Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU) › from 2016.03
RM3250E _57 Power Source / Network _038063 NETWORKING _0262517 CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)  Check Bus 2 Line for Short to GND  


DESCRIPTION

There may be a short circuit between one of the CAN bus wires and GND when no resistance exists between terminal 18 (CA4H) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 17 (CA4L) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3.

Detection Item Trouble Area

*1: for Automatic Air Conditioning System or Manual Air Conditioning System

*2: w/ Entry and Start System

*3: for 4WD

*4: for LED Headlight or w/ Headlight Cleaner System

*5: w/ Stop and Start System

No resistance exists between terminal 18 (CA4H) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 17 (CA4L) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3.
·

Short to GND in bus 2 CAN main wires

·

Short to GND in bus 2 CAN branch wires

·

ECM

·

Combination meter assembly

·

Central gateway ECU (network gateway ECU)

·

Brake actuator assembly (skid control ECU)

·

Spiral with sensor cable sub-assembly (steering angle sensor)

·

Air conditioning amplifier assembly*1

·

Airbag sensor assembly

·

Certification ECU (smart key ECU assembly)*2

·

4 wheel drive control ECU*3

·

Headlight leveling ECU assembly*4

·

Engine stop and start ECU*5

·

No. 1 CAN junction connector

·

No. 2 CAN junction connector



WIRING DIAGRAM

C355942E01
0.906,0.375 1.521,0.573 0.615,0.198 10 false CANH 6.021,0.281 6.635,0.479 0.615,0.198 10 false CANH 6.01,2.427 6.625,2.625 0.615,0.198 10 false CANH 6.021,6.042 6.635,6.24 0.615,0.198 10 false CANH 1.063,6.042 1.677,6.24 0.615,0.198 10 false CANH 0.917,0.906 1.531,1.104 0.615,0.198 10 false CANL 6.042,1.052 6.656,1.25 0.615,0.198 10 false CANL 6.021,2.969 6.635,3.167 0.615,0.198 10 false CANL 1.073,6.573 1.688,6.771 0.615,0.198 10 false CANL 6.031,6.573 6.646,6.771 0.615,0.198 10 false CANL 0.063,1.333 0.521,1.531 0.458,0.198 10 false G70 0.063,1.49 1.719,1.833 1.656,0.344 10 false Certification ECU (Smart Key ECU Assembly)*1 6.271,1.354 6.729,1.552 0.458,0.198 10 false G85 6.25,1.51 6.708,1.708 0.458,0.198 10 false ECM 5.917,3.365 6.375,3.563 0.458,0.198 10 false C39 5.927,3.531 6.927,3.917 1,0.385 10 false 4 Wheel Drive Control ECU*2 2.302,4.448 2.76,4.646 0.458,0.198 10 false G68 2.313,4.625 4.292,4.813 1.979,0.188 10 false No. 2 CAN Junction Connector 2.677,0.281 2.885,0.438 0.208,0.156 10 false 3 2.604,0.802 2.917,1 0.313,0.198 10 false 13 1.406,0.271 1.719,0.469 0.313,0.198 10 false 40 1.406,0.802 1.719,1 0.313,0.198 10 false 18 3.573,0.281 3.729,0.479 0.156,0.198 10 false 5 3.563,0.813 3.875,1.01 0.313,0.198 10 false 15 5.74,0.281 6.052,0.479 0.313,0.198 10 false 17 5.75,1.031 6.063,1.229 0.313,0.198 10 false 28 3.594,2.323 3.75,2.521 0.156,0.198 10 false 4 3.573,2.854 3.875,3.042 0.302,0.188 9 false 14 5.74,2.302 6.052,2.5 0.313,0.198 10 false 20 5.75,2.854 6.063,3.052 0.313,0.198 10 false 40 3.594,3.417 3.781,3.615 0.188,0.198 10 false 6 3.573,3.948 3.885,4.146 0.313,0.198 10 false 16 5.531,6.938 5.844,7.135 0.313,0.198 10 false A4 5.385,7.073 7.156,7.49 1.771,0.417 10 false Brake Actuator Assemblybly (Skid Control ECU) 0.25,6.927 0.708,7.125 0.458,0.198 10 false G42 0.25,7.094 1.917,7.292 1.667,0.198 10 false Airbag Sensor Assembly 3.573,5.25 3.729,5.448 0.156,0.198 10 false 6 3.552,5.552 3.865,5.75 0.313,0.198 10 false 16 3.583,5.938 3.74,6.135 0.156,0.198 10 false 1 3.583,6.479 3.896,6.677 0.313,0.198 10 false 11 1.542,5.948 1.854,6.146 0.313,0.198 10 false 13 1.552,6.479 1.865,6.677 0.313,0.198 10 false 22 2.25,7.49 2.708,7.688 0.458,0.198 10 false G67 2.26,7.667 4.25,7.854 1.99,0.188 10 false No. 1 CAN Junction Connector 0.156,8.135 2.146,8.323 1.99,0.188 10 false *1: w/ Entry and Start System 0.167,8.521 1.854,8.719 1.688,0.198 10 false *2: for 4WD 5.75,5.938 6.063,6.135 0.313,0.198 10 false 22 5.75,6.469 6.063,6.667 0.313,0.198 10 false 10 2.677,5.958 2.823,6.167 0.146,0.208 10 false 2 2.615,6.479 2.927,6.677 0.313,0.198 10 false 12

C355943E01
0.156,2.344 0.771,2.542 0.615,0.198 10 false G127 0.156,2.5 2.094,2.74 1.938,0.24 10 false Engine Stop and Start ECU*1 0.927,3.438 1.542,3.635 0.615,0.198 10 false CA4H 0.906,1.438 1.521,1.635 0.615,0.198 10 false CANH 5.99,1.438 6.604,1.635 0.615,0.198 10 false CANH 6.031,5.323 6.646,5.521 0.615,0.198 10 false CANH 6.01,3.448 6.625,3.646 0.615,0.198 10 false CANH 0.927,1.969 1.542,2.167 0.615,0.198 10 false CANL 6,1.958 6.615,2.156 0.615,0.198 10 false CANL 6.052,6.052 6.667,6.25 0.615,0.198 10 false CANL 0.938,3.979 1.552,4.177 0.615,0.198 10 false CA4L 6.021,3.979 6.635,4.177 0.615,0.198 10 false CANL 1.406,1.323 1.719,1.521 0.313,0.198 10 false 13 1.406,1.844 1.719,2.042 0.313,0.198 10 false 14 3.198,1.323 3.354,1.521 0.156,0.198 10 false 7 3.167,1.854 3.479,2.052 0.313,0.198 10 false 17 4.146,1.323 4.302,1.521 0.156,0.198 10 false 3 4.125,1.854 4.438,2.052 0.313,0.198 10 false 13 5.792,1.333 5.948,1.531 0.156,0.198 10 false 3 5.792,1.865 5.948,2.063 0.156,0.198 10 false 2 4.76,2.323 5.219,2.521 0.458,0.198 10 false G21 4.76,2.479 7.156,2.896 2.396,0.417 10 false Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor) 1.406,3.333 1.719,3.531 0.313,0.198 10 false 18 1.417,3.875 1.729,4.073 0.313,0.198 10 false 17 0.115,4.344 0.729,4.542 0.615,0.198 10 false G128 0.115,4.479 1.688,4.875 1.573,0.396 10 false Central Gateway ECU (Network Gateway ECU) 4.854,4.25 5.313,4.448 0.458,0.198 10 false G80 4.865,4.417 7.156,4.698 2.292,0.281 10 false Headlight Leveling ECU Assembly*2 3.208,3.344 3.365,3.542 0.156,0.198 10 false 9 3.167,3.875 3.479,4.073 0.313,0.198 10 false 19 4.167,3.344 4.323,3.542 0.156,0.198 10 false 8 4.146,3.875 4.458,4.073 0.313,0.198 10 false 18 5.792,3.354 5.948,3.552 0.156,0.198 10 false 6 5.802,3.875 5.958,4.073 0.156,0.198 10 false 7 2.958,6.302 3.417,6.5 0.458,0.198 10 false G67 2.969,6.458 4.906,6.708 1.938,0.25 10 false No. 1 CAN Junction Connector 4.146,5.313 4.302,5.51 0.156,0.198 10 false 5 4.125,5.844 4.438,6.042 0.313,0.198 10 false 15 5.729,5.302 6.042,5.5 0.313,0.198 10 false 36 5.74,5.844 6.052,6.042 0.313,0.198 10 false 35 5.281,6.302 5.594,6.5 0.313,0.198 10 false G9 5.281,6.458 7.156,6.76 1.875,0.302 10 false Combination Meter Assembly 0.115,6.344 2.406,6.656 2.292,0.313 10 false Air Conditioning Amplifier Assembly 1.073,5.396 1.406,5.594 0.333,0.198 10 false TX+ 1.073,5.927 1.396,6.125 0.323,0.198 10 false TX- 1.427,5.406 1.885,5.604 0.458,0.198 10 false G33 1.438,5.938 1.896,6.135 0.458,0.198 10 false G33 1.865,5.406 2.323,5.604 0.458,0.198 10 false G77 1.865,5.948 2.323,6.146 0.458,0.198 10 false G77 1.427,5.208 1.74,5.406 0.313,0.198 10 false 11*3 1.896,5.208 2.135,5.427 0.24,0.219 10 false 8*4 1.427,5.729 1.75,5.969 0.323,0.24 10 false 12*3 1.896,5.74 2.188,5.917 0.292,0.177 10 false 9*4 3.146,5.302 3.458,5.5 0.313,0.198 10 false 10 3.167,5.844 3.479,6.042 0.313,0.198 10 false 20 0.198,7.698 2.063,7.979 1.865,0.281 10 false *1: w/ Stop and Start System 0.208,8.125 3.521,8.396 3.313,0.271 10 false *2: for LED Headlight or w/ Headlight Cleaner System 3.625,7.708 6.354,8.031 2.729,0.323 10 false *3: for Automatic Air Conditioning System 3.635,8.135 6.063,8.396 2.427,0.26 10 false *4: for Manual Air Conditioning System

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.

C348063C08
1.813,0.563 2.333,0.865 0.521,0.302 5.24,0.417 5.76,0.719 0.521,0.302 1.479,1.417 1.021,0.823 1.021,0.823 0.854,0.823 true 1.656,1.406 1.146,0.594 1.146,0.594 0.979,0.594 true 1.479,1.563 1.042,2.073 1.042,2.073 0.875,2.073 true 1.677,1.573 1.167,2.354 1.167,2.354 1,2.354 true 2.229,1.385 2.875,0.646 2.875,0.646 3.031,0.646 true 2.208,1.552 2.875,2.229 2.875,2.229 3.031,2.229 true 1.885,1.583 1.313,2.583 1.313,2.583 1.146,2.583 true 1.844,1.385 1.281,0.313 1.281,0.313 1.115,0.313 true 5.385,1.208 4.938,0.76 4.938,0.76 4.771,0.76 true 1.938,0.625 2.552,0.823 0.615,0.198 10 false G68 5.406,0.49 6.021,0.688 0.615,0.198 10 false G8 0.302,0.74 1.219,0.938 0.917,0.198 10 false CANH*c 0.417,0.5 1.333,0.698 0.917,0.198 10 false CANH*d 3.083,0.573 4,0.771 0.917,0.198 10 false CANH*f 0.542,0.208 1.458,0.406 0.917,0.198 10 false CANH*e 0.323,1.99 1.24,2.188 0.917,0.198 10 false CANL*c 0.458,2.26 1.375,2.458 0.917,0.198 10 false CANL*d 0.635,2.49 1.552,2.688 0.917,0.198 10 false CANL*e 3.115,2.156 4.031,2.354 0.917,0.198 10 false CANL*f 0.135,0.104 1.052,0.302 0.917,0.198 10 false *a 4.146,0.135 5.063,0.333 0.917,0.198 10 false *b 4.51,0.688 4.917,1.083 0.406,0.396 10 false CG
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b Front view of DLC3
*c to Certification ECU (Smart Key ECU Assembly) (w/ Entry and Start System) *d to 4 Wheel Drive Control ECU (for 4WD)
*e to ECM *f to No. 1 CAN Junction Connector



b.

Disconnect the No. 2 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to

*1: w/ Entry and Start System

*2: for 4WD

G68-3 (CANH) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Certification ECU (smart key ECU assembly)*1
G68-13 (CANL) - G8-4 (CG)
G68-4 (CANH) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher 4 wheel drive control ECU*2
G68-14 (CANL) - G8-4 (CG)
G68-5 (CANH) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher ECM
G68-15 (CANL) - G8-4 (CG)
G68-6 (CANH) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher No. 1 CAN junction connector
G68-16 (CANL) - G8-4 (CG)



Result:
Result Proceed to
OK A
NG (No. 1 CAN junction connector CAN main wire) B
NG (ECU or sensor CAN main or branch wires) C



A

REPLACE NO. 2 CAN JUNCTION CONNECTOR

B

2.CONNECT CONNECTOR

C

6.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECU, SENSOR)
2.CONNECT CONNECTOR
a.

