Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU) › from 2016.03
RM3250E _57 Power Source / Network _038063 NETWORKING _0262514 CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)  Open in Bus 3 Main Bus Line  


DESCRIPTION

There may be an open circuit in one of the bus 3 CAN main wires when the resistance between terminals 6 (CA3H) and 21 (CA3L) of the central gateway ECU (network gateway ECU) is 70 Ω or higher.

Symptom Trouble Area
Resistance between terminals 6 (CA3H) and 21 (CA3L) of central gateway ECU (network gateway ECU) is 70 Ω or higher.
·

CAN main wire or connector

·

Central gateway ECU (network gateway ECU)

·

No. 4 CAN junction connector



This malfunction is not related to the lines of a CAN branch or to ECUs or sensors connected to a CAN branch.

WIRING DIAGRAM

C348066E01
0.177,3.656 2.177,3.927 2,0.271 10 false No. 4 CAN Junction Connector 4.927,3.823 6.885,4.24 1.958,0.417 10 false Central Gateway ECU (Network Gateway ECU) 4.917,3.646 5.531,3.844 0.615,0.198 10 false G128 5.677,0.583 6.292,0.781 0.615,0.198 10 false CA3H 5.688,1.302 6.302,1.5 0.615,0.198 10 false CA3L 5.677,2.563 6.292,2.76 0.615,0.198 10 false CAYH 5.729,3.344 6.344,3.542 0.615,0.198 10 false CAYL 5.313,1.021 5.625,1.219 0.313,0.198 10 false 21 5.375,0.563 5.688,0.76 0.313,0.198 10 false 6 5.313,2.552 5.625,2.75 0.313,0.198 10 false 19 5.323,3.031 5.635,3.229 0.313,0.198 10 false 20 1.771,0.698 2.385,0.896 0.615,0.198 10 false G135 1.771,1.167 2.385,1.365 0.615,0.198 10 false G135 1.771,2.708 2.385,2.906 0.615,0.198 10 false G133 1.771,3.177 2.385,3.375 0.615,0.198 10 false G133 1.917,0.427 2.229,0.625 0.313,0.198 10 false 1 1.917,0.917 2.229,1.115 0.313,0.198 10 false 2 1.927,2.958 2.24,3.156 0.313,0.198 10 false 2 1.917,2.448 2.229,2.646 0.313,0.198 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU)
a.

Disconnect the cable from the negative (-) battery terminal.

C348057C02
3.813,0.25 4.25,0.531 0.438,0.281 5,0.25 5.438,0.531 0.438,0.281 4.052,1.167 4.052,0.531 true 5.167,1.167 5.167,0.531 true 5.094,3.417 5.385,3.802 5.385,3.802 5.521,3.802 true 5.125,3.24 5.365,2.927 5.365,2.927 5.5,2.927 true 0.073,0.094 0.438,0.354 0.365,0.26 10 false *1 2.24,1.948 2.854,2.146 0.615,0.198 10 false G135 2.24,2.833 2.854,3.031 0.615,0.198 10 false G133 3.865,0.323 4.479,0.521 0.615,0.198 10 false G135 5.052,0.323 5.667,0.521 0.615,0.198 10 false G133 4.125,2.625 4.438,2.823 0.313,0.198 10 false *a 5.573,2.854 6.188,3.052 0.615,0.198 10 false CANH 5.583,3.729 6.198,3.927 0.615,0.198 10 false CANL
*1 No. 4 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 4 CAN Junction Connector)
- -



b.

Disconnect the No. 4 CAN junction connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G133-1 (CANH) - G133-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
G135-1 (CANH) - G135-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 4 CAN JUNCTION CONNECTOR

NG

2.CONNECT CONNECTOR
2.CONNECT CONNECTOR
a.

Reconnect the No. 4 CAN junction connectors.


Result:
Proceed to
NEXT



NEXT

3.CHECK FOR OPEN IN CAN BUS WIRE (CENTRAL GATEWAY ECU)
3.CHECK FOR OPEN IN CAN BUS WIRE (CENTRAL GATEWAY ECU)
a.
C343190C71
0.104,1.115 0.583,1.417 0.479,0.302 1.188,1.771 1.333,1.771 1.333,1.771 1.854,1.281 true 1.323,1.979 1.469,1.979 1.469,1.979 1.969,1.292 true 2.458,1.927 2.302,1.927 2.302,1.927 2.073,1.292 true 1.781,0.417 1.927,0.417 1.927,0.417 2.115,1.094 true 0.177,1.188 0.792,1.385 0.615,0.198 10 false G128 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 0.76,1.688 1.375,1.885 0.615,0.198 10 false CAYH 0.927,1.906 1.542,2.104 0.615,0.198 10 false CAYL 1.365,0.333 1.979,0.531 0.615,0.198 10 false CA3H 2.51,1.865 3.125,2.063 0.615,0.198 10 false CA3L
*a Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU])


Disconnect the central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G128-6 (CA3H) - G128-21 (CA3L) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G128-19 (CAYH) - G128-20 (CAYL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CENTRAL GATEWAY ECU - NO. 4 CAN JUNCTION CONNECTOR)