Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE MASTER CYLINDER(w/o ABS) › from 2016.01
RM3250E _54 Brake _038045 BRAKE SYSTEM (OTHER) _0190627 BRAKE MASTER CYLINDER(w/o ABS) A

BRAKE SYSTEM (OTHER)  BRAKE MASTER CYLINDER(w/o ABS)  INSTALLATION  


PROCEDURE

Hide 1.INSPECT AND ADJUST BRAKE BOOSTER PUSH ROD

Hide 47201 2.INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY (for 1TR-FE, 2TR-FE)

NOTICE:
·

The master cylinder and piston are designed so that the piston can easily fall out. Prevent this by making sure the tip of the master cylinder points downward when handling the master cylinder.

·

Make sure foreign matter does not adhere to the piston of the master cylinder. If foreign matter adheres, clean it off with a cloth. Then apply lithium soap base glycol grease to the entire outer circumference contact surface area of the piston.



a.

Install a new O-ring to the brake master cylinder sub-assembly.


b.

Install the brake master cylinder sub-assembly, brake booster tube clamp bracket (with 4-way) and reservoir hose bracket to the brake booster assembly with the 3 nuts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


c.

Install the booster vacuum tube to the brake booster tube clamp bracket with the bolt.

Torque:
6.4 N*m (65 kgf*cm, 57 in.*lbf)


d.
A329093C03
1.719,0.542 2.031,0.698 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


Using a union nut wrench, connect the 6 brake lines to the brake master cylinder and 4-way.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.8661 in.)) + torque wrench (fulcrum length of 162 mm (6.3779 in.)): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)



NOTICE:
·

Do not damage or deform the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.




e.

Connect the brake fluid level warning switch connector to the brake master cylinder sub-assembly.


f.

Connect the clutch reservoir tube, and slide the clamp to secure it.


Hide 47201 3.INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY (for 2KD-FTV)

NOTICE:
·

The master cylinder and piston are designed so that the piston can easily fall out. Prevent this by making sure the tip of the master cylinder points downward when handling the master cylinder.

·

Make sure foreign matter does not adhere to the piston of the master cylinder. If foreign matter adheres, clean it off with a cloth. Then apply lithium soap base glycol grease to the entire outer circumference contact surface area of the piston.



a.

Install a new O-ring to the brake master cylinder sub-assembly.


b.

Install the brake master cylinder sub-assembly and brake booster tube clamp bracket (with 4-way) to the brake booster assembly with the 2 nuts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


c.
A329093C03
1.719,0.542 2.031,0.698 0.313,0.156 10 false *a
*a Wrench Fulcrum Length


Using a union nut wrench, connect the 6 brake lines to the brake master cylinder and 4-way.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.8661 in.)) + torque wrench (fulcrum length of 162 mm (6.3779 in.)): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)



NOTICE:
·

Do not damage or deform the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.




d.

Connect the brake fluid level warning switch connector to the brake master cylinder sub-assembly.


e.

Connect the clutch reservoir tube, and slide the clamp to secure it.


Hide 5.BLEED CLUTCH LINE