Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU) › from 2016.03
RM3250E _57 Power Source / Network _038063 NETWORKING _0262517 CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)  Combination Meter ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Combination Meter ECU Communication Stop Mode Either condition is met:
·

Communication stop for "Combination Meter" is indicated on the "Communication Bus Check" screen of the GTS.

(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Combination Meter ECU Communication Stop Mode" in "DTC Combination Table".

(Click here)


·

Power source circuit of combination meter assembly

·

Combination meter assembly ground circuit

·

Combination meter assembly CAN main wire or connector

·

Combination meter assembly



WIRING DIAGRAM

C329331E05
1.531,0.865 2.146,1.24 0.615,0.375 10 false 5 1.521,1.396 2.135,1.771 0.615,0.375 10 false 15 0.177,1.875 0.792,2.25 0.615,0.375 10 false G67 0.177,2.042 2.229,2.354 2.052,0.313 10 false No. 1 CAN Junction Connector 2.26,2.354 3.188,2.625 0.927,0.271 10 false from Battery 0.896,3.135 3.292,3.5 2.396,0.365 10 false from IG2 Relay*1, Ignition Switch*2 0.938,3.646 3.104,4.01 2.167,0.365 10 false from Engine Stop and Start ECU*4 3.958,2.219 4.948,2.458 0.99,0.24 10 false ECU-B NO.1 4.115,2.979 4.729,3.354 0.615,0.375 10 false METER 5.333,2.24 5.948,2.615 0.615,0.375 10 false 21 5.344,3 5.958,3.375 0.615,0.375 10 false 22 5.656,2.344 6.271,2.719 0.615,0.375 10 false B 5.656,3.104 6.271,3.479 0.615,0.375 10 false IG+ 5.365,4.24 5.979,4.615 0.615,0.375 10 false 27 5.646,4.375 6.26,4.75 0.615,0.375 10 false EP 5.177,4.781 5.792,5.156 0.615,0.375 10 false G9 5.167,4.948 7.021,5.26 1.854,0.313 10 false Combination Meter Assembly 5.354,0.844 5.969,1.219 0.615,0.375 10 false 36 5.646,0.854 6.26,1.229 0.615,0.375 10 false CANH 5.354,1.396 5.969,1.771 0.615,0.375 10 false 35 5.656,1.667 6.271,2.042 0.615,0.375 10 false CANL 3.479,3.26 4.094,3.635 0.615,0.375 10 false *3 3.49,3.802 4.104,4.177 0.615,0.375 10 false *4 0.125,4.281 2.406,4.615 2.281,0.333 10 false *1: w/ Entry and Start System 0.135,4.677 2.156,5.042 2.021,0.365 10 false *2: w/o Entry and Start System 0.146,5.01 2.167,5.375 2.021,0.365 10 false *3: w/o Stop and Start System 0.146,5.375 2.167,5.74 2.021,0.365 10 false *4: w/ Stop and Start System

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

DTC check procedure: Drive the vehicle at a speed of 5 km/h (3 mph) or more for 52 seconds or more.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)>DIAGNOSIS SYSTEM

·

When replacing the combination meter assembly, make sure to replace it with a new one.



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (COMBINATION METER ASSEMBLY CAN MAIN WIRE)
a.
C221258C12
1.521,0.333 1.927,0.615 0.406,0.281 1.125,1.979 1.292,1.979 1.292,1.979 1.385,1.354 true 0.917,1.76 1.063,1.76 1.063,1.76 1.313,1.333 true 0.073,0.052 0.24,0.24 0.167,0.188 10 false *a 0.49,1.688 0.917,1.844 0.427,0.156 10 false CANH 0.708,1.906 1.104,2.063 0.396,0.156 10 false CANL 1.625,0.385 1.948,0.573 0.323,0.188 10 false G9
*a Rear view of wire harness connector
(to Combination Meter Assembly)


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G9-36 (CANH) - G9-35 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result Proceed to
OK (w/o Stop and Start System) A
OK (w/ Stop and Start System) B
NG C



A

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BATTERY AND BODY GROUND)

B

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BATTERY AND BODY GROUND)

C

REPAIR OR REPLACE COMBINATION METER ASSEMBLY CAN MAIN WIRE OR CONNECTOR (CANH, CANL)

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BATTERY AND BODY GROUND)
a.
C240157C54
1.531,0.146 1.969,0.458 0.438,0.313 2.865,1.448 2.708,1.448 2.708,1.448 2.563,1.229 true 2.635,0.552 2.479,0.552 2.479,0.552 2.052,1.198 true 2.854,1.792 2.698,1.792 2.698,1.792 2.458,1.24 true 0.073,0.083 0.385,0.24 0.313,0.156 10 false *a 1.635,0.229 2.094,0.427 0.458,0.198 10 false G9 2.917,1.385 3.219,1.656 0.302,0.271 10 false B 2.698,0.469 3.063,0.729 0.365,0.26 10 false EP 2.906,1.729 3.208,2 0.302,0.271 10 false IG+
*a Rear view of wire harness connector
(to Combination Meter Assembly)


Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G9-21 (B) - Body ground Always 11 to 14 V
G9-22 (IG+) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G9-27 (EP) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BATTERY AND BODY GROUND)
a.
C240157C54
1.531,0.146 1.969,0.458 0.438,0.313 2.865,1.448 2.708,1.448 2.708,1.448 2.563,1.229 true 2.635,0.552 2.479,0.552 2.479,0.552 2.052,1.198 true 2.854,1.792 2.698,1.792 2.698,1.792 2.458,1.24 true 0.073,0.083 0.385,0.24 0.313,0.156 10 false *a 1.635,0.229 2.094,0.427 0.458,0.198 10 false G9 2.917,1.385 3.219,1.656 0.302,0.271 10 false B 2.698,0.469 3.063,0.729 0.365,0.26 10 false EP 2.906,1.729 3.208,2 0.302,0.271 10 false IG+
*a Rear view of wire harness connector
(to Combination Meter Assembly)


Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G9-21 (B) - Body ground Always 11 to 14 V
G9-22 (IG+) - Body ground Ignition switch ON 10.5 to 16 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G9-27 (EP) - Body ground Always Below 1 Ω



Result:
Result Proceed to
OK A
NG (IG+ terminal) B
NG (except IG+ terminal) C



A

REPLACE COMBINATION METER ASSEMBLY

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR