Home › Engine / Hybrid System › 5L-E ENGINE CONTROL › ECD SYSTEM › from 2016.01
RM3250E _51 Engine / Hybrid System _049910 5L-E ENGINE CONTROL _0245156 ECD SYSTEM J

5L-E ENGINE CONTROL  ECD SYSTEM  Air Conditioning Signal Circuit  


DESCRIPTION

When the A/C compressor is on, the A/C amplifier sends the A/C signal to the ECM and the ECM increases the fuel injection volume to improve driveability during engine idling.

WIRING DIAGRAM

A227852E05
5.896,2.354 6.333,2.552 0.438,0.198 10 false ECM 0.448,2 1.365,2.208 0.917,0.208 10 false A/C ECU 0.448,1.833 1.438,2.063 0.99,0.229 10 false G34*1, G77*2 5.885,2.177 6.313,2.344 0.427,0.167 10 false G120 5.563,0.802 6,1 0.438,0.198 10 false AC1 5.229,0.75 5.438,0.938 0.208,0.188 10 false 34 1.021,0.813 1.458,1.01 0.438,0.198 10 false AC1 1.448,0.75 2.083,0.938 0.635,0.188 10 false 2*1, 12*2 1.729,1.802 4.76,2.021 3.031,0.219 10 false *1: w/ Air Conditioner w/o PTC Heater, w/ Cooler 1.729,2.104 4,2.469 2.271,0.365 10 false *2: w/ Air Conditioner w/ PTC Heater, w/o Air Conditioner w/ PTC Heater

PROCEDURE

1.READ VALUE USING ECM
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the air conditioning switch on.

HINT:

The A/C magnetic clutch is turned on.



c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the A/C Cut Signal

Powertrain > Engine > Active Test
Tester Display
Control the A/C Cut Signal
50004 234 48

d.

Check operation of the A/C magnetic clutch cut when air conditioning cut control is operated by the GTS.

OK:

A/C magnetic clutch is turned off.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT ECM
2.INSPECT ECM
a.
A154534C88
1.906,0.229 2.313,0.479 0.406,0.25 1.906,1.042 2.135,1.719 true 1.948,0.281 2.292,0.448 0.344,0.167 10 false G120 0.135,0.052 0.365,0.219 0.229,0.167 10 false *a 1.938,1.75 2.563,1.938 0.625,0.188 10 false 34 (AC1)
*a Component with harness connected
(ECM)


Start the engine.


b.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
G120-34 (AC1) - Body ground Engine idling 11 to 14 V
G120-34 (AC1) - Body ground Ignition switch ON, engine stopped 0 to 3 V



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (ECM - AIR CONDITIONING AMPLIFIER)
3.CHECK HARNESS AND CONNECTOR (ECM - AIR CONDITIONING AMPLIFIER)
a.

Disconnect the A/C amplifier connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
for w/ Air Conditioner w/o PTC Heater, w/ Cooler
Tester Connection Condition Specified Condition
G34-2 (AC1) - G120-34 (AC1) Always Below 1 Ω
G34-2 (AC1) or G120-34 (AC1) - Body ground and other terminals Always 10 kΩ or higher

for w/ Air Conditioner w/ PTC Heater, w/o Air Conditioner w/ PTC Heater
Tester Connection Condition Specified Condition
G77-12 (AC1) - G120-34 (AC1) Always Below 1 Ω
G77-12 (AC1) or G120-34 (AC1) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR