Home › Engine / Hybrid System › 2GD-FTV ENGINE CONTROL › ECD SYSTEM(w/ Urea SCR System) › from 2016.03
RM3250E _51 Engine / Hybrid System _038005 2GD-FTV ENGINE CONTROL _0262511 ECD SYSTEM(w/ Urea SCR System) J

2GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  Lack of Power (Turbocharger System)  


CAUTION / NOTICE / HINT

HINT:
·

The diagnosis flowchart is for lack of power due to turbocharger factors.

·

If symptom-specific diagnosis indicates a turbocharger related problem, check using this flowchart.



PROCEDURE

1.CHECK TURBOCHARGER SUB-ASSEMBLY
a.

Check that no soot or oil adheres to the turbocharger sub-assembly connectors.

A360340E01
1.563,0.552 1.719,0.75 0.156,0.198 10 false A 3.896,0.563 4.052,0.76 0.156,0.198 10 false A 4.125,1.573 4.281,1.771 0.156,0.198 10 true A 5.063,3.104 5.219,3.302 0.156,0.198 10 false A 5.396,3.115 5.552,3.313 0.156,0.198 10 false B 4.708,3.823 4.865,4.021 0.156,0.198 10 false B 4,3.146 4.156,3.344 0.156,0.198 10 false B 4.802,2.542 4.958,2.74 0.156,0.198 10 true B

HINT:

If adhering soot or an oil leak exists, air leaking at that position may be the cause of the lack of boost pressure.



Result:
Result Proceed to
No adhering soot or an oil A
Soot adhering around the turbine housing, flange, or exhaust pipe clamp (A in the illustration) B
Oil leak from the contact surface between the compressor housing and bearing housing (B in the illustration) C



A

2.INSPECT TURBOCHARGER SUB-ASSEMBLY (TURBINE SHAFT)

B

5.CHECK EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

C

2.INSPECT TURBOCHARGER SUB-ASSEMBLY (TURBINE SHAFT)
a.

Remove the turbocharger sub-assembly.

·

Check that the turbine shaft rotates smoothly, without catching.

·

Check for loose turbine mounting nuts and for axial play in the turbine shaft.



HINT:

If the turbine shaft catches or if there is no play or excessive play, it could indicate improper sealing due to seizing or poor sliding because of a deposit build-up.


Standard value:

0.10 mm (0.00394 in.) or less


Result:
Result Proceed to
No turbine shaft malfunction A
Turbine shaft malfunction B



A

3.INSPECT TURBOCHARGER SUB-ASSEMBLY

B

3.INSPECT TURBOCHARGER SUB-ASSEMBLY
a.

Check for interference between the turbine wheel and the turbine housing.

Click hereEngine / Hybrid System>2GD-FTV INTAKE / EXHAUST>EXHAUST MANIFOLD W/ TURBOCHARGER>INSPECTION

HINT:

When there is interference between the turbine wheel and turbine housing and the turbine wheel is damaged, check for fragments of the turbine wheel in the exhaust manifold converter sub-assembly.



Result:
Result Proceed to
No damage or interference A
Damage or interference exists B



A

4.INSPECT TURBOCHARGER NOZZLE VANE PLATE

B

4.INSPECT TURBOCHARGER NOZZLE VANE PLATE
a.

Inspect the turbocharger nozzle vane plate.

i.

Remove the e-washer from the turbocharger nozzle vane control actuator.



b.
A348999

Move the turbocharger vane control rod sub-assembly and check that the turbocharger nozzle vane plate moves.


Result:
Result Proceed to
Catches, but operates* OK
Gets stuck and does not operate NG


HINT:

*: Check several times.



OK

REPLACE TURBOCHARGER NOZZLE VANE CONTROL ACTUATOR

NG

5.CHECK EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY
a.

Check for deformation or cracks in the mounting surfaces on the exhaust manifold converter sub-assembly and the turbocharger sub-assembly.

HINT:

Deformation or cracks on a mounting surface may allow exhaust gas to leak from the damaged position.


Standard:

No deformation or cracks on a mounting surface.


Result:
Result Proceed to
No problem with the mounting surface A
Deformation or cracks on the exhaust manifold converter sub-assembly mounting surface B
Deformation or cracks on the turbocharger sub-assembly mounting surface C




A

6.REPLACE EXHAUST PIPE CLAMP AND GASKET

B

REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

C

6.REPLACE EXHAUST PIPE CLAMP AND GASKET
a.

Replace the exhaust pipe clamp and the gasket.


Result:
Proceed to
NEXT



NEXT

7.PERFORM SIMULATION TEST
7.PERFORM SIMULATION TEST
a.

Check that the abnormal state has disappeared.


Result:
Proceed to
NEXT



NEXT

END