Home › Engine / Hybrid System › 5L-E ENGINE MECHANICAL › CYLINDER BLOCK › from 2016.01
RM3250E _51 Engine / Hybrid System _049911 5L-E ENGINE MECHANICAL _0245951 CYLINDER BLOCK A

5L-E ENGINE MECHANICAL  CYLINDER BLOCK  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.


a.

Install the stud bolts as shown in the illustration.

Torque:
14.5 N*m (148 kgf*cm, 11 ft.*lbf)

A071266C02
0.719,0.01 0.896,0.208 0.177,0.198 10 false *a 5.104,0.438 5.302,0.635 0.198,0.198 10 false *b 5.135,1.125 5.333,1.323 0.198,0.198 10 false *c 5.969,0.771 6.167,0.969 0.198,0.198 10 false *d
*a RH Side *b 16 mm (0.630 in.)
*c 10 mm (0.394 in.) *d 35 mm (1.38 in.)



Hide 11415 2.INSTALL CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY

a.

Apply adhesive to 2 or 3 threads of the cylinder block water drain cock sub-assembly.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



b.
A056747C02
2.813,1.021 2.604,1.021 2.604,1.021 1.958,1.49 true 2.833,0.938 3.104,1.167 0.271,0.229 10 false *a 1.646,1.927 1.938,2.125 0.292,0.198 10 true *b 1.135,1.708 1.406,1.875 0.271,0.167 10 false 45° 2.021,1.604 2.292,1.771 0.271,0.167 10 false 45°
*a Port
*b Downward


Install the cylinder block water drain cock sub-assembly.

Torque:
57 N*m (581 kgf*cm, 42 ft.*lbf)

HINT:
·

After tightening the drain cock to the specified torque, rotate the drain union clockwise until its drain port is facing downward.

·

The drain port may be set within 45° of either side of the prescribed position.



NOTICE:
·

Install the cylinder block water drain cock sub-assembly within 3 minutes after applying adhesive.

·

Do not expose the cylinder block water drain cock sub-assembly to coolant within 1 hour of installation.




c.

Rotate the cylinder block water drain cock sub-assembly clockwise to the position shown in the illustration.

NOTICE:
·

Do not rotate the cylinder block water drain cock sub-assembly by more than 1 revolution (360°) after tightening the cylinder block water drain cock sub-assembly to the specified torque.

·

Do not loosen the cylinder block water drain cock sub-assembly after setting it correctly.




Hide 15708 3.INSTALL NO. 1 OIL NOZZLE SUB-ASSEMBLY

a.
A056748

Align the pin of the No. 1 oil nozzle sub-assembly with the pin hole of the cylinder block sub-assembly.


b.

Install the 4 No. 1 oil nozzle sub-assemblies with the 4 check valves.

Torque:
25.5 N*m (260 kgf*cm, 19 ft.*lbf)


Hide 13101 4.INSTALL PISTON WITH PIN SUB-ASSEMBLY

a.
A056732

Using snap ring pliers, install a new snap ring on one side of the piston pin hole.


b.

Gradually heat the piston to approximately 60°C (140°F).


c.

Coat the piston pin with engine oil.


d.
A056726C02
0.771,0.104 0.854,0.104 0.854,0.104 1.146,0.396 false 0.729,1.167 0.802,1.167 0.802,1.167 1.104,1.771 true 0.583,0.021 0.885,0.24 0.302,0.219 10 false *a 0.531,1.083 0.896,1.271 0.365,0.188 10 false *b
*a Front Mark (Arrow)
*b Front Mark (Protrusion)


Align the front marks of the piston and connecting rod sub-assembly, connect the connecting rod sub-assembly to the piston, and then push in the piston pin with your thumb.


e.

Check the fit between the piston and piston pin. Try to move the piston back and forth on the piston pin.


f.
A056731

Using a small screwdriver, install a new snap ring on the other side of the piston pin hole.


Hide 13011 5.INSTALL PISTON RING SET

a.
A226794C06
1.688,0.146 1.688,0.469 false 1.594,1.917 1.76,2.073 0.167,0.156 10 false *b 1.594,0.49 1.76,0.646 0.167,0.156 10 false *a
*a Coil Joint
*b Oil Ring End Gap


Install the coil and oil ring by hand. Install the piston rings.

HINT:

Make sure the end gap of the oil ring and the coil joint are on opposite sides.



b.
A057243C02
0.708,0.302 0.844,0.302 0.844,0.302 0.979,0.667 true 0.979,1.333 1.125,1.688 1.125,1.688 1.25,1.688 true 0.521,0.198 0.75,0.375 0.229,0.177 10 false *a 1.302,1.604 1.552,1.823 0.25,0.219 10 false *b
*a No. 1 Piston Ring Code Mark
*b No. 2 Piston Ring Code Mark


Using a piston ring expander, install the No. 1 piston ring and No. 2 piston ring with the code marks facing upward.

Code Mark:
Item Specified Condition
No. 1 piston ring 1N
No. 2 piston ring 2N



c.
A056908C02
1.229,0.646 0.833,1.146 0.833,1.146 0.698,1.146 true 0.51,1.052 0.833,1.281 0.323,0.229 10 false *a 2.344,1.771 2.615,1.969 0.271,0.198 10 false *4 0.875,1.74 1.135,1.948 0.26,0.208 10 false *3 2.344,0.281 2.646,0.521 0.302,0.24 10 false *2 0.854,0.313 1.125,0.531 0.271,0.219 10 false *1
*1 No. 1 Piston Ring
*2 Oil Ring
*3 Coil
*4 No. 2 Piston Ring
*a Front Mark (Arrow)


Position the piston rings so that the ring ends are as shown in the illustration.

NOTICE:

Do not align the ring ends.



Hide 11711 6.INSTALL CRANKSHAFT BEARING

HINT:
A056735

Upper crankshaft bearings have an oil groove and oil hole. Lower crankshaft bearings do not.


a.

Align the crankshaft bearing claw with the claw groove of the cylinder block sub-assembly and push in the 5 upper crankshaft bearings.


b.
A056737

Align the crankshaft bearing claw with the claw groove of the crankshaft bearing cap and push in the 5 lower crankshaft bearings.


Hide 13411 7.INSTALL CRANKSHAFT

a.

Place the crankshaft on the cylinder block sub-assembly.


b.
A056733

Push the crankshaft in one direction and install one crankshaft thrust washer to the No. 3 journal position with the oil groove facing outward.


c.

Push the crankshaft in the opposite direction and install the other crankshaft thrust washer to the No. 3 journal position with the oil groove facing outward.


d.
A056734

Install the 2 crankshaft thrust washers to the No. 3 bearing cap with the grooves facing outward.


e.

Place the crankshaft on the cylinder block sub-assembly.


f.
A056294

Install the 5 crankshaft bearing caps in their proper locations.


g.
A378640E02
1.073,0.292 1.229,0.49 0.156,0.198 10 false 1 2.24,1.146 2.396,1.344 0.156,0.198 10 false 2 2.729,0.938 2.885,1.135 0.156,0.198 10 false 3 0.552,0.417 0.708,0.615 0.156,0.198 10 false 4 1.677,1.406 1.833,1.604 0.156,0.198 10 false 5 1.583,0.125 1.74,0.323 0.156,0.198 10 false 6 3,0.104 3.156,0.302 0.156,0.198 10 false 7 3.229,0.708 3.385,0.906 0.156,0.198 10 false 8 0.833,1.792 0.99,1.99 0.156,0.198 10 false 9 0.219,0.479 0.51,0.698 0.292,0.219 10 false 10

Install the crankshaft bearing cap set bolts.

HINT:
·

The crankshaft bearing cap set bolts are tightened in 2 progressive steps.

·

If a crankshaft bearing cap set bolt is broken or deformed, replace it.



i.

Apply a light coat of engine oil to the threads and under the bolt heads of the crankshaft bearing cap set bolts.


ii.

Install and uniformly tighten the 10 crankshaft bearing cap set bolts of the crankshaft bearing caps in several passes in the sequence shown in the illustration.

Torque:
105 N*m (1071 kgf*cm, 77 ft.*lbf)



h.

Check that the crankshaft turns smoothly.


Hide 8.REPLACE CRANKSHAFT THRUST CLEARANCE

Hide 13041 9.INSTALL CONNECTING ROD BEARING

a.
A057185

Align the connecting rod bearing claw with the groove of the connecting rod sub-assembly or connecting rod cap.


b.

Install the connecting rod bearings to the connecting rod and connecting rod sub-assembly cap.


Hide 10.INSTALL PISTON AND CONNECTING ROD

a.

Apply engine oil to the cylinder walls, the pistons and the surfaces of the connecting rod bearings.


b.

Check the positions of the piston ring ends.


c.
A057183

Cover the connecting rod bolts with a short piece of hose to protect the crankshaft and cylinder bore from damage.


d.
A057167C02
0.573,1.24 0.479,1.24 0.479,1.24 0.188,0.833 false 0.604,1.156 0.854,1.375 0.25,0.219 10 false *a
*a Front Mark


Using a piston ring compressor, push the correctly numbered piston and connecting rod assembly into the cylinder with the front mark of the piston facing forward.


e.

Place the connecting rod cap on the connecting rod sub-assembly.

i.

Match each numbered connecting rod cap with the correct connecting rod sub-assembly.


ii.
A057184C03
1.438,0.708 0.885,0.302 0.885,0.302 0.708,0.302 true 0.521,0.229 0.865,0.469 0.344,0.24 10 false *a
*a Front Mark


Install the connection rod cap with the front mark facing forward.



f.

Install the connecting rod cap nuts.

HINT:
·

The connecting rod nuts are tightened in 2 progressive steps.

·

If any connecting rod bolt is broken or deformed, replace it.



i.

Apply a light coat of engine oil to the threads and under the heads of the connecting rod cap nuts.


ii.

Install and alternately tighten the nuts of the connecting rod cap in several passes.

Torque:
54 N*m (551 kgf*cm, 40 ft.*lbf)

HINT:

If any one of the connecting rod cap nuts does not meet the torque specification, replace the connecting rod cap nut.




g.
A056296C01
0.333,0.969 0.49,0.969 0.49,0.969 0.625,0.438 true 0.063,0.635 0.375,0.792 0.313,0.156 10 false *a 0.156,0.885 0.469,1.042 0.313,0.156 10 false *b 0.125,0.271 0.583,0.469 0.458,0.198 10 false 90° 1.156,0.521 1.615,0.719 0.458,0.198 10 false 90°
*a Front
*b Paint Mark


Mark the front of each connecting rod cap nut with paint.


h.

Tighten the connecting rod cap nuts by 90° as shown in the illustration.


i.

Check that the painted marks are now at a 90° angle to the front.


j.

Check that the crankshaft turns smoothly.


Hide 11.INSPECT CONNECTING ROD THRUST CLEARANCE

Hide 11448 12.INSTALL CYLINDER BLOCK OIL ORIFICE

a.

Using a 6 mm hexagon socket wrench, install the cylinder block oil orifice.

Torque:
11 N*m (112 kgf*cm, 8 ft.*lbf)