Home › Engine / Hybrid System › 2GD-FTV ENGINE CONTROL › ECD SYSTEM(w/ Urea SCR System) › from 2016.03
RM3250E _51 Engine / Hybrid System _038005 2GD-FTV ENGINE CONTROL _0262511 ECD SYSTEM(w/ Urea SCR System) C

2GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  P0420  Catalyst System Efficiency Below Threshold (Bank 1)  P244A  Diesel Particulate Filter Differential Pressure Too Low  P244B  Diesel Particulate Filter Differential Pressure Too High  P2458  Diesel Particulate Filter Regeneration Duration  P2463  Diesel Particulate Filter Restriction - Soot Accumulation  


DESCRIPTION

DPF (Diesel Particulate Filter) is an emission control system which processes the particulate matter (PM) that is emitted from a diesel engine. The DPF catalyst has a porous ceramic structure which has a PM collecting function. The PM that is collected is continuously treated by oxidation due to catalytic action at high temperatures, however PM accumulation increases at low catalyst temperatures because the oxidation process slows down. The ECM performs PM forced regeneration so that the amount of accumulated PM does not exceed the threshold.

A357988E02
1.063,0.75 0.865,0.146 0.865,0.146 1,0.146 true 2.833,1.75 3.031,1.333 3.031,1.333 3.167,1.333 true 2.979,2.354 3.177,1.938 3.177,1.938 3.313,1.938 true 3.479,2.698 3.688,2.552 3.688,2.552 3.823,2.552 true 2.854,3.406 3.542,3.073 3.542,3.073 3.635,3.073 true 2.844,3.719 3.406,4.063 3.406,4.063 3.542,4.063 true 1.802,2.354 2.406,2.208 true 1.823,2.708 2.417,2.479 true 1.76,3.365 2.406,2.833 true 3.396,6.323 3.583,6.052 true 1.344,6.583 1.615,7.188 true 3.406,6.323 4.688,6.219 true 6.021,6.771 5.698,6.563 true 6.365,6.313 6.406,6.031 true 1.083,0.083 3.042,0.292 1.958,0.208 10 false Exhaust Fuel Addition Injector 0.052,0.75 0.625,1.135 0.573,0.385 10 false Exhaust Gas 3.24,1.26 5.875,1.49 2.635,0.229 10 false Exhaust Gas Temperature Sensor 3.375,1.865 5.865,2.25 2.49,0.385 10 false No. 2 Exhaust Gas Temperature Sensor 3.865,2.469 5.646,2.677 1.781,0.208 10 false Differential Pressure Sensor 3.698,2.906 5.698,3.302 2,0.396 10 false No. 3 Exhaust Gas Temperature Sensor 3.625,3.969 5.406,4.177 1.781,0.208 10 false Air Fuel Ratio Sensor 0.885,2.281 1.802,2.49 0.917,0.208 10 false DOC Catalyst 0.135,2.625 1.823,3.031 1.688,0.406 10 false Exhaust Manifold Converter Sub-assembly 0.917,3.271 1.833,3.479 0.917,0.208 10 false DPF Catalyst 0.406,4.677 2.292,4.906 1.885,0.229 10 false DPF (Diesel Particulate Filter): 3.417,4.677 4.99,4.906 1.573,0.229 10 false Monolithic Construction: 5.563,4.677 7.135,4.906 1.573,0.229 10 false Wall-Flow Type: 2.427,5.26 3.385,5.5 0.958,0.24 10 false PM, HC, CO 2.167,6.24 3.427,6.635 1.26,0.396 10 false Alternating Blocked Passages 1.698,7.104 4.135,7.344 2.438,0.24 10 false DPF (Diesel Particulate Filter) Catalyst 6.073,6.708 6.448,6.885 0.375,0.177 10 false PM 5.417,7.073 6.49,7.292 1.073,0.219 10 false Magnified View 6.115,6.292 6.792,6.5 0.677,0.208 10 false Gas Flow 4.771,5.281 5.469,5.51 0.698,0.229 10 false CO2, H2O 3.698,6.375 4.625,6.625 0.927,0.25 10 false Cross Section

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0420 Catalyst System Efficiency Below Threshold (Bank 1) During PM forced regeneration, DOC catalyst temperature does not increase sufficiently for 3 minutes (2 trip detection logic).
·

Exhaust manifold converter sub-assembly

·

Exhaust fuel addition injector assembly


Common Inspection Item:
·

Fuel injection system

·

Intake/Exhaust system

·

After treatment control system


Comes on DTC stored
P244A Diesel Particulate Filter Differential Pressure Too Low When driving, the catalyst differential pressure is continuously below the threshold for 7 seconds or more (2 trip detection logic).
·

Exhaust manifold converter sub-assembly

·

Exhaust fuel addition injector assembly


Common Inspection Item:
·

Fuel injection system

·

Intake/Exhaust system

·

After treatment control system


Comes on DTC stored
P244B Diesel Particulate Filter Differential Pressure Too High While driving, Catalyst Differential Pressure becomes more than 0.45 for 3 seconds (1 trip detection logic).
·

Exhaust manifold converter sub-assembly

·

Differential pressure sensor


Common Inspection Item:
·

Fuel injection system

·

Intake/Exhaust system

·

After treatment control system


Comes on DTC stored
P2458 Diesel Particulate Filter Regeneration Duration When PM forced regeneration is manually performed, PM forced regeneration does not finish even after 60 minutes or more elapse (1 trip detection logic).
·

Exhaust manifold converter sub-assembly

·

Exhaust fuel addition injector assembly


Common Inspection Item:
·

Fuel injection system

·

Intake/Exhaust system

·

After treatment control system


Comes on DTC stored
P2463 Diesel Particulate Filter Restriction - Soot Accumulation While driving, PM accumulation amount exceeds the limit (1 trip detection logic).
·

Exhaust Manifold Converter sub-assembly

·

Exhaust fuel addition injector assembly


Common Inspection Item:
·

Fuel injection system

·

Intake/Exhaust system

·

After treatment control system


Comes on DTC stored

HINT:

PM forced regeneration may be prohibited due to a fail-safe operation that is performed when another DTC is stored (including engine output limitation).


Related Data List
DTC No. Data List
P0420
P244A
P244B
P2458
P2463
·

Exhaust Fuel Addition FB

·

Catalyst Differential Press

·

DPF Differential Pressure



MONITOR DESCRIPTION

The ECM monitors the differential pressure between the upstream and downstream of the DPF catalyst and also monitors exhaust gas temperature to detect a malfunction in the exhaust manifold converter sub-assembly.

Abnormal DOC catalyst temperature increase:

The ECM monitors exhaust gas temperature increase while the exhaust fuel addition injector assembly adds fuel during PM forced regeneration. Exhaust gas temperature increases up to approximately 300 to 500°C (572 to 932°F) during PM forced regeneration. If the temperature does not increase even after a certain amount of time has elapsed, the ECM determines that the DOC catalyst is abnormal and illuminates the MIL.

A208470E10
3.229,1.875 3.323,2.031 3.323,2.031 3.49,2.031 false 5.229,1.875 5.302,1.625 5.302,1.625 5.417,1.625 false 5.135,1.458 5.083,1.281 5.083,1.281 4.958,1.281 false 5.313,1.427 5.396,0.875 5.396,0.875 5.531,0.875 false 0.083,0.083 2.052,0.417 1.969,0.333 10 false Catalyst Activation Malfunction: (DPF No Activate) 0.896,0.938 2.76,1.302 1.865,0.365 10 false PM Forced Regeneration (Activation of Fuel Addition) 1.115,1.781 2.781,1.958 1.667,0.177 10 false Exhaust Gas Temperature 3.521,1.958 4.938,2.198 1.417,0.24 10 false About 300°C (572°F) 5.458,1.563 6.104,1.729 0.646,0.167 10 false Abnormal 4.49,1.208 4.969,1.375 0.479,0.167 10 false Normal 3.323,0.813 3.635,1 0.313,0.188 10 false Off 5.135,0.385 5.375,0.542 0.24,0.156 10 false On 5.563,0.802 7.063,1.146 1.5,0.344 10 false More than About 500°C (932°F) 4.24,2.438 4.594,2.594 0.354,0.156 10 false Time


Catalytic converter differential pressure too low:

The ECM monitors the DPF catalyst differential pressure when driving and illuminates the MIL when the difference in pressure before and after the catalyst is below the threshold.


Catalytic converter differential pressure too high:

The ECM compares pressure upstream and downstream of the DPF catalyst to monitor the differential pressure. If the differential pressure is large, the ECM determines that the DPF catalyst is contaminated or has deteriorated and illuminates the MIL.

A244057E10
5.979,2.354 5.802,2.354 5.802,2.354 5.573,2.146 true 2.135,3.344 2.375,3.344 2.375,3.344 2.688,2.063 true 4,1.177 4.49,0.458 4.49,0.458 4.708,0.458 true 1.229,3.271 2.125,3.625 0.896,0.354 10 false Stores P244B 3.531,2.906 4.688,3.198 1.156,0.292 10 false Mass Air Flow 0.135,0.094 2.292,0.323 2.156,0.229 10 false Differential Pressure Malfunction: 0.25,1.427 1.24,1.896 0.99,0.469 10 false DPF Differential Pressure 4.771,0.375 5.969,0.604 1.198,0.229 10 false Clogged with PM 5.76,1.031 7.146,1.458 1.385,0.427 10 false Increases PM amount of DPF catalyst 6.042,2.271 6.969,2.646 0.927,0.375 10 false No PM in DPF catalyst 1.125,0.729 1.51,0.958 0.385,0.229 10 false High 5.604,2.896 5.99,3.125 0.385,0.229 10 false High 1.125,2.563 1.51,2.792 0.385,0.229 10 false Low 1.573,2.906 1.958,3.135 0.385,0.229 10 false Low


Catalytic converter regeneration duration:

When PM forced regeneration is manually performed, PM forced generation does not finish even after 60 minutes or more elapse, the ECM determines that there is problem with the DPF catalyst and illuminates the MIL.


Excessive PM accumulation:

The ECM monitors the PM Accumulation Ratio and when the accumulated PM volume in the DPF catalyst exceeds the limit, the ECM illuminates the MIL.


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0420
P244A
P2458
P2463
PM forced regeneration
P244B Engine is running at 4000 rpm with no load for 10 seconds or more.

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing an injector assembly, the ECM needs registration.

Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM(w/ Urea SCR System)>REGISTRATION

·

After turning ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



HINT:
·

If DTC P2458 or P2463 is stored, fail-safe controls engine power output and PM forced regeneration is prohibited. In this case, PM forced regeneration can be performed after disconnecting the EFI-B fuse or battery terminal and waiting for 60 seconds or more before connecting it again.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.READ DTC OUTPUT (RECORD STORED DTC AND FREEZE FRAME DATA)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Record the stored DTC and freeze frame data.

Powertrain > Engine > Trouble Codes
50001 61

f.

Check Exhaust Fuel Addition FB and Catalyst Differential Press in the freeze frame data.

HINT:
·

When the Exhaust Fuel Addition FB value is 1.45 or more, it indicates a high possibility of insufficient temperature increase during PM regeneration control.

·

When the Catalyst Differential Press value is more than 0.45, it indicates a high possibility that DPF catalyst is clogged.




Result:
Proceed to
NEXT



NEXT

2.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0420, P244A, P244B, P2458 AND P2463)
2.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0420, P244A, P244B, P2458 AND P2463)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 234
Result:
Result Proceed to
DTC P244A is output A
DTC P244B is output B
DTC P244B is output at the same time as P2463
DTC P0420, P2458 or P2463 is output C
Other relevant DTCs are output D


HINT:

When DTC P1603, P1604 or P1608 is output in addition to P0420, perform troubleshooting for P1603, P1604 or P1608 first.




A

3.CHECK BLOCKAGE OF AIR HOSE AND VACUUM PIPE (DIFFERENTIAL PRESSURE SENSOR - VACUUM PIPE)

C

11.CHECK FOR BLACK SMOKE

D

10.GO TO DTC CHART

B

22.READ VALUE USING GTS (DPF DIFFERENTIAL PRESSURE)
3.CHECK BLOCKAGE OF AIR HOSE AND VACUUM PIPE (DIFFERENTIAL PRESSURE SENSOR - VACUUM PIPE)
CAUTION:

Be careful of being burned by exhaust gases during the following inspection.


HINT:

Before checking the differential pressure sensor, perform a visual inspection of the differential pressure pipes and check that they are properly connected and no air is leaking from the pipes or hoses. If a malfunction is found, repair it before checking the sensor.


A360341C01
4.396,2.135 4.99,1.563 4.99,1.563 5.083,1.563 true 2.198,1.417 2.292,1.417 2.292,1.417 2.698,2.01 true 3.688,1.031 4.521,0.302 4.521,0.302 4.615,0.302 true 2.917,0.323 3.01,0.323 3.01,0.323 3.417,0.917 true 2.74,0.25 3.052,0.406 0.313,0.156 10 false *1 4.656,0.229 4.969,0.385 0.313,0.156 10 false *2 2.042,1.354 2.354,1.51 0.313,0.156 10 false *3 5.125,1.49 5.438,1.646 0.313,0.156 10 false *4
*1 Air Hose (Downstream) *2 Air Hose (Upstream)
*3 No. 2 Vacuum Pipe *4 No. 1 Vacuum Pipe


a.
A362182C03
0.615,0.958 1.667,1.302 true 0.625,0.958 1.323,0.844 false 0.458,0.885 0.771,1.042 0.313,0.156 10 false *1
*1 Air Hose


Disconnect the air hoses (both upstream and downstream) from the differential pressure sensor.


b.

Start the engine.


c.

Check if there are exhaust gas pulsations from both air hoses during idling.

OK:

Exhaust gas pulsation exists.



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (DPF DIFFERENTIAL PRESSURE)

NG

9.REPAIR OR REPLACE NO. 1 VACUUM PIPE OR NO. 2 VACUUM PIPE
4.READ VALUE USING GTS (DPF DIFFERENTIAL PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / DPF Differential Pressure.


d.

Check that the differential pressure is as specified below.

Powertrain > Engine > Data List
Tester Display
DPF Differential Pressure
50003 61 238
OK:

Approximately 0 kPa



Result:
Proceed to
OK
NG



OK

5.CONNECT UPSTREAM AIR HOSE

NG

6.REPLACE DIFFERENTIAL PRESSURE SENSOR
5.CONNECT UPSTREAM AIR HOSE
a.
A362181C01
1.75,1.198 2.073,0.99 2.073,0.99 2.188,0.99 true 2.25,0.927 2.563,1.125 0.313,0.198 10 false *1
*1 Air Hose (Upstream)


Connect the upstream air hose to the differential pressure sensor.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / DPF Differential Pressure.


e.

Start the engine.


f.

Engine is running at 4000 rpm with no load for 10 seconds or more.


g.

Check that the differential pressure is as specified below.

Powertrain > Engine > Data List
Tester Display
DPF Differential Pressure
50003 234 844
Result:
DPF Differential Pressure Proceed to
1.5 kPa or higher A
Below 1.5 kPa B




B

6.REPLACE DIFFERENTIAL PRESSURE SENSOR

A

7.CONNECT DOWNSTREAM AIR HOSE
6.REPLACE DIFFERENTIAL PRESSURE SENSOR
a.

Result:
Proceed to
NEXT



NEXT

7.CONNECT DOWNSTREAM AIR HOSE
7.CONNECT DOWNSTREAM AIR HOSE
a.

Connect the downstream air hose to the differential pressure sensor.

A360341C04
2.917,0.323 3.01,0.323 3.01,0.323 3.417,0.917 true 2.74,0.25 3.052,0.406 0.313,0.156 10 false *1
*1 Air Hose (Downstream) - -



b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / DPF Differential Pressure.


e.

Start the engine.


f.

Engine is running at 4000 rpm with no load for 10 seconds or more.


g.

Check that the differential pressure is as specified below.

Powertrain > Engine > Data List
Tester Display
DPF Differential Pressure
50003 234 844
Result:
DPF Differential Pressure Proceed to
-1.5 to 1.5 kPa A
Higher than 1.5 kPa B




A

8.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

B

11.CHECK FOR BLACK SMOKE
8.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY
a.

It has been determined that the exhaust manifold converter sub-assembly needs to be replaced. However, perform all the troubleshooting procedures before replacing the exhaust manifold converter sub-assembly.

HINT:

If the differential pressure before and after the DPF is low, it is very likely that there is no DPF or the material inside the DPF is missing due to erosion, etc. If the DPF catalyst is eroded, do not replace the DPF at this time, as troubleshooting the cause and other repairs are necessary.



Result:
Proceed to
NEXT



NEXT

13.CHECK FOR WHITE SMOKE (DURING PM FORCED REGENERATION)
9.REPAIR OR REPLACE NO. 1 VACUUM PIPE OR NO. 2 VACUUM PIPE
a.

Repair or replace No. 1 vacuum pipe or No. 2 vacuum pipe.


Result:
Proceed to
NEXT



NEXT

4.READ VALUE USING GTS (DPF DIFFERENTIAL PRESSURE)
10.GO TO DTC CHART

NEXT

11.CHECK FOR BLACK SMOKE
11.CHECK FOR BLACK SMOKE
a.

Start the engine and drive the vehicle until the engine coolant temperature reaches 75°C (167°F) or higher.


b.

Stop the vehicle and allow the engine to idle.


c.

Fully depress the accelerator pedal for 5 seconds, and then release it [A].


d.

Repeat the procedure [A] 10 times [B].


e.

Check for black smoke emission during the procedures [A] and [B].

OK:

Black smoke is emitted less than 5 times.


HINT:

Even if the black smoke is very thin, count the number of black smoke emissions if there is any visible smoke.



Result:
Proceed to
OK
NG



NG

12.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

OK

13.CHECK FOR WHITE SMOKE (DURING PM FORCED REGENERATION)
12.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY
a.

It has been determined that the exhaust manifold converter sub-assembly needs to be replaced. However, perform all the troubleshooting procedures before replacing the exhaust manifold converter sub-assembly.

HINT:

This DTC is stored because an excessive amount of PM has accumulated and resulted in abnormal combustion. It is necessary to diagnose the cause of abnormal PM accumulation and repair the problem. Therefore, do not perform replacement at this time.



Result:
Proceed to
NEXT



NEXT

13.CHECK FOR WHITE SMOKE (DURING PM FORCED REGENERATION)
13.CHECK FOR WHITE SMOKE (DURING PM FORCED REGENERATION)
a.

Remove the EFI-B fuse or disconnect the cable from the battery terminal for 60 seconds or more, and then reinstall the EFI-B fuse or reconnect the cable to the battery terminal.

HINT:
·

The amount of built up particulate matter recorded by the ECM cannot be initialized by the GTS.

·

If the amount of built up particulate matter recorded by the ECM is not initialized, PM forced regeneration cannot be performed using the GTS.




b.

Turn the ignition switch to ON.


c.

Turn the ignition switch off and wait for 30 seconds or more.


d.

Turn the ignition switch to ON and wait for 10 seconds or more.


e.

Connect the GTS to the DLC3.


f.

Turn the ignition switch to ON and turn the GTS on.


g.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.


h.

Maintain the maximum possible engine speed under no load for 10 seconds to blow out all soot from inside the exhaust pipe.

HINT:
·

If only a low engine speed is continuously maintained, soot may accumulate at the end of the catalyst.

·

When soot accumulates at the end of the catalyst, it may not be possible to perform PM forced regeneration control normally.




i.

Enter the following menus: Powertrain / Engine / Active Test / Activate the DPF Rejuvenate (PM) / Data List / Diesel Exhaust / Exhaust Temperature B1S2.


j.

Perform the Active Test.

Powertrain > Engine > Active Test
Active Test Display
Activate the DPF Rejuvenate (PM)
Data List Display
Exhaust Temperature B1S2
50004 234 97 859
CAUTION:

Be careful of the exhaust pipes and surrounding areas, as they become extremely hot when performing PM forced regeneration.


HINT:

When PM Accumulation Ratio is too low, Activate the DPF Rejuvenate (PM) cannot be performed. Therefore, rev the engine with no load at 3400 rpm for 5 to 10 minutes to increase PM Accumulation Ratio to 12% or more.



k.

Check for temperature increases and abnormal white smoke during PM forced regeneration.

HINT:
·

PM forced regeneration takes 15 to 40 minutes to finish.

·

The time it takes to complete PM forced regeneration changes depending on "PM Accumulation Ratio" and the vehicle operating conditions.

·

If the value of "Catalyst Differential Press" increases too much during the PM forced regeneration, the fail-safe function activates and PM forced regeneration is stopped.

·

Perform PM forced regeneration control until the display on the multi-information display turns off.

·

If actions such as depressing the accelerator pedal or clutch pedal, etc. are performed during PM forced regeneration, PM forced regeneration stops. If PM forced regeneration stops, it is necessary to perform it again.

·

PM forced regeneration control is not complete until the display on the multi-information display turns off.



Result:
Result Proceed to
During PM forced regeneration, temperature of Exhaust Temperature B1S2 is 300 to 500°C and no white smoke is generated A
During PM forced regeneration, temperature of Exhaust Temperature B1S2 is 300 to 500°C and abnormal white smoke is generated*1 B
Other than above*2 C


HINT:
·

*1: If abnormal white smoke is only generated during PM forced regeneration, there may be uncombusted fuel due to deterioration of the DPF catalyst.

·

*1: When there is a malfunction with combustion control, operation performance may be reduced and abnormalities may be felt even if PM forced regeneration is performed.

·

*2: An excess of accumulated PM is the result of a malfunction in the control system causing poor combustion and an increase in black smoke.





A

14.REPLACE EXHAUST FUEL ADDITION INJECTOR ASSEMBLY

B

15.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

C

16.CHECK FUEL INJECTION SYSTEM
14.REPLACE EXHAUST FUEL ADDITION INJECTOR ASSEMBLY
a.

It has been determined that the exhaust fuel addition injector assembly needs to be replaced. However, perform all the troubleshooting procedures before replacing the exhaust fuel addition injector assembly.


Result:
Proceed to
NEXT



NEXT

16.CHECK FUEL INJECTION SYSTEM
15.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY
a.

It has been determined that the exhaust manifold converter sub-assembly needs to be replaced. However, perform all the troubleshooting procedures before replacing the exhaust manifold converter sub-assembly.

HINT:

If abnormal white smoke is only generated during PM forced regeneration, there may be uncombusted fuel due to deterioration of the DPF catalyst. When there is a malfunction with combustion control, operation performance may be reduced and abnormalities may be felt even if PM forced regeneration is performed.



Result:
Proceed to
NEXT



NEXT

16.CHECK FUEL INJECTION SYSTEM
16.CHECK FUEL INJECTION SYSTEM

Result:
Proceed to
NEXT



NEXT

17.CHECK INTAKE/EXHAUST SYSTEM
17.CHECK INTAKE/EXHAUST SYSTEM

Result:
Proceed to
NEXT



NEXT

18.CHECK AFTER TREATMENT CONTROL SYSTEM
18.CHECK AFTER TREATMENT CONTROL SYSTEM

Result:
Proceed to
NEXT



NEXT

19.REPAIR OR REPLACE MALFUNCTIONING PARTS
19.REPAIR OR REPLACE MALFUNCTIONING PARTS
HINT:

Replace the following items only when it has been determined necessary based on diagnosis for DTC P0420, P244A, P244B, P2458 and P2463.


a.

Replace the exhaust manifold converter sub-assembly.

Click hereEngine / Hybrid System>2GD-FTV EMISSION CONTROL>MONOLITHIC CONVERTER(w/ DPF)>REMOVAL

NOTICE:

Perform the initialization procedure for "DPF catalyst record clear" and "DPF Deterioration Record Clear"

Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM(w/ Urea SCR System)>INITIALIZATION



b.

Replace the exhaust fuel addition injector assembly.

Click hereEngine / Hybrid System>2GD-FTV EMISSION CONTROL>EXHAUST FUEL ADDITION INJECTOR>REMOVAL


c.

Repair or replace the malfunctioning part confirmed in the diagnosis of the fuel injection system, intake/exhaust system and after treatment control system.


d.

Check for DTCs output in step 1.

Result:
Result Proceed to
DTC P244A is output A
DTC other than DTC P244A output B




A

20.READ VALUE USING GTS (DPF DIFFERENTIAL PRESSURE)

B

21.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
20.READ VALUE USING GTS (DPF DIFFERENTIAL PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / DPF Differential Pressure.

Powertrain > Engine > Data List
Tester Display
DPF Differential Pressure
50003 234 844

d.

Start the engine.


e.

Engine is running at 4000 rpm with no load for 10 seconds or more.


f.

Confirmation that the differential pressure is higher than 1.5 kPa.


Result:
Proceed to
NEXT



NEXT

END

21.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 234

d.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.


e.

Perform PM forced regeneration.

Click hereEngine / Hybrid System>2GD-FTV EMISSION CONTROL>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION

Result:

PM forced regeneration completes normally.



Result:
Proceed to
NEXT



NEXT

END

22.READ VALUE USING GTS (DPF DIFFERENTIAL PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / Diesel Exhaust / DPF Differential Pressure.


d.

Check the DPF Differential Pressure values from idle speed to unloaded maximum engine speed.

Powertrain > Engine > Data List
Tester Display
DPF Differential Pressure
50003 61 238
Result:
Result Proceed to
DPF Differential Pressure increases as engine speed increases from idle speed A
Except above B


A241154E04
3.313,3.375 3.542,3.375 3.542,3.375 3.719,3.875 false 4.25,4.281 4.125,4.281 false 4.125,4.281 3.854,3.979 false 4.146,4.927 4.042,4.927 4.042,4.927 3.833,4.76 false 0.469,1.479 1.74,1.865 1.271,0.385 10 Engine Speed (rpm) 0.833,2.99 1.74,3.375 0.906,0.385 10 MAF (gm/sec) 0.688,4.115 1.698,4.521 1.01,0.406 10 DPF Differential Pressure (kPa) 4.198,4.854 4.323,5 0.125,0.146 10 A 1.771,1.875 1.875,2.156 0.104,0.281 10 0 1.781,3.24 1.885,3.521 0.104,0.281 10 0 1.792,4.615 1.896,4.896 0.104,0.281 10 0 0.677,0.854 1.948,1.24 1.271,0.385 10 Unloaded Maximum Engine Speed 2.385,3.281 3.344,3.521 0.958,0.24 10 Normal Piping 4.313,4.208 5.271,4.448 0.958,0.24 10 Clogged Piping 2.313,5.417 5.333,5.698 3.021,0.281 10 Negative pressure occurs for approx. 1 second.

HINT:

If DPF Differential Pressure indicates negative pressure for approx. 1 second as shown in the illustration (A) when the engine speed increases, the differential pressure sensor piping of the DPF catalyst may be clogged.




A

25.CHECK FOR BLACK SMOKE

B

23.CHECK BLOCKAGE OF AIR HOSE AND VACUUM PIPE (DIFFERENTIAL PRESSURE SENSOR - VACUUM PIPE)
23.CHECK BLOCKAGE OF AIR HOSE AND VACUUM PIPE (DIFFERENTIAL PRESSURE SENSOR - VACUUM PIPE)
CAUTION:

Be careful of being burned by exhaust gases during the following inspection.


HINT:

Before checking the differential pressure sensor, perform a visual inspection of the differential pressure pipes and check that they are properly connected and no air is leaking from the pipes or hoses. If a malfunction is found, repair it before checking the sensor.


A360341C01
4.396,2.135 4.99,1.563 4.99,1.563 5.083,1.563 true 2.198,1.417 2.292,1.417 2.292,1.417 2.698,2.01 true 3.688,1.031 4.521,0.302 4.521,0.302 4.615,0.302 true 2.917,0.323 3.01,0.323 3.01,0.323 3.417,0.917 true 2.74,0.25 3.052,0.406 0.313,0.156 10 false *1 4.656,0.229 4.969,0.385 0.313,0.156 10 false *2 2.042,1.354 2.354,1.51 0.313,0.156 10 false *3 5.125,1.49 5.438,1.646 0.313,0.156 10 false *4
*1 Air Hose (Downstream) *2 Air Hose (Upstream)
*3 No. 2 Vacuum Pipe *4 No. 1 Vacuum Pipe


a.
A362182C03
0.615,0.958 1.667,1.302 true 0.625,0.958 1.323,0.844 false 0.458,0.885 0.771,1.042 0.313,0.156 10 false *1
*1 Air Hose


Disconnect the air hoses (both upstream and downstream) from the differential pressure sensor.


b.

Start the engine.


c.

Check if there are exhaust gas pulsations from both air hoses during idling.

OK:

Exhaust gas pulsation exists.



Result:
Proceed to
OK
NG



OK

24.REPLACE DIFFERENTIAL PRESSURE SENSOR

NG

27.REPAIR OR REPLACE NO. 1 VACUUM PIPE OR NO. 2 VACUUM PIPE
24.REPLACE DIFFERENTIAL PRESSURE SENSOR
a.

Result:
Proceed to
NEXT



NEXT

25.CHECK FOR BLACK SMOKE
25.CHECK FOR BLACK SMOKE
a.

Start the engine and drive the vehicle until the engine coolant temperature reaches 75°C (167°F) or higher.


b.

Stop the vehicle and allow the engine to idle.


c.

Fully depress the accelerator pedal for 5 seconds, and then release it [A].


d.

Repeat the procedure [A] 10 times [B].


e.

Check for black smoke emission during the procedures [A] and [B].

OK:

Black smoke is emitted less than 5 times.


HINT:

Even if the black smoke is very thin, count the number of black smoke emissions if there is any visible smoke.



Result:
Proceed to
OK
NG



OK

26.READ VALUE USING GTS (CATALYST DIFFERENTIAL PRESS)

NG

30.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY
26.READ VALUE USING GTS (CATALYST DIFFERENTIAL PRESS)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / Diesel Exhaust / Catalyst Differential Press.


d.

Check the value of Catalyst Differential Press at 4000 rpm without load.

Powertrain > Engine > Data List
Tester Display
Catalyst Differential Press
50003 61 608
Result:
Result Proceed to
Catalyst Differential Press is more than 0.45 A
Except above B




A

30.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

B

29.PERFORM PM FORCED REGENERATION
27.REPAIR OR REPLACE NO. 1 VACUUM PIPE OR NO. 2 VACUUM PIPE
a.

Repair or replace No. 1 vacuum pipe or No. 2 vacuum pipe.


Result:
Proceed to
NEXT



NEXT

28.READ VALUE USING GTS (DPF DIFFERENTIAL PRESSURE)
28.READ VALUE USING GTS (DPF DIFFERENTIAL PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / Diesel Exhaust / DPF Differential Pressure.


d.

Check the DPF Differential Pressure values from idle speed to unloaded maximum engine speed.

Powertrain > Engine > Data List
Tester Display
DPF Differential Pressure
50003 61 238
A241154E04
3.313,3.375 3.542,3.375 3.542,3.375 3.719,3.875 false 4.25,4.281 4.125,4.281 false 4.125,4.281 3.854,3.979 false 4.146,4.927 4.042,4.927 4.042,4.927 3.833,4.76 false 0.469,1.479 1.74,1.865 1.271,0.385 10 Engine Speed (rpm) 0.833,2.99 1.74,3.375 0.906,0.385 10 MAF (gm/sec) 0.688,4.115 1.698,4.521 1.01,0.406 10 DPF Differential Pressure (kPa) 4.198,4.854 4.323,5 0.125,0.146 10 A 1.771,1.875 1.875,2.156 0.104,0.281 10 0 1.781,3.24 1.885,3.521 0.104,0.281 10 0 1.792,4.615 1.896,4.896 0.104,0.281 10 0 0.677,0.854 1.948,1.24 1.271,0.385 10 Unloaded Maximum Engine Speed 2.385,3.281 3.344,3.521 0.958,0.24 10 Normal Piping 4.313,4.208 5.271,4.448 0.958,0.24 10 Clogged Piping 2.313,5.417 5.333,5.698 3.021,0.281 10 Negative pressure occurs for approx. 1 second.

HINT:

If DPF Differential Pressure indicates negative pressure for approx. 1 second as shown in the illustration (A) when the engine speed increases, the differential pressure sensor piping of the DPF catalyst may be clogged.


OK:

DPF Differential Pressure increases as engine speed increases from idle speed.


Result:
Proceed to
OK
NG




NG

24.REPLACE DIFFERENTIAL PRESSURE SENSOR

OK

25.CHECK FOR BLACK SMOKE
29.PERFORM PM FORCED REGENERATION
a.

Remove the EFI-B fuse or disconnect the cable from the battery terminal for 60 seconds or more, and then reinstall the EFI-B fuse or reconnect the cable to the battery terminal.

HINT:
·

The amount of built up particulate matter recorded by the ECM cannot be initialized by the GTS.

·

If the amount of built up particulate matter recorded by the ECM is not initialized, PM forced regeneration cannot be performed using the GTS.




b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 234

e.

Warm up the engine (engine coolant temperature is 75°C (167°F) or higher).


f.

Perform PM forced regeneration.

Click hereEngine / Hybrid System>2GD-FTV EMISSION CONTROL>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION

Result:

PM forced regeneration completes normally.



Result:
Proceed to
OK
NG



OK

END

NG

16.CHECK FUEL INJECTION SYSTEM
30.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY
a.

Even though it has been determined that the exhaust manifold converter sub-assembly needs to be replaced, make sure to perform all diagnostic procedures for DTC P244B before replacing it.


Result:
Proceed to
NEXT



NEXT

16.CHECK FUEL INJECTION SYSTEM