Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU) › from 2016.03
RM3250E _57 Power Source / Network _038063 NETWORKING _0262517 CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)  Check Bus 3 Line for Short to GND  


DESCRIPTION

There may be a short circuit between one of the CAN bus wires and GND when no resistance exists between terminal 6 (CA3H) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 21 (CA3L) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3.

Detection Item Trouble Area

*1: w/ Audio and Visual System (for Radio and Display Type)

*2: w/ Navigation System

No resistance exists between terminal 6 (CA3H) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 21 (CA3L) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3.
·

Short to GND in bus 3 CAN main wires

·

Short to GND in bus 3 CAN branch wires

·

Central gateway ECU (network gateway ECU)

·

Radio and display receiver assembly*1

·

Navigation receiver assembly*2

·

No. 4 CAN junction connector



WIRING DIAGRAM

C348067E01
2.792,5.698 4.885,6.094 2.094,0.396 10 false No. 4 CAN Junction Connector 5.188,5.698 7.156,6.094 1.969,0.396 10 false Central Gateway ECU (Network Gateway ECU) 5.177,5.531 5.792,5.729 0.615,0.198 10 false G128 6.094,0.688 6.708,0.885 0.615,0.198 10 false CA3H 6.125,1.438 6.74,1.635 0.615,0.198 10 false CA3L 6.083,4.375 6.698,4.573 0.615,0.198 10 false CAYH 6.115,5.146 6.729,5.344 0.615,0.198 10 false CAYL 5.771,1.156 6.083,1.354 0.313,0.198 10 false 21 5.833,0.677 6.146,0.875 0.313,0.198 10 false 6 5.75,4.385 6.063,4.583 0.313,0.198 10 false 19 5.75,4.833 6.063,5.031 0.313,0.198 10 false 20 4.594,0.552 4.906,0.75 0.313,0.198 10 false 1 4.594,1.042 4.906,1.24 0.313,0.198 10 false 2 2.969,1.917 3.281,2.115 0.313,0.198 10 false 2 2.979,1.365 3.292,1.563 0.313,0.198 10 false 1 4.604,4.24 4.917,4.438 0.313,0.198 10 false 1 4.604,4.76 4.917,4.958 0.313,0.198 10 false 2 4.479,4.521 5.094,4.719 0.615,0.198 10 false G133 4.479,4.99 5.094,5.188 0.615,0.198 10 false G133 4.479,0.823 5.094,1.021 0.615,0.198 10 false G135 4.479,1.292 5.094,1.49 0.615,0.198 10 false G135 2.833,1.635 3.448,1.833 0.615,0.198 10 false G132 2.844,2.156 3.458,2.354 0.615,0.198 10 false G132 0.094,2.625 2.615,3.177 2.521,0.552 10 false Radio and Display Receiver Assembly*1, Navigation Receiver Assembly*2 1.708,1.635 2.323,1.833 0.615,0.198 10 false G37 1.719,2.167 2.333,2.365 0.615,0.198 10 false G37 2.135,1.635 2.75,1.833 0.615,0.198 10 false G113 2.135,2.167 2.75,2.365 0.615,0.198 10 false G113 1.719,1.396 2.333,1.594 0.615,0.198 10 false 9*1 2.198,1.396 2.813,1.594 0.615,0.198 10 false 9*2 1.708,1.938 2.323,2.135 0.615,0.198 10 false 10*1 2.167,1.938 2.781,2.135 0.615,0.198 10 false 10*2 0.146,4.448 2.135,4.833 1.99,0.385 10 false *1: w/ Audio and Visual System (for Radio and Display Type) 0.156,5.24 2.146,5.625 1.99,0.385 10 false *2: w/ Navigation System 1.135,1.635 1.75,1.833 0.615,0.198 10 false CANH 1.146,2.156 1.76,2.354 0.615,0.198 10 false CANL

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.

C348068C02
3.771,0.281 4.26,0.573 0.49,0.292 1.594,3.833 2.083,4.125 0.49,0.292 4.375,0.281 4.865,0.573 0.49,0.292 4.99,0.281 5.479,0.573 0.49,0.292 5.135,3.24 5.427,2.823 5.427,2.823 5.552,2.823 true 5.104,3.417 5.458,3.833 5.458,3.833 5.583,3.833 true 1.823,4.542 1.135,4.104 1.135,4.104 0.99,4.104 true 4.052,1.25 4.052,0.583 true 4.75,1.25 4.75,0.583 true 5.167,1.25 5.167,0.583 true 2.25,1.938 2.865,2.135 0.615,0.198 10 false G135 2.25,2.49 2.865,2.688 0.615,0.198 10 false G132 2.25,2.823 2.865,3.021 0.615,0.198 10 false G133 0.104,0.104 0.719,0.302 0.615,0.198 10 false *1 4.125,2.625 4.74,2.823 0.615,0.198 10 false *a 0.125,3.833 0.74,4.031 0.615,0.198 10 false *b 1.75,3.896 2.063,4.094 0.313,0.198 10 false G8 5.615,2.74 6.24,2.979 0.625,0.24 10 false CANH 5.656,3.75 6.281,3.99 0.625,0.24 10 false CANL 0.719,4.031 1.344,4.271 0.625,0.24 10 false CG 3.844,0.344 4.458,0.542 0.615,0.198 10 false G135 4.448,0.344 5.063,0.542 0.615,0.198 10 false G132 5.063,0.354 5.677,0.552 0.615,0.198 10 false G133
*1 No. 4 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 4 CAN Junction Connector)
*b Front view of DLC3



b.

