Home › Power Source / Network › 2GD-FTV BATTERY / CHARGING › GENERATOR(for 130 A Type) › from 2016.03
RM3250E _57 Power Source / Network _038059 2GD-FTV BATTERY / CHARGING _0263595 GENERATOR(for 130 A Type) A

2GD-FTV BATTERY / CHARGING  GENERATOR(for 130 A Type)  DISASSEMBLY  


PROCEDURE

Hide 27415 1.REMOVE GENERATOR PULLEY WITH CLUTCH

a.

Mount the generator assembly in the vise between aluminum plates.


b.
A341798C01
1.906,0.177 2.031,0.177 2.031,0.177 3.052,0.74 true 1.25,1.104 1.958,1.865 1.958,1.865 2.094,1.865 true 1.792,0.938 2.021,0.177 true 2.281,1.458 2.281,0.833 true 2.208,1.448 2.521,1.604 0.313,0.156 10 false *a 2.156,1.792 2.927,1.99 0.771,0.198 10 false SST B 1.479,0.104 2.25,0.302 0.771,0.198 10 false SST A
*a Gnerator Rotor Shaft


Install SST A and B to the generator pulley with clutch as shown in the illustration.

SST
09820-63021  

NOTICE:

Securely attach SST to the generator pulley with clutch and generator rotor shaft.



c.
A341799C01
1.948,0.531 2.26,0.208 2.26,0.208 2.375,0.208 true 2.156,0.729 2.531,0.49 2.531,0.49 2.656,0.49 true 1.896,1.875 2.208,2.031 0.313,0.156 10 false *a 2.708,0.417 3.25,0.615 0.542,0.198 10 false SST A 2.438,0.125 3.208,0.323 0.771,0.198 10 false SST B
*a Hold
V100135

Turn


Using a wrench to hold SST A, and turn SST B counterclockwise to loosen the generator pulley with clutch.

NOTICE:

Be careful as the generator pulley with clutch or generator rotor shaft may be damaged if the position of SST is not securely maintained while performing this operation.



d.

Remove SST from the generator assembly.


e.

Remove the generator pulley with clutch from the generator rotor shaft.


f.

Remove the generator assembly from the vise.


Hide 27039 2.REMOVE GENERATOR REAR END COVER

a.

Place the generator assembly on the generator pulley with clutch.


b.
A341801

Remove the 3 bolts and generator rear end cover from the generator coil assembly.


Hide 27387 3.REMOVE GENERATOR TERMINAL INSULATOR

a.
A341803

Remove the terminal insulator from the generator coil assembly.


Hide 27370 4.REMOVE GENERATOR BRUSH HOLDER ASSEMBLY

a.
A341805

Remove the 2 screws and generator brush holder assembly from the generator coil assembly.


Hide 27360 5.REMOVE GENERATOR COIL ASSEMBLY

a.
A341807

Remove the 4 through bolts.


b.
A341808C01
0.542,1.594 1.135,1.99 1.135,1.99 1.292,1.99 true 1.99,0.969 2.458,0.792 2.458,0.792 2.635,0.792 true 0.573,0.573 0.885,0.729 0.313,0.156 10 false *a 1.323,1.896 1.781,2.094 0.458,0.198 10 false SST 2.677,0.708 3.135,0.906 0.458,0.198 10 false SST
*a Hold
V100135

Turn


Using SST, remove the generator coil assembly.

SST
09950-40011  (09951-04020, 09952-04010, 09953-04020, 09954-04010, 09955-04071, 09957-04010, 09958-04011)


Hide 27444 6.INSTALL GENERATOR BEARING COVER PACKING

a.
A341809

Remove the generator bearing cover packing.

NOTICE:

If the generator bearing cover packing breaks, remove all broken pieces.


HINT:

The generator bearing cover packing may be installed on the generator rotor assembly.



Hide 27330 7.REMOVE GENERATOR ROTOR ASSEMBLY

a.

Remove the generator rotor assembly from the generator drive end frame.


Hide 27310B 8.INSPECT GENERATOR DRIVE END FRAME BEARING

a.
A341813

Check that the generator drive end frame bearing is not rough or worn and that it rotates smoothly.

If necessary, replace the generator drive end frame bearing.


Hide 27310B 9.REMOVE GENERATOR DRIVE END FRAME BEARING

a.
A341815

Remove the 4 screws and retainer plate from the generator drive end frame.


b.
A341817N01
2.51,0.979 2,0.375 2,0.375 2.625,0.646 true 1.719,0.292 2.177,0.49 0.458,0.198 10 false SST

Using SST and a hammer, tap out the generator drive end frame bearing from drive end frame.

SST
09950-60010  (09951-00250)
09950-70010  (09951-07100)