Use the following procedure to troubleshoot the cruise control system.
*: Use the GTS.
| Proceed to |
|---|
| NEXT |
NEXT
Measure the battery voltage.
11 to 14 V
If the voltage is below 11 V, replace or recharge the battery before proceeding to the next step.
| Proceed to |
|---|
| NEXT |
NEXT
Use the GTS to check if the CAN communication system is functioning normally.
for LHD with Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)>DIAGNOSIS SYSTEM
for RHD with Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)>DIAGNOSIS SYSTEM
for LHD without Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD without Central Gateway ECU)>DIAGNOSIS SYSTEM
for RHD without Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD without Central Gateway ECU)>DIAGNOSIS SYSTEM
| Result | Proceed to |
|---|---|
| CAN communication system DTCs are not output | A |
| CAN communication system DTCs are output | B |
A
B
for LHD with Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)>DIAGNOSIS SYSTEM
for RHD with Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)>DIAGNOSIS SYSTEM
for LHD without Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD without Central Gateway ECU)>DIAGNOSIS SYSTEM
for RHD without Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD without Central Gateway ECU)>DIAGNOSIS SYSTEM
Use the GTS to check if the meter / gauge system is functioning normally.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| Meter / gauge system DTCs are not output | A |
| Meter / gauge system DTCs are output | B |
A
B
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
Use the GTS to check if the brake control system is functioning normally.
w/ Vehicle Stability Control System: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
w/o Vehicle Stability Control System: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| Vehicle stability control system DTCs are output (w/ Vehicle Stability Control System) | B |
| Anti-lock brake system DTCs are output (w/o Vehicle Stability Control System) | C |
A
B
C
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
Check for DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR
Clear the DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR
Recheck for DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
A
B
Refer to Problem Symptoms Table.
Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE
| Result | Proceed to |
|---|---|
| Fault is not listed in Problem Symptoms Table | A |
| Fault is listed in Problem Symptoms Table | B |
A
B
Terminals of ECU
Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL SYSTEM>TERMINALS OF ECU
Data List/Active Test
Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL SYSTEM>DATA LIST / ACTIVE TEST
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT