Home › Brake › BRAKE (REAR) › REAR BRAKE(for TSAM Made 2WD) › from 2016.01
RM3250E _54 Brake _038047 BRAKE (REAR) _0250236 REAR BRAKE(for TSAM Made 2WD) A

BRAKE (REAR)  REAR BRAKE(for TSAM Made 2WD)  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 04906 1.INSTALL REAR WHEEL CYLINDER CUP KIT

C323367C01
0,0 0,0 false
V100135

Lithium soap base glycol grease


a.

Apply a light coat of lithium soap base glycol grease to 2 new rear wheel cylinder cups and 2 rear wheel cylinder pistons.


b.

Install the 2 rear wheel cylinder cups to the 2 rear wheel cylinder pistons.


c.

Install the rear brake wheel cylinder compression spring and 2 rear wheel cylinder pistons to the rear brake wheel cylinder.


d.

Install 2 new rear wheel cylinder boots to the rear brake wheel cylinder.


Hide 47547R 2.TEMPORARILY INSTALL REAR BRAKE DRUM BLEEDER PLUG

a.

Temporarily install the rear brake drum bleeder plug to the rear brake wheel cylinder assembly LH.

HINT:

The rear brake drum bleeder plug will be tightened to the torque specification in the "Bleed Brake Line" procedures.



Hide 47548R 3.INSTALL REAR BRAKE DRUM BLEEDER PLUG CAP

Hide 47570 4.INSTALL REAR BRAKE WHEEL CYLINDER ASSEMBLY LH

a.

Install the rear brake wheel cylinder assembly LH to the backing plate with the 2 bolts.

Torque:
9.5 N*m (97 kgf*cm, 84 in.*lbf)


b.
A329093C03
1.719,0.542 2.031,0.698 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


Using a union nut wrench, connect the brake line to the rear brake wheel cylinder assembly LH.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.8661 in.)) + torque wrench (fulcrum length of 162 mm (6.3779 in.)): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)




Hide 5.APPLY HIGH-TEMPERATURE GREASE

a.
C323368C01
0,0 0,0 false
V100135

High-temperature grease


Apply high-temperature grease to the surface of the backing plate which contacts the shoe.


Hide 47602 6.INSTALL REAR BRAKE PARKING BRAKE SHOE LEVER SUB-ASSEMBLY

a.
C323369C01
0,0 0,0 false
V113147

Install in this Direction


Install the rear brake parking brake shoe lever sub-assembly with a new C-washer.


Hide 47644A 7.INSTALL REAR BRAKE AUTOMATIC ADJUST LEVER LH

a.

Using needle-nose pliers, install the rear brake automatic adjust lever LH with the E-ring.


Hide 04495 8.INSTALL REAR BRAKE SHOE

a.
C353219

Using needle-nose pliers, connect the No. 3 parking brake cable assembly to the rear brake parking brake shoe lever sub-assembly.


b.

Using needle- nose pliers, install the rear brake automatic adjust lever tension spring to the rear brake automatic adjust lever LH and rear brake shoe.


c.
C353218N01
2.135,1.104 2.135,1.938 2.135,1.938 1.99,1.938 true 1.646,1.875 1.958,2.063 0.313,0.188 10 true SST

Using SST, install the shoe, pin, shoe hold down spring and shoe hold down spring cup.

SST
09718-00011  


Hide 9.INSTALL PARKING BRAKE SHOE STRUT SET LH

a.
C353224C01
0,0 0,0 false
V100135

High-temperature grease


Disassemble the parking brake shoe strut set LH. Apply high-temperature grease to the areas indicated by the arrows in the illustration. Then reassemble the parking brake shoe strut set LH.


b.

Install the rear brake shoe return spring to the parking brake shoe strut set LH.


c.
C353225C01
2.333,0.854 2.333,0.406 2.333,0.406 2,0.406 false 1.771,0.344 1.958,0.521 0.188,0.177 10 false *1
*1 Rear Brake Shoe Return Spring


Install the parking brake shoe strut set LH as shown in the illustration.


Hide 04495 10.INSTALL FRONT BRAKE SHOE

a.
C353217N01
1.354,1.375 1.198,1.917 1.198,1.917 0.979,1.917 true 0.656,1.854 0.948,2.031 0.292,0.177 10 true SST

Using SST, install the shoe, pin, shoe hold down spring and shoe hold down spring cup.

SST
09718-00011  


Hide 11.CONNECT SHOE TENSION SPRING

a.

Connect the shoe tension spring to the front brake shoe and rear brake shoe.


Hide 12.CONNECT REAR BRAKE SHOE RETURN SPRING

a.

Connect the rear brake shoe return spring to the front brake shoe and rear brake shoe.

NOTICE:

Be careful not to damage the rear wheel cylinder boot.



Hide 42403 13.CHECK REAR BRAKE DRUM INSTALLATION

a.

Check that each part is installed properly as shown in the illustration.

C353226C01
0.396,0.177 0.583,0.344 0.188,0.167 10 false *A 3.667,0.167 3.875,0.323 0.208,0.156 10 false *B
*A LH Side *B RH Side
V100135

Front - -


NOTICE:

There should be no oil or grease on the contact surfaces of the shoe lining and rear brake drum.