Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type) › from 2016.03
RM3250E _56 Audio / Visual / Telematics _038052 AUDIO / VIDEO _0182296 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Radio Receiver Power Source Circuit  


DESCRIPTION

This is the power source circuit to operate the radio and display receiver assembly.

WIRING DIAGRAM

E321740E02
1.677,0.792 2.563,1.021 0.885,0.229 10 false from Battery 0.448,0.438 2.51,0.635 2.063,0.198 10 false from Engine Stop and Start ECU 3.208,0.958 3.76,1.177 0.552,0.219 10 false RADIO 3.708,0.333 3.979,0.521 0.271,0.188 10 false *3 3.719,0.719 3.99,0.906 0.271,0.188 10 false *4 3.802,1.104 4.073,1.292 0.271,0.188 10 false *3 3.823,1.469 4.094,1.656 0.271,0.188 10 false *4 5.427,0.594 5.646,0.781 0.219,0.188 10 false 4 5.333,0.802 5.656,0.99 0.323,0.188 10 false G40 5.76,0.792 6.229,1 0.469,0.208 10 false +B1 5.427,1.354 5.646,1.542 0.219,0.188 10 false 3 5.333,1.563 5.625,1.781 0.292,0.219 10 false G40 5.771,1.573 6.271,1.781 0.5,0.208 10 false ACC1 5.427,2.208 5.646,2.396 0.219,0.188 10 false 1 5.333,2.406 5.708,2.604 0.375,0.198 10 false G37 5.781,2.406 6,2.604 0.219,0.198 10 false IG 2.094,1.719 3.177,1.969 1.083,0.25 10 false SFT LOCK-ACC 3.438,1.719 3.823,1.927 0.385,0.208 10 false ACC 0.458,1.198 2.521,1.396 2.063,0.198 10 false from Engine Stop and Start ECU 0.74,1.552 1.875,1.813 1.135,0.26 10 false from ACC Relay 5.427,2.979 5.646,3.167 0.219,0.188 10 false 7 5.344,3.198 5.719,3.365 0.375,0.167 10 false G40 5.771,3.188 6.323,3.365 0.552,0.177 10 false GND1 5.323,3.844 7.031,4.24 1.708,0.396 10 false Radio and Display Receiver Assembly 4.521,2.604 5.271,2.813 0.75,0.208 10 false IG1 NO.4 1.052,2.427 2.531,2.792 1.479,0.365 10 false from IG1 NO.1 Relay*1, Ignition Switch*2 0.26,3.177 2.615,3.469 2.354,0.292 10 false *1: w/ Entry and Start System 0.26,3.573 2.615,3.865 2.354,0.292 10 false *2: w/o Entry and Start System 0.271,3.969 2.625,4.26 2.354,0.292 10 false *3: w/ Stop and Start System 0.271,4.365 2.5,4.604 2.229,0.24 10 false *4: w/o Stop and Start System

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)
a.
E310643C04
1.49,1.854 1.927,2.083 0.438,0.229 1.49,0.333 1.927,0.563 0.438,0.229 0.552,0.979 0.708,0.979 0.708,0.979 0.958,1.219 true 1.219,3.26 1.375,3.26 1.375,3.26 1.625,2.865 true 2.25,2.531 2.469,2.365 2.469,2.365 2.625,2.365 true 2.031,2.49 2.375,2.083 2.375,2.083 2.531,2.083 true 0.156,0.135 0.469,0.292 0.313,0.156 10 false *a 1.583,0.375 2.01,0.573 0.427,0.198 10 false G37 1.573,1.896 2,2.094 0.427,0.198 10 false G40 2.583,1.969 3.01,2.167 0.427,0.198 10 false ACC1 2.677,2.26 3.104,2.458 0.427,0.198 10 false +B1 0.802,3.156 1.229,3.354 0.427,0.198 10 false GND1 0.333,0.865 0.76,1.063 0.427,0.198 10 false IG
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Disconnect the radio and display receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G40-7 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G40-4 (+B1) - G40-7 (GND1)*1 Always 11 to 14 V
G40-4 (+B1) - G40-7 (GND1)*2 Always 10.5 to 16 V
G40-3 (ACC1) - G40-7 (GND1)*1 Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V
G40-3 (ACC1) - G40-7 (GND1)*2 Ignition switch ACC 10.5 to 16 V
Ignition switch off Below 1 V
G37-1 (IG) - G40-7 (GND1) Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V


*1: w/o Stop and Start System

*2: w/ Stop and Start System



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR