Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU) › from 2016.03
RM3250E _57 Power Source / Network _038063 NETWORKING _0262514 CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)  Navigation ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Navigation ECU Communication Stop Mode Either condition is met:
·

Communication stop for "Display and Navigation (AVN1)" is indicated on the "Communication Bus Check" screen of the GTS.

(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Navigation ECU Communication Stop Mode" in "DTC Combination Table".

(Click here)


·

Power source circuit of navigation receiver assembly

·

Navigation receiver assembly ground circuit

·

Navigation receiver assembly CAN branch wire or connector

·

Navigation receiver assembly



WIRING DIAGRAM

C348061E01
0.104,1.844 2.177,2.167 2.073,0.323 10 false No. 4 CAN Junction Connector 0.094,1.677 2.167,2 2.073,0.323 10 false G132 1.708,0.698 1.99,0.948 0.281,0.25 10 false 1 1.729,1.271 2.01,1.521 0.281,0.25 10 false 2 5.125,0.844 5.74,1.042 0.615,0.198 10 false G113 5.125,1.438 5.74,1.635 0.615,0.198 10 false G113 5.24,0.563 5.521,0.813 0.281,0.25 10 false 9 5.188,1.177 5.469,1.427 0.281,0.25 10 false 10 5.667,0.865 6.281,1.063 0.615,0.198 10 false CANH 5.677,1.427 6.292,1.625 0.615,0.198 10 false CANL 5.677,2.615 6.292,2.813 0.615,0.198 10 false +B1 5.688,3.927 6.302,4.125 0.615,0.198 10 false IG 5.688,4.813 6.302,5.01 0.615,0.198 10 false ACC1 5.677,6.208 6.292,6.406 0.615,0.198 10 false GND1 5.135,2.615 5.75,2.813 0.615,0.198 10 false G115 5.125,3.927 5.74,4.125 0.615,0.198 10 false G113 5.125,4.813 5.74,5.01 0.615,0.198 10 false G115 5.135,6.198 5.75,6.396 0.615,0.198 10 false G115 4.042,2.438 4.865,2.76 0.823,0.323 10 false RADIO 3.979,3.74 4.802,4.063 0.823,0.323 10 false IG1 NO.4 4.115,4.604 4.938,4.927 0.823,0.323 10 false ACC 2.104,2.604 3.031,2.906 0.927,0.302 10 false from Battery 0.396,3.927 3.26,4.271 2.865,0.344 10 false from IG1 NO.1 Relay*1, Ignition Switch*2 1.875,4.802 3.469,5.219 1.594,0.417 10 false from ACC Relay 0.229,6.135 3.094,6.479 2.865,0.344 10 false *1: w/ Entry and Start System 0.24,6.521 3.104,6.865 2.865,0.344 10 false *2: w/o Entry and Start System 0.24,6.896 3.104,7.24 2.865,0.344 10 false *3: w/o Stop and Start System 0.229,7.26 3.094,7.604 2.865,0.344 10 false *4: w/ Stop and Start System 0.74,3.281 3.031,3.615 2.292,0.333 10 false from Engine Stop and Start ECU*4 0.76,5.49 3.052,5.823 2.292,0.333 10 false from Engine Stop and Start ECU*4 3.438,5.333 3.75,5.531 0.313,0.198 10 false *4 3.417,4.656 3.729,4.854 0.313,0.198 10 false *3 3.448,3.115 3.76,3.313 0.313,0.198 10 false *4 3.417,2.448 3.729,2.646 0.313,0.198 10 false *3 5.031,7.135 7.031,7.448 2,0.313 10 false Navigation Receiver Assembly 5.25,2.292 5.521,2.531 0.271,0.24 10 false 4 5.25,3.594 5.521,3.833 0.271,0.24 10 false 1 5.271,4.479 5.542,4.719 0.271,0.24 10 false 3 5.271,5.865 5.542,6.104 0.271,0.24 10 false 7

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 31 seconds.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

·

When replacing the navigation receiver assembly, it is necessary to perform the vehicle contract setting for Connected Services.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (NAVIGATION RECEIVER ASSEMBLY CAN BRANCH WIRE)
a.
C310966C10
1.49,0.198 1.938,0.469 0.448,0.271 1.104,1.75 1.271,1.75 1.271,1.75 1.896,1.104 true 2.365,1.76 2.219,1.76 2.219,1.76 2.021,1.115 true 0.135,0.115 0.448,0.271 0.313,0.156 10 false *a 1.563,0.24 2.177,0.438 0.615,0.198 10 false G113 0.656,1.656 1.271,1.854 0.615,0.198 10 false CANH 2.427,1.667 3.042,1.865 0.615,0.198 10 false CANL
*a Front view of wire harness connector
(to Navigation Receiver Assembly)


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the navigation receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G113-9 (CANH) - G113-10 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result Proceed to
OK (w/o Stop and Start System) A
OK (w/ Stop and Start System) B
NG C



A

2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)

B

3.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)

C

REPAIR OR REPLACE NAVIGATION RECEIVER ASSEMBLY CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)
a.
C277477C22
1.5,0.208 1.938,0.448 0.438,0.24 1.542,1.813 2.01,2.052 0.469,0.24 0.979,2.604 0.802,2.396 0.802,2.396 0.635,2.396 true 2.104,1.479 1.854,1.479 1.854,1.479 1.667,1.146 true 2.573,0.708 2.375,0.708 2.375,0.708 2.198,0.896 true 2.438,0.396 2.24,0.396 2.24,0.396 2,0.885 true 0.448,2.302 0.906,2.5 0.458,0.198 10 false IG 2.146,1.396 2.688,1.625 0.542,0.229 10 false GND1 0.125,0.135 0.583,0.333 0.458,0.198 10 false *a 1.563,0.229 2.021,0.427 0.458,0.198 10 false G115 1.615,1.833 2.073,2.031 0.458,0.198 10 false G113 2.615,0.604 3.156,0.833 0.542,0.229 10 false +B1 2.469,0.292 3.01,0.521 0.542,0.229 10 false ACC1
*a Front view of wire harness connector
(to Navigation Receiver Assembly)


Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



b.

Disconnect the navigation receiver assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G115-4 (+B1) - Body ground Always 11 to 14 V
G113-1 (IG) - Body ground Ignition switch ON 11 to 14 V
G115-3 (ACC1) - Body ground Ignition switch ACC 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G115-7 (GND1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)
a.
C277477C22
1.5,0.208 1.938,0.448 0.438,0.24 1.542,1.813 2.01,2.052 0.469,0.24 0.979,2.604 0.802,2.396 0.802,2.396 0.635,2.396 true 2.104,1.479 1.854,1.479 1.854,1.479 1.667,1.146 true 2.573,0.708 2.375,0.708 2.375,0.708 2.198,0.896 true 2.438,0.396 2.24,0.396 2.24,0.396 2,0.885 true 0.448,2.302 0.906,2.5 0.458,0.198 10 false IG 2.146,1.396 2.688,1.625 0.542,0.229 10 false GND1 0.125,0.135 0.583,0.333 0.458,0.198 10 false *a 1.563,0.229 2.021,0.427 0.458,0.198 10 false G115 1.615,1.833 2.073,2.031 0.458,0.198 10 false G113 2.615,0.604 3.156,0.833 0.542,0.229 10 false +B1 2.469,0.292 3.01,0.521 0.542,0.229 10 false ACC1
*a Front view of wire harness connector
(to Navigation Receiver Assembly)


Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



b.

Disconnect the navigation receiver assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G115-4 (+B1) - Body ground Always 10.5 to 16 V
G113-1 (IG) - Body ground Ignition switch ON 11 to 14 V
G115-3 (ACC1) - Body ground Ignition switch ACC 10.5 to 16 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G115-7 (GND1) - Body ground Always Below 1 Ω



Result:
Result Proceed to
OK A
NG (+B1, ACC1 terminal) B
NG (IG, GND1 terminal) C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR