| Part Tightened | N*m | kgf*cm | ft.*lbf | in.*lbf | |||
|---|---|---|---|---|---|---|---|
| Tensioner pulley x Tensioner arm | 50 | 510 | 37 | ||||
| Engine oil level dipstick guide x Timing chain cover sub-assembly | 8.0 | 82 | 71 | ||||
| Part Tightened | N*m | kgf*cm | ft.*lbf | in.*lbf | |||
|---|---|---|---|---|---|---|---|
| Camshaft timing exhaust gear assembly x No. 2 camshaft | 78 | 795 | 58 | ||||
| Camshaft timing gear assembly x Camshaft | 78 | 795 | 58 | ||||
| No. 1 camshaft bearing cap x Cylinder head sub-assembly | 15.5 | 158 | 11 | ||||
| No. 2 camshaft bearing cap x Cylinder head sub-assembly | 15.5 | 158 | 11 | ||||
| No. 1 chain tensioner assembly x Cylinder head sub-assembly | 10 | 102 | 7 | ||||
| Timing chain cover plate x Timing chain cover sub-assembly | 9.0 | 92 | 80 | ||||
| Part Tightened | N*m | kgf*cm | ft.*lbf | |||
|---|---|---|---|---|---|---|
| Cylinder head sub-assembly x Cylinder block | 1st | 39 | 398 | 29 | ||
| 2nd | Turn 90° | |||||
| 3rd | Turn 90° | |||||
| No. 4 water by-pass pipe x Cylinder head sub-assembly
(w/ Oil Cooler) |
20 | 204 | 15 | |||
| Engine wire x Cylinder head sub-assembly | for bolt A | 25 | 255 | 18 | ||
| for bolt B | 30 | 306 | 22 | |||
| No. 1 camshaft bearing cap x Cylinder head sub-assembly | 15.5 | 158 | 11 | |||
| No. 2 camshaft bearing cap x Cylinder head sub-assembly | 15.5 | 158 | 11 | |||
| Part Tightened | N*m | kgf*cm | ft.*lbf | |||
|---|---|---|---|---|---|---|
| Flywheel sub-assembly x Crankshaft
(for Manual Transmission) |
1st | 26.5 | 270 | 20 | ||
| 2nd | Turn 90° | |||||
| Drive plate and ring gear sub-assembly x Crankshaft
(for Automatic Transmission) |
74 | 755 | 55 | |||
| Part Tightened | N*m | kgf*cm | ft.*lbf | in.*lbf | |||
|---|---|---|---|---|---|---|---|
| Engine hanger x Cylinder head sub-assembly | 42 | 428 | 31 | ||||
| Front engine mounting insulator x Front No. 1 engine mounting bracket | 58 | 591 | 43 | ||||
| Front engine mounting heat insulator RH x Front engine mounting insulator | 13 | 133 | 10 | ||||
| Front engine mounting insulator x Body | 42 | 428 | 31 | ||||
| Rear end plate x Cylinder block | 18 | 184 | 13 | ||||
| No. 1 water by-pass pipe x Rear end plate | 17.5 | 178 | 13 | ||||
| Sensor bracket x Body | 30 | 306 | 22 | ||||
| Wire clamp x Front engine mounting bracket LH | 13 | 133 | 10 | ||||
| Engine wire x Engine room relay block | 12.5 | 127 | 9 | ||||
| No. 2 engine wire x Cylinder block | 27 | 275 | 20 | ||||
| No. 2 engine wire x Body | 14 | 143 | 10 | ||||
| Battery hold down clamp | 5.4 | 55 | 48 | ||||
| Positive (+) battery terminal x Battery | 5.4 | 55 | 48 | ||||
| Engine room main wire x Positive (+) battery terminal | 7.6 | 77 | 67 | ||||
| Engine wire x Air injection control bracket | 8.3 | 85 | 73 | ||||
| Engine oil level dipstick guide x Timing chain cover sub-assembly | 8.0 | 82 | 71 | ||||
| Vane pump x Timing chain cover sub-assembly | 21 | 214 | 15 | ||||
| No. 3 engine under cover x Body
(w/ Cover) |
28 | 286 | 21 | ||||
| No. 2 engine under cover x Body
(for 4WD and Pre-Runner) |
28 | 286 | 21 | ||||
| No. 1 engine under cover x Body
(for 2WD) |
28 | 286 | 21 | ||||
| No. 1 engine under cover assembly x Body
(for 2WD) |
for M8 bolt | 28 | 286 | 21 | |||
| for M10 bolt | 50 | 510 | 37 | ||||
| No. 1 engine under cover assembly x Body
(for 4WD and Pre-Runner) |
for M6 bolt | 11.5 | 117 | 8 | |||
| for M8 bolt | 28 | 286 | 21 | ||||
| Part Tightened | N*m | kgf*cm | ft.*lbf | in.*lbf | |||
|---|---|---|---|---|---|---|---|
| Rear engine oil seal retainer x Cylinder block | 13 | 133 | 10 | ||||
| No. 1 taper screw plug x Cylinder block
(w/o Oil Cooler) |
24.5 | 250 | 18 | ||||
| Union x Cylinder block
(w/ Oil Cooler) |
24.5 | 250 | 18 | ||||
| Oil filter bracket union x Cylinder block | 24.5 | 250 | 18 | ||||
| Oil filter bracket x Screw plug | 49 | 500 | 36 | ||||
| Oil filter bracket x Cylinder block | 25 | 255 | 18 | ||||
| Oil filter bracket x Oil filter union
(w/o Oil Cooler) |
43 | 438 | 32 | ||||
| No. 4 water by-pass pipe x Cylinder head sub-assembly and cylinder block
(w/ Oil Cooler) |
20 | 204 | 15 | ||||
| No. 4 chain vibration damper x Cylinder block | 18 | 184 | 13 | ||||
| Balanceshaft drive gear sub-assembly x Cylinder block | 25 | 255 | 18 | ||||
| No. 2 chain tensioner assembly x Cylinder block | 18 | 184 | 13 | ||||
| No. 3 chain vibration damper x Cylinder block | 18 | 184 | 13 | ||||
| No. 2 chain vibration damper x Cylinder block | 27 | 275 | 20 | ||||
| Oil control valve filter with the screw plug x Cylinder head sub-assembly | 30 | 306 | 22 | ||||
| No. 1 chain vibration damper x Cylinder head sub-assembly and cylinder block | for bolt | 21 | 214 | 15 | |||
| for nut | 18 | 184 | 13 | ||||
| Chain tensioner slipper x Cylinder block | 21 | 214 | 15 | ||||
| No. 1 chain tensioner assembly x Cylinder head sub-assembly | 10 | 102 | 7 | ||||
| Timing chain guide x Cylinder head sub-assembly | 10 | 102 | 7 | ||||
| Cylinder head cover connector sub-assembly x Camshaft bearing cap | 10 | 102 | 7 | ||||
| Oil pan stud bolt | 3.0 | 31 | 27 | ||||
| No. 1 ventilation connector x Cylinder head cover sub-assembly | 9.0 | 92 | 80 | ||||
| No. 1 water by-pass pipe x Timing chain cover sub-assembly | 17.5 | 178 | 13 | ||||
| No. 1 compressor mounting bracket x Cylinder block
(w/ Air Conditioning System) |
for bolt A | 45 | 459 | 33 | |||
| for bolt B | 45 | 459 | 33 | ||||
| for bolt C | 24.5 | 250 | 18 | ||||
| Idle pulley assembly x No. 1 compressor mounting bracket
(w/ Air Conditioning System) |
44 | 449 | 32 | ||||
| Front No. 1 mounting bracket RH x Cylinder block | 51 | 520 | 38 | ||||
| Front No. 1 mounting bracket LH x Cylinder block | 51 | 520 | 38 | ||||
| Engine wire x Cylinder head sub-assembly | for bolt A | 25 | 255 | 18 | |||
| for bolt B | 30 | 306 | 22 | ||||
| PCV pipe x Cylinder head sub-assembly | 18 | 184 | 13 | ||||
| Part Tightened | N*m | kgf*cm | ft.*lbf | in.*lbf | |||
|---|---|---|---|---|---|---|---|
| Cylinder head stud bolt | for stud bolt A | 3.0 | 31 | 27 | |||
| for stud bolt B | 7.5 | 76 | 66 | ||||
| for stud bolt C | 7.5 | 76 | 66 | ||||
| for stud bolt D | 7.5 | 76 | 66 | ||||
| No. 1 head straight screw plug x Cylinder head sub-assembly | 44 | 449 | 32 | ||||
| No. 2 head straight screw plug x Cylinder head sub-assembly | 140 | 1428 | 103 | ||||
| Part Tightened | N*m | kgf*cm | ft.*lbf | in.*lbf | |||
|---|---|---|---|---|---|---|---|
| Cylinder block stud bolt | 7.5 | 76 | 66 | ||||
| Cylinder block water drain cock sub-assembly x Cylinder block | 24.5 | 250 | 18 | ||||
| Water drain cock plug x Cylinder block water drain cock sub-assembly | 12.7 | 130 | 9 | ||||
| No. 1 oil nozzle sub-assembly x Cylinder block | 7.0 | 71 | 62 | ||||
| No. 2 balanceshaft driven gear x No. 2 balanceshaft | 36 | 367 | 27 | ||||
| No. 2 balanceshaft x Cylinder block | 18 | 184 | 13 | ||||
| No. 1 balanceshaft driven gear x No. 1 balanceshaft | 36 | 367 | 27 | ||||
| No. 1 balanceshaft x Cylinder block | 18 | 184 | 13 | ||||
| Crankshaft bearing cap x Cylinder block | 1st | 39 | 398 | 29 | |||
| 2nd | Turn 90° | ||||||
| Connecting rod bearing x Connecting rod | 1st | 24.5 | 250 | 18 | |||
| 2nd | Turn 90° | ||||||