 1.281,2.438 0.771,2.823 true 2.01,3.115 1.885,2.469 true 1.729,2.458 1.542,3.115 true 0.219,0.188 0.76,0.552 0.542,0.365 10 false *a 1.938,3.125 2.521,3.427 0.583,0.302 10 false EPA 0.688,3.125 1.365,3.427 0.677,0.302 10 false EPA2 0.375,2.781 1.031,3.104 0.656,0.323 10 false VCP2 1.323,3.125 1.927,3.427 0.604,0.302 10 false VCPA 0.354,2.229 0.677,2.49 0.323,0.26 10 false A41
*a Front view of wire harness connector
(to Accelerator Pedal Position Sensor)


Disconnect the accelerator pedal position sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Condition Specified Condition
A41-1 (VCP2) - A41-2 (EPA2) Ignition switch ON 4.5 to 5.5 V
A41-4 (VCPA) - A41-5 (EPA) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

5.REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY

NG

5.REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY
a.

Replace the accelerator pedal rod assembly.

Click hereEngine / Hybrid System>5L-E ENGINE CONTROL>ACCELERATOR PEDAL>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.READ DTC OUTPUT (ACCELERATOR PEDAL POSITION SENSOR DTC IS OUTPUT AGAIN)
6.READ DTC OUTPUT (ACCELERATOR PEDAL POSITION SENSOR DTC IS OUTPUT AGAIN)
a.

Connect the GTS to the DLC3.


b.

Clear the DTC.

Powertrain > Engine > Clear DTCs
50002 234

c.

Start the engine.


d.

Idle the engine for 15 seconds or more.


e.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 234

f.

Read the DTC.

Result:
Display (DTC output) Proceed to
DTC P1120 is output again A
No DTC output B




A

B

SYSTEM OK