Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING(for Single Cab) › from 2016.03
RM3250E _58 Vehicle Interior _037970 INTERIOR PANELS / TRIM _0189530 ROOF HEADLINING(for Single Cab) A

INTERIOR PANELS / TRIM  ROOF HEADLINING(for Single Cab)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

A bolt without a torque specification is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS



PROCEDURE

Hide 66424 1.INSTALL REAR SIDE RAIL SPACER LH (w/o Curtain Shield Airbag)

a.
B404493

Attach the claw to install the rear side rail spacer LH.


Hide 66414A 2.INSTALL REAR SIDE RAIL SPACER RH (w/o Curtain Shield Airbag)

a.
B404494

Attach the claw to install the rear side rail spacer RH.


Hide 66423 3.INSTALL FRONT SIDE RAIL SPACER LH (w/o Curtain Shield Airbag)

a.
B404491

Attach the claw to install the front side rail spacer LH.


Hide 66413B 4.INSTALL FRONT SIDE RAIL SPACER RH (w/o Curtain Shield Airbag)

a.
B404492

Attach the claw to install the front side rail spacer RH.


Hide 63310 5.INSTALL ROOF HEADLINING ASSEMBLY

a.

w/ Overhead Console:

i.
B415041C01
0,0 0,0 false
V113147

Movement Direction


Insert the roof headlining assembly into the cabin from the front door.

NOTICE:
·

Check that the corners of the roof headlining assembly are not folded, twisted or otherwise deformed and that none of the mounted parts have fallen off.

·

Make sure that the roof headlining assembly does not get caught on anything as it may become bent or damaged.

·

Do not damage the roof headlining assembly or vehicle interior.




ii.
B409952

Install the visor holder as shown in the illustration.


iii.
B409953C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw to install the visor holder as shown in the illustration.

HINT:

Use the same procedure for both visor holders.



iv.
B404488

Install the roof headlining assembly with the 3 clips.



b.

w/o Overhead Console:

i.
B415039C01
0,0 0,0 false
V113147

Movement Direction


Insert the roof headlining assembly into the cabin from the front door.

NOTICE:
·

Check that the corners of the roof headlining assembly are not folded, twisted or otherwise deformed and that none of the mounted parts have fallen off.

·

Make sure that the roof headlining assembly does not get caught on anything as it may become bent or damaged.

·

Do not damage the roof headlining assembly or vehicle interior.




ii.
B409952

Install the visor holder as shown in the illustration.


iii.
B409953C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw to install the visor holder as shown in the illustration.

HINT:

Use the same procedure for both visor holders.



iv.
B414208

Install the roof headlining assembly with the 3 clips.



c.
B404485C01
1.5,1.781 1.813,1.938 0.313,0.156 10 false *1
*1 Front Door Opening Trim Weatherstrip LH


Connect the front door opening trim weatherstrip LH in the range shown in the illustration.


d.
B404486C01
1.667,1.771 1.979,1.927 0.313,0.156 10 false *1
*1 Front Door Opening Trim Weatherstrip RH


Connect the front door opening trim weatherstrip RH in the range shown in the illustration.


e.

w/ Pre-crash Safety System:

i.
B443926

Connect the connector.



f.

w/o Pre-crash Safety System:

i.
B404484

Connect the connector and attach the clamp to the front pillar LH.



g.

w/ Pre-crash Safety System:

i.
B443959

Connect the connector and attach the clamp to the front pillar LH.



Hide 63339A 6.INSTALL ROOF HEADLINING SERVICE HOLE COVER (w/o Assist Grip)

a.
B410866

Install the 2 roof headlining service hole covers.


Hide 74610A 7.INSTALL ASSIST GRIP SUB-ASSEMBLY

HINT:

w/ Assist Grip:

Use the same procedure for both assist grip sub-assemblies.


a.
B404483

Install the assist grip sub-assembly with the 2 bolts.


b.
B404481

Attach the claw to close the assist grip cover.


