Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU) › from 2016.03
RM3250E _57 Power Source / Network _038063 NETWORKING _0262517 CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)  Skid Control ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Skid Control ECU Communication Stop Mode Either condition is met:
·

Communication stop for "Skid Control (ABS/VSC/TRAC)" is indicated on the "Communication Bus Check" screen of the GTS.

(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Skid Control ECU Communication Stop Mode" in "DTC Combination Table".

(Click here)


·

Power source circuit of brake actuator assembly (skid control ECU)

·

Brake actuator assembly (skid control ECU) ground circuit

·

Brake actuator assembly (skid control ECU) CAN branch wire or connector

·

Brake actuator assembly (skid control ECU)



WIRING DIAGRAM

C348058E01
0.094,1.385 2.135,1.635 2.042,0.25 10 false No. 1 CAN Junction Connector 0.083,1.229 2.125,1.479 2.042,0.25 10 false G67 1.604,0.417 2.135,0.719 0.531,0.302 10 false 1 1.604,0.813 2.135,1.115 0.531,0.302 10 false 11 5.615,0.563 6.167,0.802 0.552,0.24 10 false CANH 5.615,0.979 6.167,1.219 0.552,0.24 10 false CANL 5.604,1.667 6.156,1.906 0.552,0.24 10 false +BS 5.646,2.146 6.198,2.385 0.552,0.24 10 false BM 5.625,2.635 6.177,2.875 0.552,0.24 10 false IG1 5.635,4.01 6.188,4.25 0.552,0.24 10 false GND1 5.625,4.5 6.177,4.74 0.552,0.24 10 false GND2 5.177,5.042 6.781,5.552 1.604,0.51 10 false Brake Actuator Assembly (Skid Control ECU) 5.281,0.417 5.813,0.719 0.531,0.302 10 false 22 5.281,0.833 5.813,1.135 0.531,0.302 10 false 10 5.26,1.51 5.792,1.813 0.531,0.302 10 false 38 5.271,1.979 5.802,2.281 0.531,0.302 10 false 13 5.271,2.469 5.802,2.771 0.531,0.302 10 false 12 5.292,3.854 5.823,4.156 0.531,0.302 10 false 25 5.344,4.344 5.875,4.646 0.531,0.302 10 false 1 3.927,1.49 5.156,1.688 1.229,0.198 10 false ABS NO.2 3.938,1.938 5.167,2.135 1.229,0.198 10 false ABS NO.1 3.938,2.427 5.167,2.625 1.229,0.198 10 false IG1 NO.3 2.031,1.646 3.26,1.844 1.229,0.198 10 false from Battery 2.042,2.104 3.271,2.302 1.229,0.198 10 false from Battery 0.313,2.646 3.135,2.917 2.823,0.271 10 false from IG1 NO.1 Relay*1, Ignition Switch*2 0.719,3.333 3.542,3.604 2.823,0.271 10 false from Engine Stop and Start ECU*4 3.281,2.469 3.594,2.667 0.313,0.198 10 false *3 0.167,3.917 2.99,4.188 2.823,0.271 10 false *1: w/ Entry and Start System 0.177,4.333 3,4.604 2.823,0.271 10 false *2: w/o Entry and Start System 0.177,4.75 3,5.021 2.823,0.271 10 false *3: w/o Stop and Start System 0.177,5.167 3,5.438 2.823,0.271 10 false *4: w/ Stop and Start System 3.281,3.156 3.594,3.354 0.313,0.198 10 false *4 5.177,4.865 6.771,5.083 1.594,0.219 10 false A4

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

DTC check procedure: Drive the vehicle at a speed of 5 km/h (3 mph) or more for 7 seconds or more.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (SKID CONTROL ECU CAN BRANCH WIRE)
a.
C348059C01
1.427,0.542 1.938,0.885 0.51,0.344 2.094,1.531 2.292,0.885 2.292,0.885 2.417,0.885 true 2.104,1.719 2.281,2.688 2.281,2.688 2.406,2.688 true 0.083,0.104 0.396,0.26 0.313,0.156 10 false *a 1.625,0.625 1.938,0.823 0.313,0.198 10 false A4 2.479,2.604 3.094,2.802 0.615,0.198 10 false CANH 2.479,0.802 3.094,1 0.615,0.198 10 false CANL
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the brake actuator assembly (skid control ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A4-22 (CANH) - A4-10 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result Proceed to
OK (w/o Stop and Start System) A
OK (w/ Stop and Start System) B
NG C



A

2.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BATTERY AND BODY GROUND)

B

3.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BATTERY AND BODY GROUND)

C

REPAIR OR REPLACE SKID CONTROL ECU CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

2.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BATTERY AND BODY GROUND)
a.
C348059C02
1.427,0.542 1.938,0.885 0.51,0.344 2.573,1.542 2.813,1.021 2.813,1.021 2.938,1.021 true 2.583,1.854 2.792,2.604 2.792,2.604 2.917,2.604 true 2.354,1.542 2.688,0.698 2.688,0.698 2.813,0.698 true 0.854,1.51 0.688,0.844 0.688,0.844 0.521,0.844 true 0.854,1.854 0.698,2.583 0.698,2.583 0.531,2.583 true 0.083,0.104 0.396,0.26 0.313,0.156 10 false *a 1.625,0.625 1.938,0.823 0.313,0.198 10 false A4 3,2.51 3.365,2.771 0.365,0.26 10 false +BS 0.094,2.51 0.563,2.698 0.469,0.188 10 false GND1 2.99,0.938 3.323,1.177 0.333,0.24 10 false BM 2.875,0.615 3.188,0.813 0.313,0.198 10 false IG1 0.063,0.781 0.542,0.979 0.479,0.198 10 false GND2
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])


Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A4-38 (+BS) - Body ground Always 11 to 14 V
A4-13 (BM) - Body ground Always 11 to 14 V
A4-12 (IG1) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A4-25 (GND1) - Body ground Always Below 1 Ω
A4-1 (GND2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BATTERY AND BODY GROUND)
a.
C348059C02
1.427,0.542 1.938,0.885 0.51,0.344 2.573,1.542 2.813,1.021 2.813,1.021 2.938,1.021 true 2.583,1.854 2.792,2.604 2.792,2.604 2.917,2.604 true 2.354,1.542 2.688,0.698 2.688,0.698 2.813,0.698 true 0.854,1.51 0.688,0.844 0.688,0.844 0.521,0.844 true 0.854,1.854 0.698,2.583 0.698,2.583 0.531,2.583 true 0.083,0.104 0.396,0.26 0.313,0.156 10 false *a 1.625,0.625 1.938,0.823 0.313,0.198 10 false A4 3,2.51 3.365,2.771 0.365,0.26 10 false +BS 0.094,2.51 0.563,2.698 0.469,0.188 10 false GND1 2.99,0.938 3.323,1.177 0.333,0.24 10 false BM 2.875,0.615 3.188,0.813 0.313,0.198 10 false IG1 0.063,0.781 0.542,0.979 0.479,0.198 10 false GND2
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])


Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A4-38 (+BS) - Body ground Always 11 to 14 V
A4-13 (BM) - Body ground Always 11 to 14 V
A4-12 (IG1) - Body ground Ignition switch ON 10.5 to 16 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A4-25 (GND1) - Body ground Always Below 1 Ω
A4-1 (GND2) - Body ground Always Below 1 Ω



Result:
Result Proceed to
OK A
NG (IG1 terminal) B
NG (except IG1 terminal) C



A

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR