Home › Engine / Hybrid System › CRUISE CONTROL › ROAD SIGN ASSIST SYSTEM › from 2016.03
RM3250E _51 Engine / Hybrid System _037980 CRUISE CONTROL _0262561 ROAD SIGN ASSIST SYSTEM U

CRUISE CONTROL  ROAD SIGN ASSIST SYSTEM  TERMINALS OF ECU  


CHECK FORWARD RECOGNITION CAMERA


NOTICE:
·

DTCs may be stored when connectors are disconnected during inspection. Therefore, be sure to clear the DTCs using the GTS once the inspection has been completed.

·

Do not apply excessive force to the Q4 forward recognition camera connector.



a.

Disconnect the Q4 forward recognition camera connector.

C356786E03
2.25,0.76 2.667,1 0.417,0.24 2.375,0.802 2.688,1 0.313,0.198 10 false Q4


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
Q4-7 (IGB) - Body ground V - Body ground Power source Ignition switch ON 11 to 14 V*1
10.5 to 16 V*2
Ignition switch off Below 1 V
Q4-10 (GND) - Body ground B - Body ground Ground Always Below 1 Ω

*1: w/o Stop and Start System

*2: w/ Stop and Start System


HINT:

If the result is not as specified, there may be a malfunction on the wire harness side.



c.

Reconnect the Q4 forward recognition camera connector.

E256359C15
1.708,0.729 2.146,0.979 0.438,0.25 1.833,0.781 2.292,0.979 0.458,0.198 10 false Q4 0.115,0.104 0.427,0.302 0.313,0.198 10 false *a
*a Component with harness connected
(Forward Recognition Camera)
- -



d.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
Q4-5 (CA1P) - Q4-10 (GND) B - B CAN communication signal Ignition switch ON Pulse generation
(See waveform 1)
Q4-11 (CA1N) - Q4-10 (GND) V - B CAN communication signal Ignition switch ON Pulse generation
(See waveform 2)
Q4-6 (CANH) - Q4-10 (GND) B - B CAN communication signal Ignition switch ON Pulse generation
(See waveform 1)
Q4-12 (CANL) - Q4-10 (GND) BR - B CAN communication signal Ignition switch ON Pulse generation
(See waveform 2)


e.

WAVEFORM 1

i.
A086154E96
2.75,0.125 3.323,0.281 0.573,0.156 10 false 1 V/DIV. 1.354,1.938 2.281,2.094 0.927,0.156 10 false 10 μsec./DIV.

CAN communication signal

Item Content
Tester Connection
·

Q4-5 (CA1P) - Q4-10 (GND)

·

Q4-6 (CANH) - Q4-10 (GND)


Tool Setting 1 V/DIV., 10 μsec./DIV.
Condition Ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.




f.

WAVEFORM 2

i.
A086155E87
2.76,0.229 3.292,0.406 0.531,0.177 10 false 1 V/DIV. 1.375,1.896 2.292,2.073 0.917,0.177 10 false 10 μsec./DIV. 2.99,1.375 3.354,1.708 0.365,0.333 10 true GND

CAN communication signal

Item Content
Tester Connection
·

Q4-11 (CA1N) - Q4-10 (GND)

·

Q4-12 (CANL) - Q4-10 (GND)


Tool Setting 1 V/DIV., 10 μsec./DIV.
Condition Ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.