Home › Power Source / Network › POWER DISTRIBUTION › MAIN BODY ECU(for LHD) › from 2016.03
RM3250E _57 Power Source / Network _038062 POWER DISTRIBUTION _0186317 MAIN BODY ECU(for LHD) A

POWER DISTRIBUTION  MAIN BODY ECU(for LHD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the body ECU removal/installation are shown below.

Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system (Click here)
Memorize steering angle neutral point Pre-crash safety system (Click here)
Body ECU Initialize automatic light control system Automatic light control system (Click here)

PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B394719

Be sure to read Precaution thoroughly before servicing.

for Type A:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION

for Type B:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type A)>PRECAUTION

for Type C:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type C)>PRECAUTION


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 55606 3.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 45287 4.REMOVE LOWER STEERING COLUMN COVER

Hide 73900 5.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

Hide 82730 6.REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

a.
E320327

Disconnect the front side of the 9 connectors.


b.

Detach the 2 wire harness clamps.


c.
E320328

Remove the 2 nuts and instrument panel junction block assembly.


d.
E320329

Disconnect the back side of the 8 connectors.


Hide 7.REMOVE WIRE HARNESS CLAMP BRACKET

a.
E320330

Remove the bolt and wire harness clamp bracket.


Hide 89221B 8.REMOVE BODY ECU

a.
E317114C01
0,0 0,0 false
V113147

Press in this Direction


Press the 2 levers of the body ECU to release the lock.


b.
E317115C01
0,0 0,0 false
V113147

Insert in this Direction
V113148

Raise in this Direction
V100155

Protective Tape


With the body ECU released, insert a screwdriver with its tip wrapped with protective tape horizontally between the body ECU and junction block.

NOTICE:
·

Use a screwdriver with a diameter between 5.0 mm (0.197 in.) and 6.3 mm (0.248 in.) and a length of approximately 90 mm (3.54 in.).

·

Do not insert the screwdriver under the connector socket of the body ECU.




c.
E317116C01
0,0 0,0 false
V113147

Press in this Direction
V113148

Remove in this Direction.


Press the 2 levers of the body ECU again and pull up the body ECU to remove it.

NOTICE:

Do not touch the ECU connector.