This DTC is stored when a malfunction occurs in the speakers.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B15C3 | Speaker Output Short | A short is detected in the speaker output circuit | ·
Harness or connector ·
Speakers ·
Radio and display receiver assembly |
When replacing the radio and display receiver assembly, it is necessary to perform the vehicle contract setting for Connected Services (w/ Connected Services Function).
Clear the DTCs.
Recheck for DTCs and check that no DTCs are output.
No DTCs are output.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for 2 Speakers, for 4 Speakers (Single Cab)) | B |
| NG (for 4 Speakers (Double Cab, Smart Cab)) | C |
| NG (for 6 Speakers) | D |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
D
*1: for LH Side
*2: for RH Side
Disconnect the G40 radio and display receiver assembly connector.
Disconnect the K4*1 and/or J4*2 front No. 1 speaker assembly connector.
for 4 Speakers (Single Cab):
Disconnect the K7*1 and/or J7*2 front No. 2 speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G40-2 (FL+) - K4-1 | Always | Below 1 Ω |
| G40-6 (FL-) - K4-2 | Always | Below 1 Ω |
| G40-2 (FL+) or K4-1 - Body ground | Always | 10 kΩ or higher |
| G40-6 (FL-) or K4-2 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G40-2 (FL+) - K7-4 (TWL+) | Always | Below 1 Ω |
| G40-6 (FL-) - K7-2 (TWL-) | Always | Below 1 Ω |
| K7-3 (+) - K4-1 | Always | Below 1 Ω |
| K7-1 (-) - K4-2 | Always | Below 1 Ω |
| G40-2 (FL+) or K7-4 (TWL+) - Body ground | Always | 10 kΩ or higher |
| G40-6 (FL-) or K7-2 (TWL-) - Body ground | Always | 10 kΩ or higher |
| K7-3 (+) or K4-1 - Body ground | Always | 10 kΩ or higher |
| K7-1 (-) or K4-2 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G40-1 (FR+) - J4-1 | Always | Below 1 Ω |
| G40-5 (FR-) - J4-2 | Always | Below 1 Ω |
| G40-1 (FR+) or J4-1 - Body ground | Always | 10 kΩ or higher |
| G40-5 (FR-) or J4-2 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G40-1 (FR+) - J7-4 (TWR+) | Always | Below 1 Ω |
| G40-5 (FR-) - J7-2 (TWR-) | Always | Below 1 Ω |
| J7-3 (+) - J4-1 | Always | Below 1 Ω |
| J7-1 (-) - J4-2 | Always | Below 1 Ω |
| G40-1 (FR+) or J7-4 (TWR+) - Body ground | Always | 10 kΩ or higher |
| G40-5 (FR-) or J7-2 (TWR-) - Body ground | Always | 10 kΩ or higher |
| J7-3 (+) or J4-1 - Body ground | Always | 10 kΩ or higher |
| J7-1 (-) or J4-2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 1 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL
Inspect the front No. 1 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK (for 2 Speakers) |
| OK (for 4 Speakers (Single Cab)) |
| NG |
OK (for 2 Speakers)
OK (for 4 Speakers (Single Cab))
NG
Replace the front No. 2 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL
Clear the DTCs.
Recheck for DTCs and check that no DTCs are output.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
*1: for LH Side
*2: for RH Side
Disconnect the G40 and G41 radio and display receiver assembly connectors.
Disconnect the K4*1 and/or J4*2 front No. 1 speaker assembly connector.
Disconnect the M2*1 and/or L2*2 rear speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G40-2 (FL+) - K4-1 | Always | Below 1 Ω |
| G40-6 (FL-) - K4-2 | Always | Below 1 Ω |
| G41-2 (RL+) - M2-1 | Always | Below 1 Ω |
| G41-6 (RL-) - M2-2 | Always | Below 1 Ω |
| G40-2 (FL+) or K4-1 - Body ground | Always | 10 kΩ or higher |
| G40-6 (FL-) or K4-2 - Body ground | Always | 10 kΩ or higher |
| G41-2 (RL+) or M2-1 - Body ground | Always | 10 kΩ or higher |
| G41-6 (RL-) or M2-2 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G40-1 (FR+) - J4-1 | Always | Below 1 Ω |
| G40-5 (FR-) - J4-2 | Always | Below 1 Ω |
| G41-1 (RR+) - L2-1 | Always | Below 1 Ω |
| G41-3 (RR-) - L2-2 | Always | Below 1 Ω |
| G40-1 (FR+) or J4-1 - Body ground | Always | 10 kΩ or higher |
| G40-5 (FR-) or J4-2 - Body ground | Always | 10 kΩ or higher |
| G41-1 (RR+) or L2-1 - Body ground | Always | 10 kΩ or higher |
| G41-3 (RR-) or L2-2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 1 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL
Inspect the front No. 1 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear speaker assembly.
for Smart Cab: Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER(for Smart Cab)>REMOVAL
for Double Cab: Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER(for Double Cab)>REMOVAL
Inspect the rear speaker assembly.
for Smart Cab: Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER(for Smart Cab)>INSPECTION
for Double Cab: Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER(for Double Cab)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for Smart Cab: Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER(for Smart Cab)>REMOVAL
for Double Cab: Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER(for Double Cab)>REMOVAL
*1: for LH Side
*2: for RH Side
Disconnect the G40 and G41 radio and display receiver assembly connectors.
Disconnect the K4*1 and/or J4*2 front No. 1 speaker assembly connector.
Disconnect the K7*1 and/or J7*2 front No. 2 speaker assembly connector.
Disconnect the M2*1 and/or L2*2 rear speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G40-2 (FL+) - K7-4 (TWL+) | Always | Below 1 Ω |
| G40-6 (FL-) - K7-2 (TWL-) | Always | Below 1 Ω |
| K7-3 (+) - K4-1 | Always | Below 1 Ω |
| K7-1 (-) - K4-2 | Always | Below 1 Ω |
| G41-2 (RL+) - M2-1 | Always | Below 1 Ω |
| G41-6 (RL-) - M2-2 | Always | Below 1 Ω |
| G40-2 (FL+) or K7-4 (TWL+) - Body ground | Always | 10 kΩ or higher |
| G40-6 (FL-) or K7-2 (TWL-) - Body ground | Always | 10 kΩ or higher |
| K7-3 (+) or K4-1 - Body ground | Always | 10 kΩ or higher |
| K7-1 (-) or K4-2 - Body ground | Always | 10 kΩ or higher |
| G41-2 (RL+) or M2-1 - Body ground | Always | 10 kΩ or higher |
| G41-6 (RL-) or M2-2 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G40-1 (FR+) - J7-4 (TWR+) | Always | Below 1 Ω |
| G40-5 (FR-) - J7-2 (TWR-) | Always | Below 1 Ω |
| J7-3 (+) - J4-1 | Always | Below 1 Ω |
| J7-1 (-) - J4-2 | Always | Below 1 Ω |
| G41-1 (RR+) - L2-1 | Always | Below 1 Ω |
| G41-3 (RR-) - L2-2 | Always | Below 1 Ω |
| G40-1 (FR+) or J7-4 (TWR+) - Body ground | Always | 10 kΩ or higher |
| G40-5 (FR-) or J7-2 (TWR-) - Body ground | Always | 10 kΩ or higher |
| J7-3 (+) or J4-1 - Body ground | Always | 10 kΩ or higher |
| J7-1 (-) or J4-2 - Body ground | Always | 10 kΩ or higher |
| G41-1 (RR+) or L2-1 - Body ground | Always | 10 kΩ or higher |
| G41-3 (RR-) or L2-2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 1 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL
Inspect the front No. 1 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear speaker assembly.
for Smart Cab:
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER(for Smart Cab)>REMOVAL
for Double Cab:
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER(for Double Cab)>REMOVAL
Inspect the rear speaker assembly.
for Smart Cab:
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER(for Smart Cab)>INSPECTION
for Double Cab:
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER(for Double Cab)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for Smart Cab:
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER(for Smart Cab)>REMOVAL
for Double Cab:
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER(for Double Cab)>REMOVAL
Replace the front No. 2 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL
Clear the DTCs.
Recheck for DTCs and check that no DTCs are output.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG