Home › Drivetrain › VF2CM TRANSFER / 4WD / AWD › TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM › 2016.01–2016.03
RM3250E _52 Drivetrain _038037 VF2CM TRANSFER / 4WD / AWD _0184153 TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM J

VF2CM TRANSFER / 4WD / AWD  TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM  Clutch Switch Circuit  


DESCRIPTION

While depressing the clutch pedal, the clutch start switch assembly sends a signal to terminal MTN of the 4 wheel drive control ECU. While the signal is input, switching between H4 and L4 is possible.

WIRING DIAGRAM

C326384E04
1.656,2.948 3.656,3.156 2,0.208 10 false Clutch Start Switch Assembly 0.375,2.458 1.135,2.844 0.76,0.385 10 false to ST NO. 1 Relay 0.813,0.271 2.042,0.469 1.229,0.198 10 false from ECM 0.781,0.698 2.604,1.094 1.823,0.396 10 false from Certification ECU (Smart Key ECU Assembly)*1 0.115,3.219 2.542,3.406 2.427,0.188 10 false *1: w/ Entry and Start System 3.542,2.365 3.698,2.563 0.156,0.198 10 false 2 1.813,2.365 1.969,2.563 0.156,0.198 10 false 1 1.656,2.781 1.969,2.979 0.313,0.198 10 false B2 4.792,3.396 6.51,3.604 1.719,0.208 10 false 4 Wheel Drive Control ECU 4.771,3.188 5.229,3.385 0.458,0.198 10 false C39 5.125,2.302 5.583,2.5 0.458,0.198 10 false MTN 6.104,1.688 6.417,1.885 0.313,0.198 10 false IG 4.896,2.333 5.208,2.531 0.313,0.198 10 false 18 0.813,1.281 2.219,1.469 1.406,0.188 10 false from Ignition Switch*2 0.115,3.49 2.448,3.688 2.333,0.198 10 false *2: w/o Entry and Start System

PROCEDURE

1.READ VALUE USING GTS (CLUTCH START SWITCH)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the GTS on.


d.

Turn the ignition switch to ON.


e.

Enter the following menus: Powertrain / Four Wheel Drive / Data List.


f.

According to the display on the GTS, read the Data List.

Powertrain > Four Wheel Drive > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Clutch SW Clutch start switch status ON or OFF ON: Clutch pedal depressed
OFF: Clutch pedal released
Used only for vehicles with a manual transmission.
Displays OFF for vehicles with an automatic transmission.
Powertrain > Four Wheel Drive > Data List
Tester Display
Clutch SW
50003 363 20
OK:

The display changes according to the clutch pedal operation.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK ENGINE CONTROL SYSTEM
2.CHECK ENGINE CONTROL SYSTEM

OK

3.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - CLUTCH START SWITCH ASSEMBLY)

NG

3.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - CLUTCH START SWITCH ASSEMBLY)
a.

Disconnect the C39 4 wheel drive control ECU connector.


b.

Disconnect the B2 clutch start switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C39-18 (MTN) - B2-2 Always Below 1 Ω
C39-18 (MTN) or B2-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE 4 WHEEL DRIVE CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR