Home › Engine / Hybrid System › 5L-E ENGINE CONTROL › ECD SYSTEM › from 2016.01
RM3250E _51 Engine / Hybrid System _049910 5L-E ENGINE CONTROL _0245156 ECD SYSTEM C

5L-E ENGINE CONTROL  ECD SYSTEM  P1520  Stop Light Switch Circuit Malfunction  


DESCRIPTION

In this system, the signal of the stop light switch is used to judge whether the stop light system is abnormal or not.

The stop light switch has a duplex system (signals STP and ST1-) to recognize the abnormality when the signals of depressing and releasing the brake pedal are detected simultaneously.

HINT:

The normal signal conditions are as shown in the table below.

Signal Brake Pedal Released In Transition Brake Pedal Depressed
STP OFF ON ON
ST1- ON ON OFF


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1520 Stop Light Switch Circuit Malfunction Conditions (a), (b) and (c) continue for 0.5 seconds or more (1 trip detection logic):
(a) Ignition switch is ON.
(b) Brake pedal is released.
(c) The STP signal is off when the ST1- signal is off.
·

Open or short in stop light switch signal circuit

·

Stop light switch assembly

·

ECM


- DTC stored

WIRING DIAGRAM

A378802E02
0.646,3.844 1.198,4.073 0.552,0.229 10 false Battery 0.51,3.115 1.167,3.344 0.656,0.229 10 false FL MAIN 0.823,2.563 1.375,2.792 0.552,0.229 10 false ALT 3.448,2.531 4,2.76 0.552,0.229 10 false STOP 4.094,2.896 5.885,3.146 1.792,0.25 10 false Stop Light Switch Assembly 4.083,2.74 4.635,2.969 0.552,0.229 10 false A35 5.281,2.26 5.833,2.49 0.552,0.229 10 false 1 4.271,2.271 4.823,2.5 0.552,0.229 10 false 2 5.281,1.198 5.833,1.427 0.552,0.229 10 false 3 4.271,1.188 4.823,1.417 0.552,0.229 10 false 4 5.771,2.292 6.323,2.521 0.552,0.229 10 false 9 5.729,1.198 6.281,1.427 0.552,0.229 10 false 10 5.969,1.198 6.521,1.427 0.552,0.229 10 false ST1- 5.958,2.292 6.51,2.521 0.552,0.229 10 false STP 6.219,3.344 6.771,3.573 0.552,0.229 10 false G120 6.229,3.51 6.781,3.74 0.552,0.229 10 false ECM 3.344,1.469 4.031,1.688 0.688,0.219 10 false IG2 NO. 3 1.698,1.833 3.323,2.042 1.625,0.208 10 false Ignition Switch Assembly 1.688,1.677 2.24,1.906 0.552,0.229 10 false G1 2.521,1.208 3.073,1.438 0.552,0.229 10 false IG2 1.75,1.219 2.302,1.448 0.552,0.229 10 false AM2 1.583,1.219 2.135,1.448 0.552,0.229 10 false 4 2.844,1.188 3.396,1.417 0.552,0.229 10 false 3 0.479,1.469 1.635,1.844 1.156,0.375 10 false STRG LOCK/AM2 NO. 1

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK STOP LAMP SWITCH ASSEMBLY (TERMINAL B VOLTAGE)
a.
A253393C25
0.823,1.031 1.188,1.313 0.365,0.281 0.198,0.104 0.51,0.302 0.313,0.198 10 false *a 0.885,1.094 1.198,1.292 0.313,0.198 10 false A35
*a Front view of wire harness connector
(to Stop Light Switch)


Disconnect the stop light switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A35-2 - Body ground Always 11 to 14 V
A35-4 - Body ground Ignition switch ON 11 to 14 V



c.

Reconnect the stop light switch connector.


Result:
Proceed to
OK
NG



OK

2.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

5.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK ECM (STP AND ST1- VOLTAGE)

NG

7.REPLACE STOP LIGHT SWITCH ASSEMBLY
3.CHECK ECM (STP AND ST1- VOLTAGE)
a.
A303106C13
1.938,2.531 2.354,2.792 0.417,0.26 1.813,3.938 2.188,3.177 true 2.615,3.906 2.26,3.177 true 0.167,0.083 0.479,0.281 0.313,0.198 10 false *a 1.771,0.083 2.083,0.281 0.313,0.198 10 false *b 0.25,2.219 0.563,2.417 0.313,0.198 10 false *c 1.979,2.573 2.354,2.771 0.375,0.198 10 false G120 2.375,3.948 2.979,4.198 0.604,0.25 10 false 9 (STP) 1.573,3.969 2.198,4.219 0.625,0.25 10 false 10 (ST1-)
*a Brake Pedal Depressed
*b Brake Pedal Released
*c Component with harness connected
(ECM)


Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Brake Pedal Condition Specified Condition
G120-10 (ST1-) - Body ground Released 7.5 to 14 V
Depressed 0 to 1.5 V
G120-9 (STP) - Body ground Released 0 to 1.5 V
Depressed 7.5 to 14 V



Result:
Proceed to
OK
NG



OK

4.REPLACE ECM

NG

5.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON and turn the GTS on.


e.

Depress and release the brake pedal.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


g.

Confirm that the DTC is not output again.

Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Proceed to
NEXT



NEXT

END

7.REPLACE STOP LIGHT SWITCH ASSEMBLY
a.

Replace the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED