Home › Engine / Hybrid System › 2GD-FTV ENGINE CONTROL › ECD SYSTEM(w/ Urea SCR System) › from 2016.03
RM3250E _51 Engine / Hybrid System _038005 2GD-FTV ENGINE CONTROL _0262511 ECD SYSTEM(w/ Urea SCR System) C

2GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  P2263  Turbo/Super Charger Boost System Performance  


DESCRIPTION

After the ignition switch is turned off, the ECM performs nozzle vane plate soot removal control (current opening angle→fully opened→fully closed). Monitor the motor drive current value while these opening and closing operations are performed. If the value exceeds the threshold, it can be determined that movement is abnormal. If the system judges that abnormal movements have occurred twice, this DTC is stored, and a message is displayed on the multi-information display the next time the ignition switch is turned to ON.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2263 Turbo/Super Charger Boost System Performance During soot removal control of the nozzle vane plate after the ignition switch is turned off, DC motor operation current exceeds the threshold (2 trip detection logic). Abnormality in sliding movement of turbocharger nozzle vane plate -*
*: The multi-information display does illuminate.
DTC stored

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P2263 Turn the ignition switch off, and then perform turbocharger nozzle vane plate soot removal control.

PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (DTC P2263)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.


d.

Read DTCs.

Powertrain > Engine > Trouble Codes
50001 234
Result:
Result Proceed to
DTC P2263 is output A
DTC P2263 and other DTCs are output B




A

2.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VN TURBO CLEANING)

B

2.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VN TURBO CLEANING)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine and warm it up until the engine coolant temperature is 77°C (170°F) or higher with all the accessories switched off.


d.

Enter the following menus: Powertrain / Engine / Active Test / Activate the VN Turbo Cleaning.


e.

Perform the Active Test.

Powertrain > Engine > Active Test
Tester Display
Activate the VN Turbo Cleaning
50004 234 316
HINT:
·

VN turbo cleaning finishes 20 minutes after the speed increases.

·

If actions such as depressing the accelerator pedal or operating the shift lever are performed, cleaning control is stopped. If this occurs, it is necessary to perform the procedure again.




Result:
Proceed to
NEXT



NEXT

3.INSPECT COMBINATION METER DISPLAY (MULTI-INFORMATION DISPLAY)
3.INSPECT COMBINATION METER DISPLAY (MULTI-INFORMATION DISPLAY)
a.

Turn the ignition switch off and wait for at least 30 seconds.


b.

Turn the ignition switch to ON.


c.

Check the multi-information display.

Result:
Result Proceed to
Message displayed in multi-information display A
Message not displayed in multi-information display B




A

4.REPLACE TURBOCHARGER SUB-ASSEMBLY

B

5.CLEAR DTC
4.REPLACE TURBOCHARGER SUB-ASSEMBLY

Result:
Proceed to
NEXT



NEXT

5.CLEAR DTC
5.CLEAR DTC
a.

Turn the ignition switch off and wait for at least 30 seconds.


b.

Turn the ignition switch to ON.


c.

Check that a message is not displayed in the multi-information display.


d.

Connect the GTS to the DLC3.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes / Clear.


g.

Clear the DTC.

Powertrain > Engine > Clear DTCs
50002 234

Result:
Proceed to
NEXT



NEXT

END