Reconnect the G68 No. 2 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

3.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR)
3.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 1 CAN junction connector.

C348063C10
1.813,0.563 2.333,0.865 0.521,0.302 5.24,0.417 5.76,0.719 0.521,0.302 1.083,1.417 0.854,1.01 0.854,1.01 0.688,1.01 true 1.281,1.427 0.99,0.802 0.99,0.802 0.823,0.802 true 1.094,1.583 0.885,1.906 0.885,1.906 0.719,1.906 true 1.292,1.573 0.969,2.104 0.969,2.104 0.802,2.104 true 2.229,1.406 2.896,0.375 2.896,0.375 3.052,0.375 true 2.198,1.563 2.906,2.552 2.906,2.552 3.063,2.552 true 1.5,1.563 1.115,2.313 1.115,2.313 0.948,2.313 true 1.479,1.417 1.115,0.615 1.115,0.615 0.948,0.615 true 1.844,1.417 1.208,0.427 1.208,0.427 1.042,0.427 true 1.854,1.573 1.229,2.521 1.229,2.521 1.063,2.521 true 2.406,1.563 3,2.365 3,2.365 3.156,2.365 true 2.438,1.417 3,0.573 3,0.573 3.156,0.573 true 2.625,1.427 3.094,0.792 3.094,0.792 3.25,0.792 true 2.625,1.583 3.115,2.208 3.115,2.208 3.271,2.208 true 2.813,1.427 3.188,0.979 3.188,0.979 3.344,0.979 true 2.781,1.563 3.156,2.031 3.156,2.031 3.313,2.031 true 5.344,1.198 4.813,0.76 4.813,0.76 4.646,0.76 true 3,1.417 3.25,1.167 3.25,1.167 3.417,1.167 false 3,1.583 3.25,1.833 3.25,1.833 3.417,1.833 false 1.938,0.625 2.552,0.823 0.615,0.198 10 false G67 5.406,0.49 6.021,0.688 0.615,0.198 10 false G8 0.167,0.938 1.083,1.135 0.917,0.198 10 false CANH*c 0.25,0.729 1.167,0.927 0.917,0.198 10 false CANH*d 3.083,0.292 4,0.49 0.917,0.198 10 false CANH*g 0.396,0.542 1.313,0.74 0.917,0.198 10 false CANH*e 0.167,1.833 1.083,2.031 0.917,0.198 10 false CANL*c 0.26,2.031 1.177,2.229 0.917,0.198 10 false CANL*d 0.375,2.24 1.292,2.438 0.917,0.198 10 false CANL*e 3.125,2.479 4.042,2.677 0.917,0.198 10 false CANL*g 0.135,0.104 1.052,0.302 0.917,0.198 10 false *a 4.146,0.135 5.063,0.333 0.917,0.198 10 false *b 4.385,0.688 4.792,1.083 0.406,0.396 10 false CG 0.5,0.333 1.417,0.531 0.917,0.198 10 false CANH*f 0.542,2.427 1.458,2.625 0.917,0.198 10 false CANL*f 3.24,2.281 4.156,2.479 0.917,0.198 10 false CANL*h 3.219,0.5 4.135,0.698 0.917,0.198 10 false CANH*h 3.313,0.708 4.229,0.906 0.917,0.198 10 false CANH*i 3.333,2.125 4.25,2.323 0.917,0.198 10 false CANL*i 3.385,0.906 4.302,1.104 0.917,0.198 10 false CANH*j 3.365,1.958 4.281,2.156 0.917,0.198 10 false CANL*j 3.458,1.094 4.375,1.292 0.917,0.198 10 false CANH*k 3.469,1.75 4.385,1.948 0.917,0.198 10 false CANL*k
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b Front view of DLC3
*c to Brake Actuator Assembly (Skid Control ECU) *d to Airbag Sensor Assembly
*e to Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor) *f to Combination Meter Assembly
*g to No. 2 CAN Junction Connector *h to Engine Stop and Start ECU (w/ Stop and Start System)
*i to Headlight Leveling ECU Assembly (for LED Headlight or w/ Headlight Cleaner System) *j to Central Gateway ECU (Network Gateway ECU)
*k
·

to Air Conditioning Amplifier Assembly (for Automatic Air Conditioning System)

·

to Air Conditioning AmplifierAssembly (for Manual AirConditioning System)