Disconnect the No. 4 CAN junction connectors.


c.

Measure the resistance according to the value(s) in the table below.

Wiring Color
Code Color (CANH Side) Color (CANL Side) Connect to

*1: w/ Audio and Visual System (for Radio and Display Type)

*2: w/ Navigation System

G132 V W
·

Radio and Display Receiver Assembly*1

·

Navigation Receiver Assembly*2


G133 V W Central Gateway ECU (Network Gateway ECU)
G135 P W

Standard Resistance:
Tester Connection Condition Specified Condition Connect to

*1: w/ Audio and Visual System (for Radio and Display Type)

*2: w/ Navigation System

G132-1 (CANH) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
·

Radio and display receiver assembly*1

·

Navigation receiver assembly*2


G132-2 (CANL) - G8-4 (CG)
G133-1 (CANH) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Central gateway ECU (network gateway ECU)
G133-2 (CANL) - G8-4 (CG)
G135-1 (CANH) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G135-2 (CANL) - G8-4 (CG)



Result:
Proceed to
OK A
NG (Central gateway ECU [network gateway ECU] CAN main wire) B
NG (ECU or sensor CAN branch wires) C



A

REPLACE NO. 4 CAN JUNCTION CONNECTOR

B

2.CONNECT CONNECTOR

C

4.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECU, SENSOR)
2.CONNECT CONNECTOR
a.

Reconnect the No. 4 CAN junction connectors.


Result:
Proceed to
NEXT



NEXT

3.CHECK FOR SHORT TO GND IN CAN BUS WIRE (CENTRAL GATEWAY ECU)
3.CHECK FOR SHORT TO GND IN CAN BUS WIRE (CENTRAL GATEWAY ECU)
a.
C348065C03
1.5,0.313 1.958,0.667 0.458,0.354 1.51,2.438 1.969,2.792 0.458,0.354 2.292,1.24 2.646,0.542 2.646,0.542 2.781,0.542 true 1.01,2.188 1.146,2.188 1.146,2.188 1.917,1.521 true 1.229,2.406 1.365,2.406 1.365,2.406 2.042,1.51 true 2.188,1.521 2.313,2.146 2.313,2.146 2.448,2.146 true 0.813,2.74 0.948,2.74 0.948,2.74 1.615,3.167 true 0.073,0.042 0.385,0.198 0.313,0.156 10 false *a 0.063,2.49 0.375,2.646 0.313,0.156 10 false *b 1.563,0.406 2.177,0.604 0.615,0.198 10 false G128 1.656,2.552 2.271,2.75 0.615,0.198 10 false G8 0.604,2.104 1.219,2.302 0.615,0.198 10 false CAYH 0.865,2.323 1.479,2.521 0.615,0.198 10 false CAYL 2.51,2.063 3.125,2.26 0.615,0.198 10 false CA3L 2.823,0.448 3.292,0.76 0.469,0.313 10 false CA3H 0.542,2.667 1.052,2.906 0.51,0.24 10 false CG
*a Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU])
*b Front view of DLC3


Disconnect the central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G128-6 (CA3H) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G128-21 (CA3L) - G8-4 (CG)
G128-19 (CAYH) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G128-20 (CAYL) - G8-4 (CG)



Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CENTRAL GATEWAY ECU - NO. 4 CAN JUNCTION CONNECTOR)

4.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECU, SENSOR)
a.
C348064C11
1.438,0.219 1.927,0.552 0.49,0.333 1.427,2.406 1.917,2.74 0.49,0.333 0.781,0.458 0.917,0.458 0.917,0.458 1.396,1 true 2.083,2.031 1.948,2.031 1.948,2.031 1.427,1.156 true 0.958,2.667 1.094,2.667 1.094,2.667 1.604,3.125 true 0.104,0.083 0.417,0.24 0.313,0.156 10 false *a 0.083,2.385 0.396,2.542 0.313,0.156 10 false *b 1.521,0.313 2.135,0.51 0.615,0.198 10 false G128 1.594,2.5 2.208,2.698 0.615,0.198 10 false G8 0.385,0.385 1,0.583 0.615,0.198 10 false CA3H 2.135,1.948 2.75,2.146 0.615,0.198 10 false CA3L 0.656,2.583 1.271,2.781 0.615,0.198 10 false CG
*a Component with harness connected
(Central Gateway ECU [Network Gateway ECU])
*b Front view of DLC3


Reconnect the CAN junction connector.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to GND is connected.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G128-6 (CA3H) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G128-21 (CA3L) - G8-4 (CG)


HINT:

If the resistance changes to 200 Ω or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.



Result:
Proceed to
OK
NG



OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR CAN BRANCH WIRES OR CONNECTOR