Home › Engine / Hybrid System › 2GD-FTV INTAKE / EXHAUST › INTAKE MANIFOLD › 2016.03–2016.08
RM3250E _51 Engine / Hybrid System _038009 2GD-FTV INTAKE / EXHAUST _0191565 INTAKE MANIFOLD A

2GD-FTV INTAKE / EXHAUST  INTAKE MANIFOLD  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the injector assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Battery terminal is disconnected/reconnected Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system (Click here)
Memorize steering angle neutral point Pre-crash safety system (Click here)

NOTICE:
·

When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.

Replaced Parts (A) Pipes Requiring New Replacement
·

Injector assembly (including shuffling the injector assemblies between the cylinders)

·

Common rail assembly

·

Cylinder head sub-assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly


·

Supply pump assembly

·

Common rail assembly

·

Cylinder block sub-assembly

·

Cylinder head sub-assembly

·

Cylinder head gasket

·

Timing chain case assembly


Fuel inlet pipe sub-assembly

·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly, clean them with a brush and compressed air.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

(Click here General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION)


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

(Click here General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION)


Hide 25800 3.REMOVE EGR COOLER SUB-ASSEMBLY AND NO. 2 EGR VALVE ASSEMBLY WITH ELECTRIC EGR CONTROL VALVE ASSEMBLY

Hide 11409 4.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

a.
A345096

Remove the engine oil level dipstick.


b.

Disconnect the vacuum hose from the intake manifold.


c.

Remove the bolt and engine oil level dipstick guide.


d.

Remove the O-ring from the engine oil level dipstick guide.


Hide 23812D 5.DISCONNECT NO. 2 FUEL PIPE

a.
A345097

Remove the bolt and disconnect the No. 2 fuel pipe.


Hide 6.REMOVE WIRING HARNESS CLAMP BRACKET

a.
A345121

Disconnect the diesel throttle body assembly connector and pre-stroke control valve connector.


b.
A345122

Detach the 2 wire harness clamps.


c.

Remove the bolt and wiring harness clamp bracket.


Hide 17118 7.REMOVE MANIFOLD STAY

a.
A345098

Remove the bolt and disconnect the wiring harness clamp bracket from the intake manifold stay.


b.
A345099

Remove the 2 bolts and manifold stay.


Hide 23804D 8.REMOVE NO. 4 FUEL PIPE SUB-ASSEMBLY (w/ DPF)

a.
A356214C02
0,0 0,0 false
V100136

Union Bolt
V100137

Bolt


Disconnect the No. 4 fuel pipe sub-assembly from the No. 1 fuel pipe.

Click hereEngine / Hybrid System>2GD-FTV FUEL>FUEL SYSTEM>PRECAUTION


b.

Remove the bolt from the intake manifold.


c.

Remove the 2 union bolts and 2 gaskets from the supply pump assembly and fuel filter.


Hide 23815D 9.REMOVE NO. 3 FUEL PIPE (w/ Pressurized Fuel Filter)

a.
A352782C01
0,0 0,0 false
V100135

Union Bolt
V100136

Supply Pump Hollow Screw


Remove the union bolts, supply pump hollow screw and 2 gaskets from the supply pump assembly and fuel filter.


b.

Remove the 2 fuel pipe clamps from the No. 3 fuel pipe and fuel filter.


Hide 23804C 10.REMOVE FUEL INLET PIPE SUB-ASSEMBLY

a.
A345100C01
0.073,0.063 0.385,0.219 0.313,0.156 10 true *a 0.156,2.563 0.469,2.719 0.313,0.156 10 true *b
*a Common Rail Assembly Side
*b Fuel Supply Pump Assembly Side


Remove the 2 bolts, No. 1 injection pipe clamp and No. 2 injection pipe clamp.


b.
A352804E01
0.688,0.781 0.896,0.781 0.896,0.781 1.479,1.667 true 0.323,0.708 0.771,0.979 0.448,0.271 10 true SST

Using SST, loosen the fuel inlet pipe sub-assembly union nut of the common rail assembly side.

NOTICE:

If the No. 1 or No. 2 injection pipe clamp is removed from the inlet pipe sub-assembly, replace the No. 1 or No. 2 injection clamp with a new one.



c.

Using a 19 mm union nut wrench, loosen the inlet pipe sub-assembly union nut of the fuel supply pump assembly side.


Hide 23770 11.REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY

a.
A345101

Slide the clamps and remove the No. 4 fuel hose from the No. 2 nozzle leakage pipe assembly and common rail assembly.


b.

Slide the 2 clamps and remove the No. 5 fuel hose from the No. 1 nozzle leakage pipe assembly and No. 2 nozzle leakage pipe assembly.


c.
A345102

Slide the clamp and disconnect the No. 6 fuel hose from the No. 3 nozzle leakage pipe assembly.


d.

Remove the 2 bolts and No. 2 nozzle leakage pipe assembly.


Hide 17111 12.REMOVE INTAKE MANIFOLD

a.
A345103

Remove the bolt and disconnect the wire harness bracket.


b.
A345104

Disconnect the vacuum hose from the vacuum transmitting pipe sub-assembly.


c.
A345105C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the 7 bolts, 2 nuts, intake manifold and gasket.