Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) › from 2016.01
RM3250E _58 Vehicle Interior _038073 HEATING / AIR CONDITIONING _0184341 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  B1497/97  BUS IC Communication Malfunction  


DESCRIPTION

The air conditioning harness assembly connects the air conditioning amplifier assembly and the servo motors. The air conditioning amplifier assembly supplies power and sends operation instructions to each servo motor through the air conditioning harness assembly. Each servo motor sends damper position information to the air conditioning amplifier assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
B1497/97 BUS IC Communication Malfunction Error or open in communication line
·

Harness or connector

·

No. 1 air conditioning radiator damper servo sub-assembly (front side air mix), (front mode)

·

No. 2 air conditioning radiator damper servo sub-assembly (rear mode) (w/ Rear Face Register)

·

No. 1 blower damper servo sub-assembly

·

Air conditioning harness assembly

·

Air conditioning amplifier assembly


Memorized (10 seconds or more) -

HINT:

The air conditioning amplifier assembly stores the DTC of the respective malfunction if it has occurred for the period of time indicated in the parentheses.


WIRING DIAGRAM

w/ Rear Face Resister:
E315727E03
5.031,1.24 5.802,1.438 0.771,0.198 10 false BUSG 4.688,0.573 5,0.771 0.313,0.198 10 false z5 4.719,0.365 5.031,0.563 0.313,0.198 10 false 3 5.01,0.469 5.781,0.667 0.771,0.198 10 false BUS 5.01,0.865 5.781,1.063 0.771,0.198 10 false BBUS 4.688,0.979 5,1.177 0.313,0.198 10 false z5 4.677,1.354 4.99,1.552 0.313,0.198 10 false z5 4.708,0.781 5.021,0.979 0.313,0.198 10 false 4 4.708,1.167 5.021,1.365 0.313,0.198 10 false 2 0.156,3.24 2.052,3.688 1.896,0.448 10 false No. 1 Air Conditioning Radiator Damper Servo Sub-assembly 6.021,0.573 6.333,0.771 0.313,0.198 10 false IC 0.167,6.833 2.063,7.281 1.896,0.448 10 false No. 1 Blower Damper Servo Sub-assembly 0.323,0.917 0.979,1.281 0.656,0.365 10 false Front Side Air Mix 0.271,2.26 1.042,2.469 0.771,0.208 10 false Front Mode 0.219,6.104 1.073,6.542 0.854,0.438 10 false Recirculation 4.625,7.521 4.938,7.719 0.313,0.198 10 false G33 4.688,7.313 5,7.51 0.313,0.198 10 false 21 4.635,7.979 4.948,8.177 0.313,0.198 10 false G33 4.677,7.771 4.99,7.969 0.313,0.198 10 false 14 5.042,7.979 5.5,8.198 0.458,0.219 10 false GND 5.052,7.51 5.365,7.708 0.313,0.198 10 false B 3.427,7.677 4.323,7.927 0.896,0.25 10 false ECU-B NO.3 1.99,7.51 3.219,7.76 1.229,0.25 10 false from Battery 2.563,6.917 4.781,7.146 2.219,0.229 10 false Air Conditioning Harness Assembly 4.698,8.385 7.104,8.615 2.406,0.229 10 false Air Conditioning Amplifier Assembly 6.344,0.656 6.656,0.854 0.313,0.198 10 false +B 0.896,8.094 3.302,8.323 2.406,0.229 10 false : LIN Communication Line 2.448,0.448 3.219,0.646 0.771,0.198 10 false BUS 2.458,0.854 3.229,1.052 0.771,0.198 10 false BBUS 2.469,1.26 3.24,1.458 0.771,0.198 10 false BUSG 2.479,1.563 3.25,1.76 0.771,0.198 10 false M+ 2.479,1.865 3.25,2.063 0.771,0.198 10 false M- 2.458,2.188 3.229,2.385 0.771,0.198 10 false STE1 2.479,2.49 3.25,2.688 0.771,0.198 10 false STE2 2.458,2.802 3.229,3 0.771,0.198 10 false GND 0.167,5.031 2.063,5.479 1.896,0.448 10 false No. 2 Air Conditioning Radiator Damper Servo Sub-assembly* 0.281,4.313 1.052,4.521 0.771,0.208 10 false Rear Mode 0.167,8.448 3.896,8.698 3.729,0.25 10 false *: w/ Rear Face Register

w/o Rear Face Resister:
E321900E11
5.031,0.469 5.49,0.667 0.458,0.198 10 false BUS 5.031,0.854 5.615,1.052 0.583,0.198 10 false BBUS 5.031,1.24 5.615,1.438 0.583,0.198 10 false BUSG 5.031,7.5 5.615,7.698 0.583,0.198 10 false B 5.031,7.969 5.615,8.167 0.583,0.198 10 false GND 4.688,0.563 5.146,0.76 0.458,0.198 10 false z6 4.708,0.375 5.167,0.573 0.458,0.198 10 false 3 4.677,0.969 5.135,1.167 0.458,0.198 10 false z6 4.708,0.781 5.167,0.979 0.458,0.198 10 false 4 4.677,1.344 5.135,1.542 0.458,0.198 10 false z6 4.708,1.167 5.167,1.365 0.458,0.198 10 false 2 4.625,7.521 5.208,7.719 0.583,0.198 10 false G33 4.677,7.313 5.26,7.51 0.583,0.198 10 false 21 4.625,7.979 5.208,8.177 0.583,0.198 10 false G33 4.667,7.781 5.25,7.979 0.583,0.198 10 false 14 3.479,7.667 4.479,7.865 1,0.198 10 false ECU-B NO.3 1.917,7.49 3.083,7.688 1.167,0.198 10 false from Battery 0.885,8.094 2.969,8.344 2.083,0.25 10 false : LIN Communication Line 0.177,3.26 2.094,3.677 1.917,0.417 10 false No. 1 Air Conditioning Radiator Damper Servo Sub-assembly 0.26,6.854 1.969,7.271 1.708,0.417 10 false No. 1 Blower Damper Servo Sub-assembly 2.469,6.917 5.177,7.167 2.708,0.25 10 false Air Conditioning Harness Assembly 4.708,8.406 7.104,8.656 2.396,0.25 10 false Air Conditioning Amplifier Assembly 0.344,0.823 1.031,1.281 0.688,0.458 10 false Front Side Air Mix 0.281,2.26 1.042,2.708 0.76,0.448 10 false Front Mode 0.208,6.094 1.042,6.542 0.833,0.448 10 false Recirculation

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When the servo motor or air conditioning amplifier assembly is replaced, be sure to perform servo motor initialization.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)>INITIALIZATION



PROCEDURE

1.CHECK FOR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)>DTC CHECK / CLEAR

Body Electrical > Air Conditioner > Clear DTCs
50002 121

b.

Check for DTCs.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)>DTC CHECK / CLEAR

Body Electrical > Air Conditioner > Trouble Codes
50001 121
OK:

DTC B1497/97 is not output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - BATTERY AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - BATTERY AND BODY GROUND)
a.
E269948C31
1.448,0.333 1.958,0.583 0.51,0.25 3.031,1.854 2.781,1.854 2.781,1.854 2.656,1.458 true 0.927,0.479 1.177,0.479 1.177,0.479 1.375,1.26 true 0.042,0.052 0.354,0.25 0.313,0.198 10 false *a 1.563,0.375 1.875,0.573 0.313,0.198 10 false G33 3.073,1.771 3.344,1.969 0.271,0.198 10 false B 0.594,0.417 1.104,0.604 0.51,0.188 10 false GND
*a Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly)


Disconnect the air conditioning amplifier assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G33-14 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G33-21 (B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.PERFORM ACTIVE TEST USING GTS (AIR MIX SERVO TARG PULSE[D], AIR OUTLET SERVO PULSE[ D], AIR INLET DAMPER TARG PULSE, A/O SERVO PULSE[RR D])

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.PERFORM ACTIVE TEST USING GTS (AIR MIX SERVO TARG PULSE[D], AIR OUTLET SERVO PULSE[ D], AIR INLET DAMPER TARG PULSE, A/O SERVO PULSE[RR D])
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Active Test.


e.

Check the operation by referring to the table below.

Body Electrical > Air Conditioner > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Air Mix Servo Targ Pulse(D) No. 1 air conditioning radiator damper servo sub-assembly (front side air mix) target pulse Min.: 128
Max.: 383
·

Operates between 165 and 257 pulses (for LHD)

·

Operates between 255 and 347 pulses (for RHD)


Air Outlet Servo Pulse (D) No. 1 air conditioning radiator damper servo sub-assembly (front mode) pulse Min.: 128
Max.: 383
·

Operates between 143 and 257 pulses (for LHD)

·

Operates between 255 to 369 pulses (for RHD)


Air Inlet Damper Targ Pulse No. 1 blower damper servo sub-assembly (recirculation) target pulse Min.: 128
Max.: 383
Operates between 235 and 258 pulses
A/O Servo Pulse(Rr D) No. 2 air conditioning damper servo motor sub-assembly (rear mode) pulse Min.: 128
Max.: 383
·

Operates between 253 and 276 pulses

·

w/ Rear Face Register


Body Electrical > Air Conditioner > Active Test
Tester Display
Air Mix Servo Targ Pulse(D)
50004 121 24
Body Electrical > Air Conditioner > Active Test
Tester Display
Air Outlet Servo Pulse (D)
50004 121 26
Body Electrical > Air Conditioner > Active Test
Tester Display
Air Inlet Damper Targ Pulse
50004 121 27
Body Electrical > Air Conditioner > Active Test
Tester Display
A/O Servo Pulse(Rr D)
50004 121 56
OK:

Arm of the damper servo motor selected in the Active Test moves smoothly.



f.

According to the test result, proceed to the next step.


Result:
Result Proceed to
No. 1 air conditioning radiator damper servo sub-assembly (front side air mix) is malfunctioning A
No. 1 air conditioning radiator damper servo sub-assembly (front mode) is malfunctioning
No. 2 air conditioning radiator damper servo sub-assembly (rear mode) is malfunctioning (w/ Rear Face Register) B
No. 1 blower damper servo sub-assembly is malfunctioning C



A

4.CHECK NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY

B

6.CHECK NO. 2 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (REAR MODE)

C

7.CHECK NO. 1 BLOWER DAMPER SERVO SUB-ASSEMBLY
4.CHECK NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY
a.

Replace the No. 1 air conditioning radiator damper servo sub-assembly.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>FRONT AIR CONDITIONING UNIT>DISASSEMBLY

HINT:

Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or known good one and check that the condition returns to normal.



b.

Clear the DTCs.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)>DTC CHECK / CLEAR

Body Electrical > Air Conditioner > Clear DTCs
50002 121

c.

Check for DTCs.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)>DTC CHECK / CLEAR

Body Electrical > Air Conditioner > Trouble Codes
50001 121
OK:

DTC B1497/97 is not output.



Result:
Proceed to
OK
NG



OK

END (NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY IS DEFECTIVE)

NG

5.CHECK AIR CONDITIONING HARNESS ASSEMBLY
5.CHECK AIR CONDITIONING HARNESS ASSEMBLY
a.

Replace the air conditioning harness assembly.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>FRONT AIR CONDITIONING UNIT>DISASSEMBLY

HINT:

Since the air conditioning harness assembly cannot be inspected while it is removed from the vehicle, replace the air conditioning harness assembly with a new or known good one and check that the condition returns to normal.



b.

Clear the DTCs.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)>DTC CHECK / CLEAR

Body Electrical > Air Conditioner > Clear DTCs
50002 121

c.

Check for DTCs.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)>DTC CHECK / CLEAR

Body Electrical > Air Conditioner > Trouble Codes
50001 121
OK:

DTC B1497/97 is not output.



Result:
Proceed to
OK
NG



OK

END (AIR CONDITIONING HARNESS ASSEMBLY IS DEFECTIVE)

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

6.CHECK NO. 2 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (REAR MODE)
a.

Replace the No. 2 air conditioning radiator damper servo sub-assembly (rear mode).

Click hereVehicle Interior>HEATING / AIR CONDITIONING>FRONT AIR CONDITIONING UNIT>DISASSEMBLY

HINT:

Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or known good one and check that the condition returns to normal.



b.

Clear the DTCs.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)>DTC CHECK / CLEAR

Body Electrical > Air Conditioner > Clear DTCs
50002 121

c.

Check for DTCs.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)>DTC CHECK / CLEAR

Body Electrical > Air Conditioner > Trouble Codes
50001 121
OK:

DTC B1497/97 is not output.



Result:
Proceed to
OK
NG



OK

END (NO. 2 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY [REAR MODE] IS DEFECTIVE)

NG

5.CHECK AIR CONDITIONING HARNESS ASSEMBLY
7.CHECK NO. 1 BLOWER DAMPER SERVO SUB-ASSEMBLY
a.

Replace the No. 1 blower damper servo sub-assembly.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>FRONT AIR CONDITIONING UNIT>DISASSEMBLY

HINT:

Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or known good one and check that the condition returns to normal.



b.

Clear the DTCs.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)>DTC CHECK / CLEAR

Body Electrical > Air Conditioner > Clear DTCs
50002 121

c.

Check for DTCs.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)>DTC CHECK / CLEAR

Body Electrical > Air Conditioner > Trouble Codes
50001 121
OK:

DTC B1497/97 is not output.



Result:
Proceed to
OK
NG



OK

END (NO. 1 BLOWER DAMPER SERVO SUB-ASSEMBLY IS DEFECTIVE)

NG

5.CHECK AIR CONDITIONING HARNESS ASSEMBLY