Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/o Entry and Start System) › 2016.03–2016.08
RM3250E _58 Vehicle Interior _038065 THEFT DETERRENT / KEYLESS ENTRY _0184916 IMMOBILISER SYSTEM(w/o Entry and Start System) J

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/o Entry and Start System)  Engine does not Start because No Initial Combustion  


DESCRIPTION

·

When a key is inserted into the ignition key cylinder, the transponder key coil receives the key ID code and sends it to the transponder key ECU assembly.

·

If an error in communication between the transponder key coil and transponder key ECU assembly occurs, this symptom may occur.


WIRING DIAGRAM

E318145E02
4.052,0.969 4.667,1.167 0.615,0.198 10 false ANT1 4.063,1.885 4.677,2.083 0.615,0.198 10 false ANT2 3.802,0.969 4.417,1.167 0.615,0.198 10 false 4 3.729,1.885 4.344,2.083 0.615,0.198 10 false 15 1.49,0.969 2.104,1.167 0.615,0.198 10 false ANT1 1.469,1.885 2.083,2.083 0.615,0.198 10 false ANT2 0.656,2.458 1.271,2.656 0.615,0.198 10 false G17 0.667,2.615 2.469,2.833 1.802,0.219 10 false Transponder Key Coil 6.031,1.385 6.646,1.583 0.615,0.198 10 false IC 6.083,0.406 6.698,0.604 0.615,0.198 10 false 5 V 4.24,2.958 4.854,3.156 0.615,0.198 10 false G16 4.25,3.115 6.917,3.313 2.667,0.198 10 false Transponder Key ECU Assembly 2,0.979 2.615,1.177 0.615,0.198 10 false 1 2.01,1.906 2.625,2.104 0.615,0.198 10 false 5

CAUTION / NOTICE / HINT

NOTICE:

If the transponder key ECU assembly or key is replaced, refer to Service Bulletin.


PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 234
Body Electrical > Immobiliser > Clear DTCs
50002 260

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Entry and Start System)>DTC CHECK / CLEAR

Body Electrical > Immobiliser > Trouble Codes
50001 260
Powertrain > Engine > Trouble Codes
50001 234
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.



Result:
Result Proceed to
DTCs are not output (for SFI System) A
DTCs are not output (for ECD System) B
DTCs are output C



A

3.READ VALUE USING GTS (IMMOBILISER FUEL CUT)

B

4.CHECK SECURITY INDICATOR LIGHT OPERATION

C

3.READ VALUE USING GTS (IMMOBILISER FUEL CUT)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List.


e.

Read the Data List according to the display on the GTS.

Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Immobiliser Fuel Cut Status of immobiliser system fuel cut ON or OFF - -
Powertrain > Engine > Data List
Tester Display
Immobiliser Fuel Cut
50003 234 505
OK:

OFF is displayed after the engine is started.



Result:
Proceed to
OK (1TR-FE)
OK (2TR-FE)
OK (1GR-FE)
NG



OK (1TR-FE)

OK (2TR-FE)

OK (1GR-FE)

NG

4.CHECK SECURITY INDICATOR LIGHT OPERATION
4.CHECK SECURITY INDICATOR LIGHT OPERATION
a.

Check that the security indicator light turns off when a registered key is inserted into the ignition key cylinder.

OK:

Security indicator light turns off.



Result:
Proceed to
OK
NG



OK

NG

5.CHECK SECURITY INDICATOR LIGHT OPERATION
5.CHECK SECURITY INDICATOR LIGHT OPERATION
a.

Check that the security indicator light turns off when another registered key is inserted into the ignition key cylinder.

OK:

Security indicator light turns off.



Result:
Proceed to
OK
NG



OK

6.CHECK WHETHER ENGINE STARTS

NG

7.REPLACE TRANSPONDER KEY COIL
6.CHECK WHETHER ENGINE STARTS
a.

Using another registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

13.REPLACE KEY

NG

7.REPLACE TRANSPONDER KEY COIL

Result:
Proceed to
NEXT



NEXT

8.CHECK WHETHER ENGINE STARTS
8.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.



Result:
Result Proceed to
Engine can be started A
Engine cannot be started B



A

END (TRANSPONDER KEY COIL WAS DEFECTIVE)

B

9.REPLACE TRANSPONDER KEY ECU ASSEMBLY
9.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Replace the transponder key ECU assembly with a new one.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

10.REGISTER KEY
10.REGISTER KEY
a.

Register the key.

HINT:

Refer to Service Bulletin.


Result:
Proceed to
NEXT




NEXT

11.REGISTER ECU COMMUNICATION ID
11.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID.

HINT:

Refer to Service Bulletin.


Result:
Proceed to
NEXT




NEXT

12.CHECK WHETHER ENGINE STARTS
12.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)

NG

13.REPLACE KEY
13.REPLACE KEY
a.

Replace the key.

NOTICE:

Key ID code registration is necessary when replacing the key.

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

14.CHECK WHETHER ENGINE STARTS
14.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.



Result:
Result Proceed to
OK A
NG (for 1TR-FE) B
NG (for 2TR-FE) C
NG (for 1KD-FTV) D
NG (for 2KD-FTV) E
NG (for 1GD-FTV) F
NG (for 1GD-FTV (w/ DPF)) G
NG (for 2GD-FTV) H
NG (for 2GD-FTV (w/ DPF)) I
NG (for 2GD-FTV (w/ Urea SCR System)) J
NG (for 1GR-FE) K
NG (for 5L-E) L



A

END (KEY WAS DEFECTIVE)

B

C

D

E

F

G

H

I

J

K

L