Home › Engine / Hybrid System › 1GR-FE FUEL › FUEL TANK › from 2016.01
RM3250E _51 Engine / Hybrid System _037983 1GR-FE FUEL _0177666 FUEL TANK A

1GR-FE FUEL  FUEL TANK  INSTALLATION  


PROCEDURE

Hide 77213B 1.INSTALL FUEL TANK TO FILLER PIPE HOSE

a.
A349937C01
0.854,0.813 1.083,0.625 1.083,0.625 1.24,0.625 true 0.375,1.188 0.552,1.188 0.552,1.188 0.813,0.917 true 1.271,0.531 1.51,0.74 0.24,0.208 10 false *a 0.198,1.104 0.375,1.323 0.177,0.219 10 false *b 0.448,1.667 0.833,1.906 0.385,0.24 10 false 120°
*a Protrusion
*b Paint Mark (White)


Install the fuel tank to filler pipe hose to the fuel tank sub-assembly, and tighten the clamp to secure the hose.

HINT:

Make sure the hose clamp is oriented as shown in the illustration.



Hide 77020A 2.INSTALL FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

Hide 3.INSTALL FUEL TANK CLAMP

Hide 77652A 4.INSTALL NO. 2 FUEL TANK CUSHION

a.

Install the 2 new No. 2 fuel tank cushions to the fuel tank sub-assembly.


Hide 77653A 5.INSTALL NO. 3 FUEL TANK CUSHION

a.

Install a new No. 3 fuel tank cushion to the fuel tank sub-assembly.


Hide 77697 6.INSTALL NO. 1 FUEL TANK HEAT INSULATOR

a.

Install the No. 1 fuel tank heat insulator with the 4 No. 2 fuel tank brackets.


b.

Install the nut.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 77001A 7.INSTALL FUEL TANK SUB-ASSEMBLY

a.

Set the fuel tank sub-assembly on an engine lifter and raise the fuel tank sub-assembly.

NOTICE:

Do not allow the fuel tank sub-assembly to contact the vehicle, especially the differential.



b.

Fold back approximately half of each cushion so that the wire harness can be installed in the step below.


c.

Attach the wire harness to the 6 clamps and connect the fuel sender gauge assembly connector.

NOTICE:

Be careful not to cut the wire harness.



d.

Install the 2 fuel tank bands with the 2 fuel tank band pins and 2 clips.


e.

Install the 2 fuel tank bands with the 2 bolts.

Torque:
45 N*m (459 kgf*cm, 33 ft.*lbf)


Hide 8.CONNECT FUEL TANK TO FILLER PIPE HOSE

a.
A349936C01
0.365,1.333 0.531,1.333 0.531,1.333 0.771,1.031 true 0.833,0.906 1.167,0.49 1.167,0.49 1.292,0.49 true 0.188,1.25 0.354,1.448 0.167,0.198 10 false *a 1.323,0.406 1.542,0.594 0.219,0.188 10 false *b 0.417,1.99 0.719,2.198 0.302,0.208 10 false 55° 1.115,2.042 1.417,2.25 0.302,0.208 10 false 70° 1.281,0.875 1.427,1.052 0.146,0.177 10 false *c 0.125,0.823 0.281,1.031 0.156,0.208 10 false *d
*a Protrusion
*b Paint Mark (Yellow)
*c 0 to 3 mm (0 to 0.118 in.)
*d 2 to 7 mm (0.0787 to 0.276 in.)


Connect the fuel tank to filler pipe hose to the fuel tank filler pipe sub-assembly, and tighten the clamp to secure the hose.

HINT:

Make sure the hose clamp is oriented as shown in the illustration.



Hide 9.CONNECT FUEL TANK BREATHER HOSE

a.
A349935C01
0.823,1.135 1.073,1.313 1.073,1.313 1.24,1.313 true 1.26,1.219 1.479,1.438 0.219,0.219 10 false *a 0.854,1.906 1.115,2.104 0.26,0.198 10 false *b 0.396,1.99 0.75,2.24 0.354,0.25 10 false 120°
*a Paint Mark
*b Top of Vehicle


Connect the fuel tank breather hose to the fuel tank filler pipe sub-assembly, and slide the clamp to secure the hose.

HINT:

Make sure the hose clamp is oriented as shown in the illustration.



b.

Attach the fuel tank breather hose to the clamp.


Hide 77251B 10.CONNECT FUEL MAIN TUBE AND FUEL RETURN TUBE

a.

Connect the fuel tank main tube sub-assembly and fuel tank return tube, vent line tube.

Click hereEngine / Hybrid System>1GR-FE FUEL>FUEL SYSTEM>PRECAUTION


Hide 77289B 11.INSTALL NO. 3 FUEL TUBE CLAMP

a.

Install the No. 3 fuel tube clamp to the fuel tube with the 3 claws.


Hide 77641A 12.INSTALL NO. 1 FUEL TANK PROTECTOR (for 4WD and Pre-Runner)

a.

Install the No. 1 fuel tank protector to the fuel tank sub-assembly with the 5 nuts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 77310A 13.INSTALL FUEL TANK CAP ASSEMBLY

Hide 14.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION