Home › Drivetrain › AXLE AND DIFFERENTIAL › DIFFERENTIAL SYSTEM(w/ Differential Lock) › from 2016.01
RM3250E _52 Drivetrain _038039 AXLE AND DIFFERENTIAL _0184154 DIFFERENTIAL SYSTEM(w/ Differential Lock) C

AXLE AND DIFFERENTIAL  DIFFERENTIAL SYSTEM(w/ Differential Lock)  P17C0  Rear Differential Lock Solenoid Circuit Low  


DESCRIPTION

This DTC is output when a malfunction is detected due to a short to ground occurring in the differential lock coil drive circuit of the rear differential.

DTC No. Detection Item DTC Detection Condition Trouble Area
P17C0 Rear Differential Lock Solenoid Circuit Low
·

Diagnosis Condition: Directly after ignition switch is turned to ON, or when rear differential is switched between free and locked (differential lock coil operating) with ignition switch turned to ON

·

Malfunction Status: Short to ground in differential lock coil drive circuit

·

Malfunction Time: 0.05 seconds or more

·

Other: 1 trip detection logic


·

Wire harness and connector

·

4 wheel drive control ECU

·

Differential lock coil



WIRING DIAGRAM

C325704E02
2.219,2.688 3.646,2.885 1.427,0.198 10 false Differential Lock Coil 2.229,2.5 2.542,2.698 0.313,0.198 10 false F1 3.49,1.198 3.802,1.396 0.313,0.198 10 false M1 3.49,1.781 3.802,1.979 0.313,0.198 10 false M2 3.813,1.198 3.969,1.396 0.156,0.198 10 false 2 3.781,1.76 3.938,1.958 0.156,0.198 10 false 1 4.438,3.229 4.896,3.427 0.458,0.198 10 false C40 4.438,3.417 6.188,3.604 1.75,0.188 10 false 4 Wheel Drive Control ECU 5.792,0.354 6.104,0.552 0.313,0.198 10 false IG 4.792,1.208 5.25,1.406 0.458,0.198 10 false SL+ 4.594,1.198 4.75,1.396 0.156,0.198 10 false 1 4.792,1.792 5.104,1.99 0.313,0.198 10 false SL- 4.615,1.76 4.771,1.958 0.156,0.198 10 false 5

PROCEDURE

1.CHECK DIFFERENTIAL LOCK COIL
a.

Disconnect the C40 4 wheel drive control ECU connector.


b.
C142292C09
1.542,0.854 1.927,1.135 0.385,0.281 1.125,1.74 0.656,1.271 true 1.115,2.198 0.531,2.75 true 1.615,0.917 2.073,1.115 0.458,0.198 10 false C40 0.479,1.073 1,1.271 0.521,0.198 10 false SL+ 0.365,2.792 0.823,2.99 0.458,0.198 10 false SL- 0.146,0.073 0.458,0.271 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to 4 Wheel Drive Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C40-1 (SL+) or C40-5 (SL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE 4 WHEEL DRIVE CONTROL ECU

NG

2.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - DIFFERENTIAL LOCK COIL)
2.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - DIFFERENTIAL LOCK COIL)
a.

Disconnect the C40 4 wheel drive control ECU connector.


b.

Disconnect the F1 differential lock coil connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C40-1 (SL+) or F1-2 (M1) - Body ground Always 10 kΩ or higher
C40-5 (SL-) or F1-1 (M2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR