Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD without Central Gateway ECU) › from 2016.03
RM3250E _57 Power Source / Network _038063 NETWORKING _0262515 CAN COMMUNICATION SYSTEM(for LHD without Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD without Central Gateway ECU)  4WD Control ECU Communication Stop Mode  


DESCRIPTION

Detection Item Detection Item Trouble Area
4WD Control ECU Communication Stop Mode Either condition is met:
·

"Four Wheel Drive Control" is not displayed on the "CAN Bus Check".

(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "4WD Control ECU Communication Stop Mode" in "DTC Combination Table".

(Click here)


·

Power source circuit of 4 wheel drive control ECU

·

4 wheel drive control ECU ground circuit

·

4 wheel drive control ECU CAN branch wire or connector

·

4 wheel drive control ECU



WIRING DIAGRAM

C317102E04
5.604,0.823 6.219,1.021 0.615,0.198 10 false CANH 5.604,1.302 6.219,1.5 0.615,0.198 10 false CANL 5.615,2.563 6.229,2.76 0.615,0.198 10 false +B 5.625,3.531 6.24,3.729 0.615,0.198 10 false IG 5.625,4.635 6.24,4.833 0.615,0.198 10 false GND 5.229,0.813 5.688,1.01 0.458,0.198 10 false C39 5.229,1.292 5.688,1.49 0.458,0.198 10 false C39 5.219,2.573 5.677,2.771 0.458,0.198 10 false C39 5.229,3.531 5.688,3.729 0.458,0.198 10 false C40 5.229,4.635 5.688,4.833 0.458,0.198 10 false C40 5.271,0.583 5.583,0.781 0.313,0.198 10 false 20 5.281,1.073 5.594,1.271 0.313,0.198 10 false 40 5.281,2.333 5.594,2.531 0.313,0.198 10 false 21 5.313,3.302 5.625,3.5 0.313,0.198 10 false 4 5.26,4.396 5.573,4.594 0.313,0.198 10 false 10 3.615,2.354 4.688,2.552 1.073,0.198 10 false 4WD-ALT 3.625,3.302 4.698,3.5 1.073,0.198 10 false 4WD-IG 1.396,3.531 2.771,3.792 1.375,0.26 10 false from IG1 NO.2 Relay 1.906,2.542 2.74,2.802 0.833,0.26 10 false from Battery 5.302,5.094 7.104,5.344 1.802,0.25 10 false 4 Wheel Drive Control ECU 1.688,0.667 2,0.865 0.313,0.198 10 false 4 1.688,1.167 2,1.365 0.313,0.198 10 false 14 0.146,1.708 2.594,2.177 2.448,0.469 10 false No. 2 CAN Junction Connector 0.135,1.542 0.635,1.979 0.5,0.438 10 false G68

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD without Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 2.2 seconds.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD without Central Gateway ECU)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (4 WHEEL DRIVE CONTROL ECU CAN BRANCH WIRE)
a.
C317101C02
1.5,0.177 1.917,0.458 0.417,0.281 2.906,1.021 2.771,0.385 2.771,0.385 2.625,0.385 true 2.604,1.823 2.76,1.823 2.76,1.823 2.906,1.292 true 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 1.573,0.229 2.031,0.427 0.458,0.198 10 false C39 2.188,0.292 2.802,0.49 0.615,0.198 10 false CANH 2.219,1.74 2.833,1.938 0.615,0.198 10 false CANL
*a Front view of wire harness connector
(to 4 Wheel Drive Control ECU)


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the 4 wheel drive control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C39-20 (CANH) - C39-40 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE 4 WHEEL DRIVE CONTROL ECU CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

2.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - BATTERY AND BODY GROUND)
a.
C325480C04
1.521,0.365 1.927,0.615 0.406,0.25 1.427,2.292 1.792,2.542 0.365,0.25 0.521,1.458 0.969,1.927 0.969,1.927 1.135,1.927 true 2.354,3.146 2.625,2.729 2.625,2.729 2.771,2.729 true 2.302,3.573 2.708,4.25 2.708,4.25 2.854,4.25 true 0.094,0.073 0.406,0.271 0.313,0.198 10 false *a 1.604,0.406 2.063,0.604 0.458,0.198 10 false C39 1.49,2.333 1.948,2.531 0.458,0.198 10 false C40 1.188,1.896 1.5,2.094 0.313,0.198 10 false +B 2.865,2.594 3.177,2.792 0.313,0.198 10 false IG 2.906,4.177 3.219,4.375 0.313,0.198 10 false GND
*a Front view of wire harness connector
(to 4 Wheel Drive Control ECU)


Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



b.

Disconnect the 4 wheel drive control ECU connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C39-21 (+B) - Body ground Always 11 to 14 V
C40-4 (IG) - Body ground Ignition switch ON 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C40-10 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE 4 WHEEL DRIVE CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR