Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM › from 2016.03
RM3250E _51 Engine / Hybrid System _053992 STOP AND START _0262513 STOP AND START SYSTEM U

STOP AND START  STOP AND START SYSTEM  TERMINALS OF ECU  


ENGINE STOP AND START ECU


A381876E01
3.052,0.115 3.552,0.427 0.5,0.313 4.948,0.115 5.448,0.427 0.5,0.313 1.438,0.115 1.938,0.427 0.5,0.313 0.604,1.958 1.104,2.271 0.5,0.313 2.688,1.958 3.188,2.271 0.5,0.313 5.438,1.969 5.938,2.281 0.5,0.313 0.688,2.042 1.302,2.24 0.615,0.198 10 false G125 1.51,0.208 2.125,0.406 0.615,0.198 10 false G125 3.135,0.219 3.75,0.417 0.615,0.198 10 false G126 5.031,0.219 5.646,0.417 0.615,0.198 10 false G127 5.531,2.052 6.146,2.25 0.615,0.198 10 false G127 2.781,2.042 3.396,2.24 0.615,0.198 10 false G126

a.

Disconnect the G125, G126 and G127 engine stop and start ECU connectors.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G125-1 (BIN2) - Body ground L - Body ground Battery Always 9.5 to 14 V
G125-2 (GND2) - Body ground W-B - Body ground Ground Always Below 1 Ω
G125-3 (BIN1) - Body ground R - Body ground Battery Always 9.5 to 14 V
G125-8 (GND1) - Body ground W-B - Body ground Ground Always Below 1 Ω
G126-1 (+B) - Body ground Y - Body ground Power source of engine stop and start ECU Ignition switch ON 9.5 to 14 V
G126-6 (DGND) - Body ground BR - Body ground Ground Always Below 1 Ω
G126-10 (NE) - Body ground SB - Body ground Engine speed signal from ECM Always 10 kΩ or higher
G127-13 (CANH) - Body ground P - Body ground CAN communication Always 200 Ω or higher
G127-14 (CANL) - Body ground W - Body ground CAN communication Always 200 Ω or higher
G127-18 (IG2) - Body ground Y - Body ground Ignition or starter switch assembly (w/o Entry and Start System) or push start switch assembly (w/ Entry and Start System) signal Ignition switch ON 9.5 to 14 V
G127-19 (ACC) - Body ground GR - Body ground Ignition or starter switch assembly (w/o Entry and Start System) or push start switch assembly (w/ Entry and Start System) signal Ignition switch ACC 9.5 to 14 V
G127-21 (IG1) - Body ground R - Body ground Ignition or starter switch assembly (w/o Entry and Start System) or push start switch assembly (w/ Entry and Start System) signal Ignition switch ON 9.5 to 14 V


c.

Reconnect the G125, G126 and G127 engine stop and start ECU connectors.


d.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition

*1: for Automatic Transmission

*2: for Manual Transmission

G126-3 (BRE2) - Body ground Y - Body ground Ground (vacuum sensor assembly) Always Below 1 Ω
G126-7 (BNT1) - G126-6 (DGND) Y - BR Engine hood courtesy switch (Hood lock assembly) signal
·

Ignition switch ON

·

Engine hood closed


0 to 1.5 V
·

Ignition switch ON

·

Engine hood open


8 to 14 V
G126-10 (NE) - G126-6 (DGND) SB - BR Engine speed signal from ECM Idling after engine warmed up Pulse generation
(see waveform 1)
G126-11 (CLU) - G126-6 (DGND)*2 P - BR Clutch switch assembly (for upper) signal
·

Ignition switch ON

·

Clutch pedal released


Below 1.5 V
·

Ignition switch ON

·

Clutch pedal fully depressed


8 to 14 V
G126-26 (TMVC) - G126-25 (TME2)*2 B - R Neutral position sensor (neutral position switch) power supply Ignition switch ON 4.5 to 5.5 V
G126-8 (TMN) - G126-25 (TME2)*2 LG - R Neutral position sensor (neutral position switch) signal
·

Ignition switch ON

·

Shift lever in neutral


2.7 to 4.3 V
·

Ignition switch ON

·

Shift lever in any other than neutral


0.7 to 1.9 V
G126-13 (PB) - G126-3 (BRE2) B - Y Vacuum sensor assembly signal
·

Ignition switch ON

·

Absolute pressure of 40 kPa (300 mmHg, 11.8 in.Hg) applied to vacuum sensor assembly


1.6 to 2.0 V
·

Ignition switch ON

·

Absolute pressure of 60 kPa (450 mmHg, 17.7 in.Hg) applied to vacuum sensor assembly


2.2 to 2.6 V
·

Ignition switch ON

·

Atmospheric pressure applied to vacuum sensor assembly


3.4 to 3.8 V
G126-14 (BRVC) - G126-6 (DGND) P - BR Vacuum sensor assembly power supply
·

Ignition switch ON

·

Engine stopped


4.5 to 5.5 V
G126-17 (CLL) - G126-6 (DGND) L - BR Park/neutral position switch assembly signal*1
·

Ignition switch ON

·

Shift lever not in P or N


8 to 14 V
·

Ignition switch ON

·

Shift lever in P or N


Below 3.0 V
Clutch start switch assembly (for lower) signal*2
·

Ignition switch ON

·

Clutch pedal released


8 to 14 V
·

Ignition switch ON

·

Clutch pedal fully depressed


Below 1.5 V
G126-21 (STA) - G126-6 (DGND) G - BR Starter pinion operation signal Cranking 6.0 V or more
G126-23 (STA2) - G126-6 (DGND) GR - BR Starter motor operation signal Cranking 6.0 V or more
G127-1 (IG31) - G126-6 (DGND) L - BR Backup boost converter signal Ignition switch ON 10.5 to 16 V
G127-3 (IG41) - G126-6 (DGND) L - BR Backup boost converter signal Ignition switch ON 10.5 to 16 V
G127-5 (ECAN) - G126-6 (DGND) V - BR Stop and start system cancel switch (ecorun cancel switch assembly) signal
·

Ignition switch ON

·

Stop and start system cancel switch (ecorun cancel switch assembly) push and held


0 to 1.5 V
·

Ignition switch ON

·

Stop and start system cancel switch (ecorun cancel switch assembly) not pressed


8 to 14 V
G127-8 (EGND) - G125-8 (GND1)*1 R - W-B Electromagnetic oil pump directions signal Either of the following conditions is met:
·

Engine stopped by stop and start control

·

Ignition switch ON (engine not running) and Active Test "Electromagnetic Oil Pump" being performed


Pulse generation
(see waveform 2)
G127-9 (EMOP) - G125-8 (GND1)*1 W - W-B Electromagnetic oil pump directions signal Either of the following conditions is met:
·

Engine stopped by stop and start control

·

Ignition switch ON (engine not running) and Active Test "Electromagnetic Oil Pump" being performed


Pulse generation
(see waveform 2)
G127-10 (IG12) - G126-6 (DGND) Y - BR Backup boost converter signal Ignition switch ON 10.5 to 16 V
G127-12 (B42) - G126-6 (DGND) SB - BR Backup boost converter signal Always 10.5 to 16 V
G127-15 (AC42) - G126-6 (DGND) GR - BR Backup boost converter signal Ignition switch ACC 10.5 to 16 V
G127-18 (IG2) - G126-6 (DGND) Y - BR Ignition or starter switch assembly (w/o Entry and Start System) or push start switch assembly (w/ Entry and Start System) signal Ignition switch ACC Below 1 V
Ignition switch ON 9.5 to 14 V
G127-19 (ACC) - G126-6 (DGND) GR - BR Ignition or starter switch assembly (w/o Entry and Start System) or push start switch assembly (w/ Entry and Start System) signal Ignition switch off Below 1 V
Ignition switch ACC 9.5 to 14 V
G127-21 (IG1) - G126-6 (DGND) R - BR Ignition or starter switch assembly (w/o Entry and Start System) or push start switch assembly (w/ Entry and Start System) signal Ignition switch ACC Below 1 V
Ignition switch ON 9.5 to 14 V


e.
A346371E01
2.802,1.01 3.26,1.208 0.458,0.198 10 false GND 0.271,0.104 1.5,0.302 1.229,0.198 10 false 5 V/DIV. 1.406,1.906 2.781,2.104 1.375,0.198 10 false 2 ms./DIV.

Waveform 1

Item Content
Tester Connection G126-10 (NE) - G126-6 (DGND)
Tool Setting 5 V/DIV., 2 ms./DIV.
Condition Idling after engine warmed up


f.
A345972E01
0.115,0.115 1.49,0.313 1.375,0.198 10 false 10 V/DIV. 1.281,1.896 2.052,2.094 0.771,0.198 10 false 20 ms./DIV. 0.115,1.396 0.573,1.594 0.458,0.198 10 false GND 0.219,1.135 0.531,1.333 0.313,0.198 10 false +B 0.104,0.875 0.719,1.073 0.615,0.198 10 false 43 V

Waveform 2

Item Content
Tester Connection G127-8 (EGND) - G125-8 (GND1)
G127-9 (EMOP) - G125-8 (GND1)
Tool Setting 10 V/DIV., 20 ms./DIV.
Condition Either of the following conditions is met:
·

Engine stopped by stop and start control

·

Ignition switch ON (engine not running) and Active Test "Electromagnetic Oil Pump" being performed