Home › Vehicle Interior › DOOR LOCK › FRONT DOOR LOCK › from 2016.03
RM3250E _58 Vehicle Interior _038064 DOOR LOCK _0186383 FRONT DOOR LOCK A

DOOR LOCK  FRONT DOOR LOCK  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the front door lock assembly removal/installation are shown below.

Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system (Click here)
Memorize steering angle neutral point Pre-crash safety system (Click here)
·

Power window regulator motor assembly

·

Door window regulator assembly

·

Door glass

·

Door glass run


Initialize power window control system
·

Jam protection function

·

Power window control system

·

Auto up and down function

·

Remote control function

·

Key-off operation function

·

Catch protection function


(Click here)

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.

·

Use the same procedure for RHD and LHD vehicles.

·

The procedures listed below are for LHD vehicles.

·

Fully open the front door glass sub-assembly LH before proceeding with work.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
w/ Curtain Shield Airbag:
B394719

Be sure to read Precaution thoroughly before servicing.

for Type B:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION

for Type C:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type C)>PRECAUTION


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
w/ Curtain Shield Airbag:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 67492A 3.REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH

Hide 74220 4.REMOVE FRONT ARMREST ASSEMBLY LH

Hide 5.REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side, w/ Power Window)

Hide 6.REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side, w/ Power Window)

Hide 69260 7.REMOVE FRONT DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)

Hide 69284C 8.REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG LH

Hide 67602 9.REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

Hide 67832 10.REMOVE FRONT DOOR SERVICE HOLE COVER LH

Hide 68151C 11.REMOVE FRONT DOOR GLASS RUN LH

Hide 68102 12.REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH

Hide 67404F 13.REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH

Hide 14.REMOVE FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (for Driver Side)

Hide 69320 15.REMOVE FRONT DOOR LOCK ASSEMBLY LH

a.
B443208C01
0.083,0.094 0.396,0.25 0.313,0.156 10 false *A 0.083,2.51 0.396,2.667 0.313,0.156 10 false *B
*A w/o Double Locking System
*B w/ Double Locking System
V100135

"Torx" Screw
V100136

Connector


Disconnect the connector.


b.

Using a T30 "TORX" socket wrench, remove the 3 screws.


c.
B438927C01
2.021,0.521 2.563,0.521 true 2.563,0.427 2.875,0.625 0.313,0.198 10 true *1
*1 Front Door Lock Open Rod LH
V113147

Remove in this Direction


Disconnect the front door lock open rod LH and remove the front door lock assembly LH as shown in the illustration.


Hide 69036A 16.REMOVE FRONT DOOR LOCK COVER SUB-ASSEMBLY LH (w/o Double Locking System)

a.
B408922C01
0,0 0,0 false
V100155

Protective Tape


Using a thin-bladed screwdriver, detach the claw and clamp and remove the front door lock cover sub-assembly LH from the front door lock assembly LH.

HINT:

Tape the thin-bladed screwdriver tip before use.



Hide 69760C 17.REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY LH

a.
B408923C01
0,0 0,0 false
V113147

Remove in this Direction


w/o Double Locking System:

Detach the guide and remove the front door inside locking cable assembly LH from the front door lock assembly LH.


b.

w/ Double Locking System:

i.
B438932

Detach the claw and open the cover.


ii.
B438933

Detach the guide and remove the front door lock remote cable assembly LH from the front door lock assembly LH.



Hide 69720B 18.REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH

a.
B408924C01
0,0 0,0 false
V113147

Remove in this Direction


w/o Double Locking System:

Detach the guide and remove the front door lock remote control cable assembly LH from the front door lock assembly LH.


b.
B438931C02
0,0 0,0 false
V113147

Remove in this Direction


w/ Double Locking System:

Detach the guide and remove the front door inside locking cable assembly LH from the front door lock assembly LH.


Hide 69318C 19.REMOVE DOOR LOCK WIRING HARNESS SEAL

a.
B438929C01
0.094,0.052 0.49,0.396 0.396,0.344 10 false *A 0.177,1.823 0.573,2.167 0.396,0.344 10 false *B
*A w/o Double Locking System
*B w/ Double Locking System
V113147

Remove in this Direction


Remove the door lock wiring harness seal from the front door lock assembly LH.