Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › REAR VIEW MONITOR SYSTEM(for Radio and Display Type) › from 2016.03
RM3250E _56 Audio / Visual / Telematics _038054 PARK ASSIST / MONITORING _0186539 REAR VIEW MONITOR SYSTEM(for Radio and Display Type) U

PARK ASSIST / MONITORING  REAR VIEW MONITOR SYSTEM(for Radio and Display Type)  TERMINALS OF ECU  


CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY


E290562N02
2.615,0.313 3.083,0.531 0.469,0.219 4.802,0.292 5.271,0.51 0.469,0.219 0.833,1.104 1.302,1.323 0.469,0.219 2.708,0.333 3.167,0.531 0.458,0.198 10 false G38 4.896,0.313 5.354,0.51 0.458,0.198 10 false G37 0.927,1.125 1.385,1.323 0.458,0.198 10 false G40

a.

Disconnect the G37 and G40 radio and display receiver assembly connectors.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition

*1: w/o Stop and Start System

*2: w/ Stop and Start System

G37-1 (IG) - Body ground G - Body ground Power source of IG Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
G40-3 (ACC1) - Body ground GR - Body ground Power source of ACC Ignition switch off Below 1 V
Ignition switch ACC 11 to 14 V*1
10.5 to 16 V*2
G40-4 (+B1) - Body ground SB - Body ground Battery Always 11 to 14 V*1
10.5 to 16 V*2
G40-7 (GND1) - Body ground BR - Body ground Ground Always Below 1 Ω


c.

Reconnect the G37 and G40 radio and display receiver assembly connectors.


d.

Measure the voltage and check for waveform according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G37-2 (REV) - Body ground R - Body ground Reverse signal Ignition switch ON, shift lever in R 7.5 to 14 V
Ignition switch ON, shift lever not in R Below 1 V
G38-12 (V+) - G38-24 (V-) R - W Display signal Ignition switch ON, shift lever in R Pulse generation (See waveform 1)
Ignition switch ON, shift lever in R, screen blacked out by covering camera lens Pulse generation (See waveform 2)
G38-11 (CA+) - G38-23 (CGND) B - Shielded Power source Ignition switch ACC 5.5 to 7.05 V
G38-23 (CGND) - Body ground Shielded - Body ground Shielding Always Below 1 V


e.
E159949N05
0.196,1.018 0.531,1.162 0.335,0.144 10 GND

Using an oscilloscope, check waveform 1.

Measurement Condition
Item Content
Terminal No. (Symbol) G38-12 (V+) - G38-24 (V-)
Tool Setting 200 mV/DIV., 50 μsec./DIV.
Condition Ignition switch ON, shift lever in R


f.
E164781N04
0.275,1.002 0.612,1.146 0.337,0.145 10 GND

Using an oscilloscope, check waveform 2.

Measurement Condition
Item Content
Terminal No. (Symbol) G38-12 (V+) - G38-24 (V-)
Tool Setting 200 mV/DIV., 50 μsec./DIV.
Condition Ignition switch ON, shift lever in R, screen blacked out by covering camera lens