Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU) › from 2016.03
RM3250E _57 Power Source / Network _038063 NETWORKING _0262514 CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)  Millimeter Wave Radar Sensor Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Millimeter Wave Radar Sensor Communication Stop Mode Either condition is met:
·

Communication stop for "Front Radar" is indicated on the "Communication Bus Check" screen of the GTS.

(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Millimeter Wave Radar Sensor Communication Stop Mode" in "DTC Combination Table".

(Click here)


·

Power source or inside of millimeter wave radar sensor assembly

·

Millimeter wave radar sensor assembly ground circuit

·

Millimeter wave radar sensor assembly CAN branch wire or connector

·

Millimeter wave radar sensor assembly



WIRING DIAGRAM

C329326E12
1.552,0.885 2.042,1.354 0.49,0.469 10 false 5 1.531,1.406 2.021,1.875 0.49,0.469 10 false 15 0.094,1.802 0.667,1.99 0.573,0.188 10 false G131 0.104,1.979 2.083,2.271 1.979,0.292 10 false No. 3 CAN Junction Connector 5.427,0.875 5.917,1.344 0.49,0.469 10 false 3 5.427,1.406 5.917,1.875 0.49,0.469 10 false 2 4.063,2.281 5.104,2.479 1.042,0.198 10 false IG1 NO.5 5.396,2.333 5.885,2.802 0.49,0.469 10 false 8 5.656,2.448 6.146,2.917 0.49,0.469 10 false IGB 5.396,3.698 5.885,4.167 0.49,0.469 10 false 1 5.646,3.813 6.292,4.219 0.646,0.406 10 false SGND 5.094,4.771 5.583,5.063 0.49,0.292 10 false A64 5.104,4.958 6.979,5.354 1.875,0.396 10 false Millimeter Wave Radar Sensor Assembly 3.5,3.115 3.99,3.583 0.49,0.469 10 false *2 0.927,3.26 3.135,3.594 2.208,0.333 10 false from Engine Stop and Start ECU*2 1.625,2.458 3.333,2.813 1.708,0.354 10 false from IG1 NO.2 Relay*1 0.417,4.896 2.979,5.323 2.563,0.427 10 false *1: w/o Stop and Start System 3.479,2.333 3.969,2.802 0.49,0.469 10 false *1 0.417,5.229 2.76,5.604 2.344,0.375 10 false *2: w/ Stop and Start System 5.656,0.99 6.208,1.354 0.552,0.365 10 false CA2H 5.646,1.5 6.188,1.844 0.542,0.344 10 false CA2L

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Drive the vehicle at a speed of 5 km/h (approximately 4 mph) or more for 7 seconds or more.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (MILLIMETER WAVE RADAR SENSOR ASSEMBLY CAN BRANCH WIRE)
a.
C333439C65
1.49,0.135 1.979,0.354 0.49,0.219 1.792,1.031 1.125,0.479 1.125,0.479 0.99,0.479 true 1.625,1.042 0.885,0.719 0.885,0.719 0.75,0.719 true 0.073,0.094 0.385,0.25 0.313,0.156 10 false *a 1.635,0.177 2.188,0.469 0.552,0.292 10 false A64 0.563,0.375 1.177,0.573 0.615,0.198 10 false CA2H 0.344,0.615 0.958,0.813 0.615,0.198 10 false CA2L
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the millimeter wave radar sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A64-3 (CA2H) - A64-2 (CA2L) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result Proceed to
OK (w/o Stop and Start System) A
OK (w/ Stop and Start System) B
NG C



A

2.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - BATTERY AND BODY GROUND)

B

3.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - BATTERY AND BODY GROUND)

C

REPAIR OR REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY CAN BRANCH WIRE OR CONNECTOR (CA2H, CA2L)

2.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - BATTERY AND BODY GROUND)
a.
C333439C66
1.51,0.156 2,0.375 0.49,0.219 1.958,1.229 2.396,1.76 2.396,1.76 2.583,1.76 true 1.479,1.042 1.031,0.583 1.031,0.583 0.896,0.583 true 0.073,0.094 0.385,0.25 0.313,0.156 10 false *a 1.656,0.177 2.229,0.531 0.573,0.354 10 false A64 2.625,1.656 3.052,1.917 0.427,0.26 10 false IGB 0.458,0.5 0.948,0.75 0.49,0.25 10 false SGND
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A64-8 (IGB) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A64-1 (SGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - BATTERY AND BODY GROUND)
a.
C333439C66
1.51,0.156 2,0.375 0.49,0.219 1.958,1.229 2.396,1.76 2.396,1.76 2.583,1.76 true 1.479,1.042 1.031,0.583 1.031,0.583 0.896,0.583 true 0.073,0.094 0.385,0.25 0.313,0.156 10 false *a 1.656,0.177 2.229,0.531 0.573,0.354 10 false A64 2.625,1.656 3.052,1.917 0.427,0.26 10 false IGB 0.458,0.5 0.948,0.75 0.49,0.25 10 false SGND
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A64-8 (IGB) - Body ground Ignition switch ON 10.5 to 16 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A64-1 (SGND) - Body ground Always Below 1 Ω



Result:
Result Proceed to
OK A
NG (IGB terminal) B
NG (SGND terminal) C



A

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR