RM3250E
_V1
General
_038082
SPECIFICATIONS
_0176432
2GD-FTV STARTING
F
SPECIFICATIONS 2GD-FTV STARTING SERVICE DATA
Glow plug
| Tester connection
|
Condition
|
Specified Condition
|
| Glow plug terminal - Body ground
|
20°C (68°F)
|
Approximately 1.0 Ω
|
Starter (for 2.0 kW Type)
| Starter
|
Standard current
|
150A or less at 11.5 V
|
| Starter armature assembly
|
Starter armature assembly
|
0.05 mm (0.00196 in.)
|
| Standard commutator diameter
|
29.0 mm (1.14 in.)
|
| Minimum commutator diameter
|
28.0 mm (1.10 in.)
|
| Standard undercut depth
|
0.7 mm (0.0276 in.)
|
| Minimum undercut depth
|
0.4 mm (0.0157 in.)
|
| Segment - Segment
|
Below 1.0 Ω
|
| Segment - Coil core
|
10 kΩ or higher
|
Starter brush holder assembly
(Brush length)
|
Standard
|
10.4 mm (0.409 in.)
|
| Minimum
|
5.0 mm (0.197 in. )
|
Starter (for 2.0 kW Type)
| Item
|
Tester connection
|
Condition
|
Specified condition
|
| Starter brush holder assembly
|
A-B
C-D
D-E
|
Always
|
Below 1 Ω
|
| Magnet starter switch assembly.
|
Terminal 50 - Terminal C
|
Always
|
Below 1 Ω
|
| Terminal 50 - Switch body
|
Below 2 Ω
|
| Starter armature assembly.
|
Segment - Segment
|
Always
|
Below 1 Ω
|
| Segment - Coil Core
|
10 kΩ or higher
|
Starter (for 2.2 kW Type)
| Starter
|
Standard current
|
120A or less at 11 V
|
STARTER (for 2.7 kW Type)
| Starter assembly
|
No-load characteristics current
|
Standard
|
180A or less at 11 V
|
| Magnet starter switch assembly
|
Terminal 50 - Terminal C
|
Standard resistance
|
Below 1 Ω
|
| Terminal 50 - Switch Body
|
Standard resistance
|
Below 2 Ω
|
| Starter brush holder assembly
|
Spring load
|
Standard
|
26 to 45 N (3 to 5 kgf, 5.8 to 10.1 lbf)
|
| Minimum
|
12 N (1 kgf, 2.7 lbf)
|
| Positive (+) brush holder - Negative(-) brush holder
|
Standard resistance
|
10 kΩ or higher
|
| Brush length
|
Standard
|
20.5 mm (0.814 in.)
|
| Minimum
|
11.0 mm (0.433 in.)
|
| Starter yoke assembly
|
Lead Wire - Brush
|
Standard resistance
|
Below 1 Ω
|
| Starter Yoke Body - Brush
|
Standard resistance
|
10 kΩ or higher
|
| Brush length
|
Standard
|
20.5 mm (0.814 in.)
|
| Minimum
|
11.0 mm (0.433 in.)
|
| Starter armature assembly
|
Segment - Segment
|
Standard resistance
|
Below 1 Ω
|
| Segment - Coil Core
|
Standard resistance
|
10 kΩ or higher
|
| Circle runout
|
Maximum
|
0.05 mm (0.00197 in.)
|
| Commutator diameter
|
Standard
|
36.0 mm (1.42 in.)
|
| Minimum
|
35.0 mm (1.38 in.)
|
| Undercut depth
|
Standard
|
0.7 mm (0.0276 in.)
|
| Minimum
|
0.2 mm (0.00787 in.)
|
Starter (w/ Stop And Start System)
| Starter
|
Current criteria
|
160 A or less at 11 V
|
Starter (for BOSCH Made)
| Starter
|
Standard current
|
123A or less at 10.9 V
|
Engine switch
| Tester connection
|
Condition
|
Specified condition
|
5 (SS1) - 6(AGND)
1 (SS2) - 6(AGND)
|
Not pushed
|
10 kΩ or higher
|
5 (SS1) - 6(AGND)
1 (SS2) - 6(AGND)
|
Pushed
|
Below 1 Ω
|
Ignition switch assembly.
| Tester connection
|
Condition
|
Specified condition
|
| -
|
Lock
|
10 kΩ or higher
|
| 7 (ACC) - 5 (AM1)
|
ACC
|
Below 1 Ω
|
8 (IG1) - 5 (AM1)
7 (ACC) - 5 (AM1)
4 (AM2) - 3 (IG2)
|
ON
|
Below 1 Ω
|
8 (IG1) - 5 (AM1)
6 (ST1) - 5 (AM1)
4 (AM2) - 3 (IG2)
4 (AM2) - 2 (ST2)
|
START
|
Below 1 Ω
|
Starter relay assembly (ST NO. 1)
| Tester connection
|
Condition
|
Specified condition
|
| 3 - 5
|
Battery voltage not applied to terminals 1 and 2
|
10 kΩ or higher
|
| Battery voltage applied to terminals 1 and 2
|
Below 1 Ω
|
Starter relay assembly (ST NO. 2)
| Tester connection
|
Condition
|
Specified condition
|
| 3 - 5
|
Battery voltage not applied to terminals 1 and 2
|
10 kΩ or higher
|
| Battery voltage applied to terminals 1 and 2
|
Below 1 Ω
|
Glow relay (GLOW)
| Tester connection
|
Condition
|
Specified condition
|
| 3 - 5
|
Battery voltage not applied to terminals 1 and 2
|
10 kΩ or higher
|
| Battery voltage applied to terminals 1 and 2
|
Below 1 Ω
|