- -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to

*1: w/ Stop and Start System

*2: for LED Headlight or w/ Headlight Cleaner System

*3: for Automatic Air Conditioning System

*4: for Manual Air Conditioning System

G67-1 (CANH) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Brake actuator assembly (skid control ECU)
G67-11 (CANL) - G8-4 (CG)
G67-2 (CANH) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Airbag sensor assembly
G67-12 (CANL) - G8-4 (CG)
G67-3 (CANH) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Spiral with sensor cable sub-assembly (steering angle sensor)
G67-13 (CANL) - G8-4 (CG)
G67-5 (CANH) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Combination meter assembly
G67-15 (CANL) - G8-4 (CG)
G67-6 (CANH) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher No. 2 CAN junction connector
G67-16 (CANL) - G8-4 (CG)
G67-7 (CANH) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Engine stop and start ECU*1
G67-17 (CANL) - G8-4 (CG)
G67-8 (CANH) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Headlight leveling ECU assembly*2
G67-18 (CANL) - G8-4 (CG)
G67-9 (CANH) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Central gateway ECU (network gateway ECU)
G67-19 (CANL) - G8-4 (CG)
G67-10(CANH) -G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Airconditioningamplifierassembly*3,*4
G67-20(CANL) -G8-4 (CG)



Result:
Result Proceed to
OK A
NG (No. 2 CAN junction connector CAN main wire) B
NG (Central gateway ECU [network gateway ECU] CAN branch wire) C
NG (ECU or sensor CAN main or branch wires) D



A

REPLACE NO. 1 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)

C

4.CONNECT CONNECTOR

D

6.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECU, SENSOR)
4.CONNECT CONNECTOR
a.

Reconnect the G67 No. 1 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

5.CHECK FOR SHORT TO GND IN CAN BUS WIRE (CENTRAL GATEWAY ECU)
5.CHECK FOR SHORT TO GND IN CAN BUS WIRE (CENTRAL GATEWAY ECU)
a.
C348065C05
1.5,0.313 1.958,0.667 0.458,0.354 1.51,2.438 1.969,2.792 0.458,0.354 1.052,2.188 1.188,2.188 1.188,2.188 1.635,1.521 true 1.229,2.396 1.365,2.396 1.365,2.396 1.771,1.51 true 0.854,2.771 0.99,2.771 0.99,2.771 1.583,3.167 true 0.073,0.042 0.385,0.198 0.313,0.156 10 false *a 0.063,2.49 0.375,2.646 0.313,0.156 10 false *b 1.563,0.406 2.177,0.604 0.615,0.198 10 false G128 1.656,2.552 2.271,2.75 0.615,0.198 10 false G8 0.573,2.698 1.188,2.896 0.615,0.198 10 false CG 0.802,2.333 1.417,2.531 0.615,0.198 10 false CA4H 0.698,2.104 1.313,2.302 0.615,0.198 10 false CA4L
*a Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU])
*b Front view of DLC3


Disconnect the central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G128-18 (CA4H) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G128-17 (CA4L) - G8-4 (CG)



Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CENTRAL GATEWAY ECU - NO. 1 CAN JUNCTION CONNECTOR)

6.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECU, SENSOR)
a.
C348064C15
1.438,0.219 1.927,0.552 0.49,0.333 1.427,2.406 1.917,2.74 0.49,0.333 2.198,1.771 2.063,1.771 2.063,1.771 1.771,1.156 true 2.156,2.01 2.021,2.01 2.021,2.01 1.688,1.156 true 1,2.708 1.146,2.708 1.146,2.708 1.594,3.094 true 0.104,0.083 0.417,0.24 0.313,0.156 10 false *a 0.115,2.604 0.427,2.76 0.313,0.156 10 false *b 1.521,0.313 2.135,0.51 0.615,0.198 10 false G128 1.594,2.5 2.208,2.698 0.615,0.198 10 false G8 2.25,1.688 2.865,1.885 0.615,0.198 10 false CA4L 2.208,1.938 2.823,2.135 0.615,0.198 10 false CA4H 0.729,2.635 1.344,2.833 0.615,0.198 10 false CG
*a Component with harness connected
(Central Gateway ECU [Network Gateway ECU])
*b Front view of DLC3


Reconnect the CAN junction connector.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to GND is connected.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G128-18 (CA4H) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G128-17 (CA4L) - G8-4 (CG)


HINT:

If the resistance changes to 200 Ω or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.



Result:
Proceed to
OK
NG



OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR CAN BUS WIRES OR CONNECTOR