Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU) › from 2016.03
RM3250E _57 Power Source / Network _038063 NETWORKING _0262514 CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)  Check Bus 5 Lines for Short Circuit  


DESCRIPTION

There may be a short circuit between the bus 5 CAN main wires and/or CAN branch wires when the resistance between terminals 15 (CA5H) and 16 (CA5L) of the central gateway ECU (network gateway ECU) is below 54 Ω.

Detection Item Trouble Area
Resistance between terminals 15 (CA5H) and 16 (CA5L) of central gateway ECU (network gateway ECU) is below 54 Ω.
·

Short in bus 5 CAN main wires

·

Short in bus 5 CAN branch wires

·

Central gateway ECU (network gateway ECU)

·

Forward recognition camera

·

Millimeter wave radar sensor assembly

·

No. 3 CAN junction connector



WIRING DIAGRAM

C348062E01
6.083,0.688 6.698,0.885 0.615,0.198 10 false CA5H 6.094,1.438 6.708,1.635 0.615,0.198 10 false CA5L 6.104,4.354 6.719,4.552 0.615,0.198 10 false CAXH 6.115,5.177 6.729,5.375 0.615,0.198 10 false CAXL 5.74,0.688 6.052,0.885 0.313,0.198 10 false 15 5.74,1.146 6.052,1.344 0.313,0.198 10 false 16 5.813,4.385 6.125,4.583 0.313,0.198 10 false 9 5.729,4.854 6.042,5.052 0.313,0.198 10 false 24 5.177,5.521 5.792,5.719 0.615,0.198 10 false G128 5.198,5.677 7.156,6.156 1.958,0.479 10 false Central Gateway ECU (Network Gateway ECU) 2.823,5.698 4.906,5.958 2.083,0.26 10 false No. 3 CAN Junction Connector 2.802,5.542 3.417,5.74 0.615,0.198 10 false G131 4.51,0.667 4.823,0.865 0.313,0.198 10 false 6 4.49,1.125 4.802,1.323 0.313,0.198 10 false 16 4.521,4.354 4.833,4.552 0.313,0.198 10 false 7 4.479,4.833 4.792,5.031 0.313,0.198 10 false 17 3.042,1.042 3.354,1.24 0.313,0.198 10 false 4 2.969,1.573 3.281,1.771 0.313,0.198 10 false 14 3.052,3.438 3.365,3.635 0.313,0.198 10 false 5 3,3.969 3.313,4.167 0.313,0.198 10 false 15 1.729,1.052 2.042,1.25 0.313,0.198 10 false 5 1.708,1.563 2.021,1.76 0.313,0.198 10 false 11 1.729,3.448 2.042,3.646 0.313,0.198 10 false 3 1.729,3.979 2.042,4.177 0.313,0.198 10 false 2 1.177,1.219 1.792,1.417 0.615,0.198 10 false CA1P 1.188,1.75 1.802,1.948 0.615,0.198 10 false CA1N 1.177,3.604 1.792,3.802 0.615,0.198 10 false CA2H 1.198,4.125 1.813,4.323 0.615,0.198 10 false CA2L 0.208,2.198 2.292,2.458 2.083,0.26 10 false Forward Recognition Camera 0.229,4.563 2.135,4.948 1.906,0.385 10 false Millimeter Wave Radar Sensor Assembly 0.208,2.042 2.292,2.302 2.083,0.26 10 false Q4 0.229,4.375 2.135,4.76 1.906,0.385 10 false A64

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.

C348056C03
3.323,0.552 3.875,0.875 0.552,0.323 3.198,1.385 2.844,0.698 2.844,0.698 2.594,0.698 true 3.208,1.573 2.802,2.219 2.802,2.219 2.552,2.219 true 3.417,1.594 2.938,2.448 2.938,2.448 2.688,2.448 true 3.802,1.396 4.521,0.406 4.521,0.406 4.771,0.406 true 3.771,1.583 4.49,2.344 4.49,2.344 4.74,2.344 true 3.385,1.406 3,0.521 3,0.521 2.75,0.521 true 4,1.406 4.594,0.625 4.594,0.625 4.844,0.625 true 3.99,1.563 4.635,2.125 4.635,2.125 4.885,2.125 true 0.135,0.094 0.448,0.292 0.313,0.198 10 false *a 3.438,0.635 3.896,0.833 0.458,0.198 10 false G131 2.021,0.635 2.938,0.833 0.917,0.198 10 false CANH*b 2.219,0.438 3.135,0.635 0.917,0.198 10 false CANH*c 4.802,0.333 5.719,0.531 0.917,0.198 10 false CANH*d 4.885,0.552 5.802,0.75 0.917,0.198 10 false CANH*d 2.021,2.125 2.938,2.323 0.917,0.198 10 false CANL*b 2.167,2.365 3.083,2.563 0.917,0.198 10 false CANL*c 4.792,2.271 5.708,2.469 0.917,0.198 10 false CANL*d 4.927,2.052 5.844,2.25 0.917,0.198 10 false CANL*d
*a Front view of wire harness connector
(to No. 3 CAN Junction Connector)
*b to Forward Recognition Camera
*c to Millimeter Wave Radar Sensor Assembly *d to Central Gateway ECU (Network Gateway ECU)



b.

Disconnect the No. 3 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to
G131-4 (CANH) - G131-14 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Forward recognition camera
G131-5 (CANH) - G131-15 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Millimeter wave radar sensor assembly
G131-6 (CANH) - G131-16 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU)
G131-7 (CANH) - G131-17 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK A
NG (Central gateway ECU [network gateway ECU] CAN main wire) B
NG (ECU or sensor CAN branch wires) C



A

REPLACE NO. 3 CAN JUNCTION CONNECTOR

B

2.CONNECT CONNECTOR

C

4.CHECK FOR SHORT IN CAN BUS WIRES (ECU, SENSOR)
2.CONNECT CONNECTOR
a.

Reconnect the G131 No. 3 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

3.CHECK FOR SHORT IN CAN BUS WIRES (CENTRAL GATEWAY ECU)
3.CHECK FOR SHORT IN CAN BUS WIRES (CENTRAL GATEWAY ECU)
a.
C343190C70
0.104,1.115 0.583,1.417 0.479,0.302 0.802,1.771 0.948,1.771 0.948,1.771 1.469,1.281 true 0.917,1.979 1.063,1.979 1.063,1.979 1.563,1.292 true 1.927,1.99 2.073,1.99 2.073,1.99 2.573,1.302 true 1.781,0.417 1.927,0.417 1.927,0.417 2.458,1.094 true 0.177,1.188 0.792,1.385 0.615,0.198 10 false G128 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 0.396,1.688 1.01,1.885 0.615,0.198 10 false CA5H 0.5,1.906 1.115,2.104 0.615,0.198 10 false CA5L 1.365,0.333 1.979,0.531 0.615,0.198 10 false CAXH 1.552,1.906 2.167,2.104 0.615,0.198 10 false CAXL
*a Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU])


Disconnect the central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G128-15 (CA5H) - G128-16 (CA5L) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G128-9 (CAXH) - G128-24 (CAXL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CENTRAL GATEWAY ECU - NO. 3 CAN JUNCTION CONNECTOR)

4.CHECK FOR SHORT IN CAN BUS WIRES (ECU, SENSOR)
a.
C334654C05
1.469,0.26 1.969,0.51 0.5,0.25 2.646,1.667 2.479,1.667 2.479,1.667 1.938,1.125 true 2.49,1.927 2.323,1.927 2.323,1.927 1.844,1.125 true 0.104,0.083 0.458,0.396 0.354,0.313 10 false *a 1.542,0.313 2.021,0.625 0.479,0.313 10 false G128 2.573,1.844 3.156,2.073 0.583,0.229 10 false CA5L 2.729,1.583 3.313,1.813 0.583,0.229 10 false CA5H
*a Component with harness connected
(Central Gateway ECU [Network Gateway ECU])


Reconnect the CAN junction connector.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the short circuited CAN branch wire is connected.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G128-15 (CA5H) - G128-16 (CA5L) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


HINT:

If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.



Result:
Proceed to
OK
NG



OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR CAN BRANCH WIRES OR CONNECTOR