Home › Engine / Hybrid System › 5L-E ENGINE MECHANICAL › DRIVE BELT › from 2016.01
RM3250E _51 Engine / Hybrid System _049911 5L-E ENGINE MECHANICAL _0245941 DRIVE BELT G

5L-E ENGINE MECHANICAL  DRIVE BELT  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

CAUTION:
A343690

To prevent injury due to contact with an operating fan and generator V belt or cooling fan, keep your hands and clothing away from the fan and generator V belt and cooling fans when working in the engine compartment with the engine running.


PROCEDURE

Hide 1.INSPECT V BELT

a.
A074147C01
1.313,0.188 1.479,0.354 0.167,0.167 10 false *a 0.594,0.896 0.771,1.063 0.177,0.167 10 false *c 2.344,0.188 2.5,0.354 0.156,0.167 10 false *b
*a CORRECT
*b INCORRECT
*c Clearance


Visually check the belt for cracks, oiliness or wear. Check that the belt does not touch the bottom of the pulley groove.

If necessary, replace the V belt.


b.
A374957C01
2.771,1.51 2.906,0.927 2.906,0.927 3.031,0.927 true 1.615,1.729 1.438,2.021 1.438,2.021 1.271,2.021 true 3.094,0.833 3.406,0.99 0.313,0.156 10 false *1 1.083,1.948 1.396,2.104 0.313,0.156 10 false *2
*1 Vane Pump Pulley
*2 Crankshaft Pulley
V100135

Measuring Point for V belt Deflection


Check the vane pump V belt deflection by pressing on the V belt at the point indicated in the illustration with 98 N (10 kgf, 22 lbf) of force.

Standard Deflection
Item Specified Condition
New belt 8 to 10 mm
(0.315 to 0.393 in.)
Used belt 10 to 15 mm
(0.394 to 0.590 in.)

If necessary, adjust the vane pump V belt deflection.


c.

Reference:

Using a belt tension gauge, check the vane pump V belt tension.

Standard Tension
Item Specified Condition
New belt 441 to 539 N
(45.0 to 55.0 kgf, 99.1 to 121.2 lbf)
Used belt 245 to 343 N
(25.0 to 34.9 kgf, 55.1 to 77.1 lbf)

If the V belt tension is not as specified, adjust it.

NOTICE:
·

Check the vane pump V belt tension at the specified point.

·

When installing a new V belt, set its deflection value as specified.

·

Perform the V belt tension and deflection value check after idling the engine for a few minutes.

·

When using a belt tension gauge, confirm the accuracy first by using a master gauge.

·

When reinstalling a V belt used for over 5 minutes, perform the check based on the used deflection value.

·

When checking a V belt used for over 5 minutes, confirm the deflection value is within the specified range.




d.
A374958C01
0.844,0.417 0.99,0.177 0.99,0.177 1.146,0.177 true 1.792,1.729 1.917,1.979 1.917,1.979 2.073,1.979 true 0.552,1.958 0.729,1.958 0.729,1.958 0.833,1.74 true 1.208,0.083 1.521,0.24 0.313,0.156 10 false *1 0.365,1.875 0.677,2.031 0.313,0.156 10 false *2 2.135,1.896 2.448,2.052 0.313,0.156 10 false *3
*1 Compressor Assembly with Magnet Clutch
*2 Idle Pulley
*3 Crankshaft Pulley
V100135

Measuring Point for V belt Deflection


Check the cooler compressor V belt deflection by pressing on the V belt at the point indicated in the illustration with 98 N (10 kgf, 22 lbf) of force.

Standard Drive Deflection
Item Specified Condition
New belt 11 to 15 mm
(0.434 to 0.590 in.)
Used belt 15 to 20 mm
(0.591 to 0.787 in.)

If necessary, adjust the cooler compressor V belt deflection.


e.

Reference:

Using a belt tension gauge, check the cooler compressor V belt tension.

Standard Tension
Item Specified Condition
New belt 372 to 608 N
(38.0 to 61.9 kgf, 83.7 to 136.6 lbf)
Used belt 196 to 392 N
(20.0 to 39.9 kgf, 44.1 to 88.1 lbf)

If the V belt tension is not as specified, adjust it.

NOTICE:
·

Check the cooler compressor V belt tension at the specified point.

·

When installing a new V belt, set its deflection value as specified.

·

Perform the V belt tension and deflection value check after idling the engine for a few minutes.

·

When using a belt tension gauge, confirm the accuracy first by using a master gauge.

·

When reinstalling a V belt used for over 5 minutes, perform the check based on the used deflection value.

·

When checking a V belt used for over 5 minutes, confirm the deflection value is within the specified range.




f.
A378613C02
1.698,0.74 1.896,0.375 1.896,0.375 2.052,0.375 true 1.656,1.792 1.844,2.021 1.844,2.021 2,2.021 true 0.417,1.615 0.542,1.615 0.542,1.615 0.885,1.302 true 2.104,0.292 2.417,0.448 0.313,0.156 10 false *1 0.26,1.521 0.573,1.677 0.313,0.156 10 false *2 2.063,1.938 2.375,2.094 0.313,0.156 10 false *3
*1 Water Pump Pulley
*2 Generator
*3 Crankshaft Pulley
V100135

Measuring Point for V belt Deflection


Check the fan and generator V belt deflection by pressing on the belt at the point indicated in the illustration with 98 N (10 kgf, 22 lbf) of force.

Standard Deflection
Item Specified Condition
New belt 7.0 to 10 mm
(0.276 to 0.393 in.)
Used belt 10 to 14 mm
(0.393 to 0.551 in.)

If necessary, adjust the fan and generator V belt deflection.


g.

Reference:

Using a belt tension gauge, check the fan and generator V belt tension.

Standard Tension
Item Specified Condition
New belt 441 to 539 N
(45.0 to 54.9 kgf, 99.2 to 121.1 lbf)
Used belt 196 to 343 N
(20.0 to 34.9 kgf, 44.1 to 77.1 lbf)

If the belt tension is not as specified, adjust it.

NOTICE:
·

Check the fan and generator V belt tension at the specified point.

·

When installing a new V belt, set its deflection value as specified.

·

Perform the V belt tension and deflection value check after idling the engine for a few minutes.

·

When using a belt tension gauge, confirm the accuracy first by using a master gauge.

·

When reinstalling a V belt used for over 5 minutes, perform the check based on the used deflection value.

·

When checking a V belt used for over 5 minutes, confirm the deflection value is within the specified range.