Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT DOOR BELT MOULDING › from 2016.03
RM3250E _59 Vehicle Exterior _038080 EXTERIOR PANELS / TRIM _0184366 FRONT DOOR BELT MOULDING A

EXTERIOR PANELS / TRIM  FRONT DOOR BELT MOULDING  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the front door belt moulding assembly removal/installation are shown below.

Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system (Click here)
Memorize steering angle neutral point Pre-crash safety system (Click here)

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.

·

Use the same procedure for RHD and LHD vehicles.

·

The procedures listed below are for LHD vehicles.

·

Fully open the front door glass sub-assembly LH before proceeding with work.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
w/ Curtain Shield Airbag:
B394719

Be sure to read Precaution thoroughly before servicing.

for Type B:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION

for Type C:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type C)>PRECAUTION


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
w/ Curtain Shield Airbag:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 67492A 3.REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH

Hide 74220 4.REMOVE FRONT ARMREST ASSEMBLY LH

Hide 5.REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side, w/ Power Window)

Hide 6.REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side, w/ Power Window)

Hide 69260 7.REMOVE FRONT DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)

Hide 69284C 8.REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG LH

Hide 67602 9.REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

Hide 87940 10.REMOVE OUTER REAR VIEW MIRROR ASSEMBLY LH

Hide 67832 11.REMOVE FRONT DOOR SERVICE HOLE COVER LH

Hide 68151C 12.REMOVE FRONT DOOR GLASS RUN LH

Hide 68102 13.REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH

Hide 75720 14.REMOVE FRONT DOOR BELT MOULDING ASSEMBLY LH

a.
B399260C02
0.135,2.677 0.448,2.875 0.313,0.198 12 false *B 0.104,0.104 0.417,0.302 0.313,0.198 12 false *A
*A except Double Cab
*B for Double Cab
V100155

Protective Tape


Put protective tape around the front door belt moulding assembly LH.


b.
B399261C03
0.104,0.104 0.417,0.302 0.313,0.198 12 false *A 0.135,2.635 0.448,2.833 0.313,0.198 12 false *B
*A except Double Cab
*B for Double Cab
V113147

Remove in this Direction


Using moulding remover D, detach the claw and remove the front door belt moulding assembly LH as shown in the illustration.