Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
Use the same procedure for RHD and LHD vehicles.
The procedures listed below are for LHD vehicles.
A bolt without a torque specification is shown in the standard bolt chart.
Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS
1. REPAIR INSTRUCTION (w/ Black Out Tape)
75922M
2.INSTALL NO. 1 BLACK OUT TAPE LH (w/ Black Out Tape)
67862
3.INSTALL FRONT DOOR WEATHERSTRIP LH
for Single Cab:
Attach the clip to install the front door weatherstrip LH.
for Smart Cab:
Attach the clip to install a new front door weatherstrip LH.
Remove the peeling paper from double-sided tape and press the double-sided tape to the front of the door panel.
for Double Cab:
Attach the clip to install the front door weatherstrip LH.
68620
4.INSTALL FRONT DOOR CHECK ASSEMBLY LH
Apply MP grease to the sliding area of the front door check assembly LH.
When reusing a bolt:
Clean the threads of the bolt with non-residue solvent.
Apply adhesive to the threads of the bolt (B).
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.
|
Bolt (A) |
|
Bolt (B) |
Install the front door check assembly LH with the 2 bolts (A) and bolt (B).
67837B
5.INSTALL FRONT DOOR DUST PROOF SEAL
Attach the claw to install 3 new front door dust proof seals.
67001A
6.INSTALL FRONT DOOR PANEL CUSHION
Attach the claw to install 2 new front door panel cushions.
75720
7.INSTALL FRONT DOOR BELT MOULDING ASSEMBLY LH
69312
8.INSTALL FRONT DOOR LOCK OPEN ROD LH
|
Install in this Direction |
Attach the snap to install the front door lock open rod LH to the front door outside handle frame sub-assembly LH as shown in the illustration.
69202A
9.INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH
Apply MP grease to the sliding area of the front door outside handle frame sub-assembly LH.
| *a | Clamp |
| *b | Guide |
Attach the guide and clamp to connect the wire harness.
| *a | Grommet |
| *b | Guide |
|
Install in this Direction |
Attach the grommet and guide to install the front door outside handle frame sub-assembly LH as shown in the illustration.
Using a T30 "TORX" socket wrench, install the screw.
69242E
10.INSTALL FRONT DOOR REAR OUTSIDE HANDLE PAD
|
Install in this Direction |
Attach the claw to install the front door rear outside handle pad.
69241H
11.INSTALL FRONT DOOR FRONT OUTSIDE HANDLE PAD
|
Install in this Direction |
Attach the claw to install the front door front outside handle pad.
69220
12.INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH
|
Install in this Direction |
Install the front door outside handle assembly LH as shown in the illustration.
w/ Entry and Start System:
Connect the connector.
|
Install in this Direction |
Attach the claw to close the connector cover as shown in the illustration.
69318C
13.INSTALL DOOR LOCK WIRING HARNESS SEAL
69720B
14.INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH
69760C
15.INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY LH
69036A
16.INSTALL FRONT DOOR LOCK COVER SUB-ASSEMBLY LH (w/o Double Locking System)
69320
17.INSTALL FRONT DOOR LOCK ASSEMBLY LH
69217D
18.INSTALL FRONT DOOR OUTSIDE HANDLE COVER (for Driver Side)
|
Install in this Direction |
Attach the guide and claw to install the front door outside handle cover to the lock cylinder assembly as shown in the illustration.
19.INSTALL FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (for Driver Side)
Apply MP grease to the sliding area of the front door outside handle cover with lock cylinder assembly.
| *1 | Hole Plug |
|
Install in this Direction |
Install the front door outside handle cover with lock cylinder assembly as shown in the illustration.
Check that the front door lock cylinder assembly is inserted into the front door lock assembly LH.
Using a T30 "TORX" socket wrench, install the screw.
Install the hole plug.
69217D
20.INSTALL FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)
| *1 | Hole Plug |
|
Install in this Direction |
Attach the claw to install the front door outside handle cover as shown in the illustration.
Using a T30 "TORX" socket wrench, install the screw.
Install the hole plug.
67404F
21.INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH
Attach the guide to install the front door rear lower frame sub-assembly LH.
Install the bolt.
85720C
22.INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (w/ Power Window)
69802
23.INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY LH
Apply MP grease to the sliding area of the front door window regulator sub-assembly LH.
Temporarily install the temporarily bolt to the front door window regulator sub-assembly LH.
w/ Power Window:
Install the front door window regulator sub-assembly LH with the 5 bolts and temporarily bolt.
Connect the connector.
w/o Power Window:
Install the front door window regulator sub-assembly LH with the 4 bolts and temporarily bolt.
| *A | w/ Power Window | *B | w/o Power Window |
|
Bolt |
|
Connector |
|
Temporarily Bolt | - | - |
68102
24.INSTALL FRONT DOOR GLASS SUB-ASSEMBLY LH
w/ Power Window:
Temporarily install the power window regulator master switch assembly.
Connect the cable to the negative (-) battery terminal.
Move the front door window regulator sub-assembly LH so that the front door glass sub-assembly LH bolts can be seen.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
Remove the power window regulator master switch assembly.
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Install the front door glass sub-assembly LH as shown in the illustration.
Do not damage the front door glass sub-assembly LH.
Install the 2 bolts.
68151C
25.INSTALL FRONT DOOR GLASS RUN LH
for Single Cab, Smart Cab:
Attach the guide to install the front door glass run LH.
for Double Cab:
Attach the guide to install a new front door glass run LH.
26.INSTALL SCREW GROMMET
Attach the claw to install 2 new screw grommets.
67832
27.INSTALL FRONT DOOR SERVICE HOLE COVER LH
Apply new butyl tape to the front door panel.
| *a | Reference Point |
Pass the front door inside locking cable assembly LH and front door lock remote control cable assembly LH through a new front door service hole cover LH, and then attach the front door service hole cover LH using the reference points on the front door panel.
Securely install the front door service hole cover LH to prevent wrinkles and air bubbles.
There should be no wrinkles or folds after installing the front door service hole cover LH.
After installing the front door service hole cover LH, check the seal quality.
Attach the clamp.
w/ Power Mirror Control System:
Attach the clamp.
w/o Power Mirror Control System, w/ Side Turn Signal Light:
Attach the clamp.
w/ Curtain Shield Airbag:
Install the ground wire with the ground bolt.
87940
28.INSTALL OUTER REAR VIEW MIRROR ASSEMBLY LH
89835
29.INSTALL DOOR SIDE AIR BAG SENSOR LH (w/ Curtain Shield Airbag)
86160P
30.INSTALL FRONT NO. 2 SPEAKER ASSEMBLY (w/ Front No. 2 Speaker)
86160
31.INSTALL FRONT NO. 1 SPEAKER ASSEMBLY
68172A
32.INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP LH
Install a new front door inner glass weatherstrip LH to the front door trim board sub-assembly LH and fold down the claw in the directions indicated by the arrows in the illustration.
| *A | for Single Cab, Smart Cab | *B | for Double Cab |
69206B
33.INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY LH
|
Install in this Direction |
Attach the claw and guide to install the front door inside handle sub-assembly LH to the front door trim board sub-assembly LH.
67602
34.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH
| *1 | Front Door Inside Locking Cable Assembly LH |
| *2 | Front Door Lock Remote Control Cable Assembly LH |
|
Install in this Direction |
Attach the clamp to connect the front door lock remote control cable assembly LH and front door inside locking cable assembly LH as shown in the illustration.
|
Install in this Direction |
Attach the guide as shown in the illustration.
Attach the clip to install the front door trim board sub-assembly LH.
| *A | for Single Cab, Smart Cab | *B | for Double Cab |
Install the 3 screws.
69284C
35.INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG LH
Attach the claw to install the front door inside handle bezel plug LH as shown in the illustration.
67666B
36.INSTALL FRONT DOOR TRIM REFLECTOR LH (w/ Reflex Reflector Assembly)
| *A | for LH Side |
| *B | for RH Side |
|
Protective Tape |
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Attach the guide and claw to install the front door trim reflector LH as shown in the illustration.
Remove the protective tape.
84820
37.INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (for Driver Side, w/ Power Window)
for Models with Jam Protection Function on Driver Door Window Only:
Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>INSTALLATION
except Models with Jam Protection Function on Driver Door Window Only:
Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>INSTALLATION
84870A
38.INSTALL OUTER MIRROR SWITCH ASSEMBLY (for Driver Side, w/ Power Window)
39.INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side, w/ Power Window)
Connect each connector.
| *A | for Single Cab, Smart Cab |
| *B | for Double Cab |
|
Install in this Direction |
Attach the claw and clip to install the power window regulator master switch assembly with front door armrest base panel as shown in the illustration.
84810
40.INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Front Passenger Side, w/ Power Window)
41.INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side, w/ Power Window)
Connect the connector.
|
Install in this Direction |
Attach the claw and clip to install the power window regulator switch assembly with front door armrest base panel as shown in the illustration.
69260
42.INSTALL FRONT DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)
| *1 | Plate |
| *a | Front |
| *b | 30° |
With the door window fully closed, install the plate and front door window regulator handle with the snap ring as shown in the illustration.
74220
43.INSTALL FRONT ARMREST ASSEMBLY LH
|
Install in this Direction |
for Single Cab, Smart Cab:
Attach the claw and clip to install the front armrest assembly LH.
|
Install in this Direction |
for Double Cab:
Attach the claw and clip to install the front armrest assembly LH.
67492A
44.INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH LH
Attach the guide and clip to install the front door lower frame bracket garnish LH.
| *A | w/ Front No. 2 Speaker | *B | w/o Front No. 2 Speaker |
45.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
46.CHECK SRS WARNING LIGHT (w/ Curtain Shield Airbag)
for Type B:
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>DIAGNOSIS SYSTEM
for Type C:
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type C)>DIAGNOSIS SYSTEM