Hide 74320 8.INSTALL VISOR ASSEMBLY LH

a.
B404637

Install the visor assembly LH with the 2 screws.


b.

Connect the visor assembly LH to the visor holder.


Hide 74310 9.INSTALL VISOR ASSEMBLY RH

a.
B404638

Install the visor assembly RH with the 2 screws.


b.

Connect the visor assembly RH to the visor holder.


Hide 74325 10.INSTALL VISOR BRACKET COVER LH

a.
B400165C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw to install the visor bracket cover LH as shown in the illustration.


Hide 74325 11.INSTALL VISOR BRACKET COVER RH

a.
B400116C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw to install the visor bracket cover RH as shown in the illustration.


Hide 86466D 12.INSTALL NO. 1 FORWARD RECOGNITION COVER (w/ Pre-crash Safety System)

Hide 81260A 13.INSTALL MAP LIGHT ASSEMBLY

Hide 62512 14.INSTALL QUARTER INSIDE TRIM BOARD LH

a.
B404456C01
0,0 0,0 false
V113147

Install in this Direction


Attach the clip to install the quarter inside trim board LH as shown in the illustration.


b.
B404454C01
2.75,1.063 3.063,1.219 0.313,0.156 10 false *1
*1 Front Door Opening Trim Weatherstrip LH


Connect the front door opening trim weatherstrip LH in the range shown in the illustration.


c.
B404464

Connect the front seat outer belt assembly LH with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 62511 15.INSTALL QUARTER INSIDE TRIM BOARD RH

a.
B404467C01
0,0 0,0 false
V113147

Install in this Direction


Attach the clip to install the quarter inside trim board RH as shown in the illustration.


b.
B404465C01
0.354,1.052 0.667,1.208 0.313,0.156 10 false *1
*1 Front Door Opening Trim Weatherstrip RH


Connect the front door opening trim weatherstrip RH in the range shown in the illustration.


c.
B404463

Connect the front seat outer belt assembly RH with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 73178A 16.INSTALL SEAT BELT ANCHOR COVER CAP

HINT:

Use the same procedure for both seat belt anchor cover caps.


a.
B405829C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw to install the seat belt anchor cover cap as shown in the illustration.


Hide 62514A 17.INSTALL LOWER QUARTER TRIM PANEL LH

a.
B404451C01
0,0 0,0 false
V113147

Install in this Direction


Attach the clip and claw to install the lower quarter trim panel LH as shown in the illustration.


b.
B404449

Connect the front seat outer belt assembly LH with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


c.
B404448C01
2.99,1.573 3.302,1.729 0.313,0.156 10 false *1
*1 Front Door Opening Trim Weatherstrip LH


Connect the front door opening trim weatherstrip LH in the range shown in the illustration.


Hide 62513A 18.INSTALL LOWER QUARTER TRIM PANEL RH

a.
B404460C01
0,0 0,0 false
V113147

Install in this Direction


Attach the clip and claw to install the lower quarter trim panel RH as shown in the illustration.


b.
B404458

Connect the front seat outer belt assembly RH with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


c.
B404457C01
0.229,1.583 0.542,1.74 0.313,0.156 10 false *1
*1 Front Door Opening Trim Weatherstrip RH


Connect the front door opening trim weatherstrip RH in the range shown in the illustration.


Hide 64261C 19.INSTALL UPPER BACK PANEL GARNISH

a.
B404447C01
0,0 0,0 false
V113147

Install in this Direction


Attach the clip and claw to install the upper back panel garnish as shown in the illustration.

HINT:

Lower the claw into position to attach it.



Hide 67914B 20.INSTALL FRONT DOOR SCUFF PLATE LH

a.
B404441C01
0,0 0,0 false
V113147

Install in this Direction


Attach the clip and claw to install the front door scuff plate LH as shown in the illustration.


Hide 67913B 21.INSTALL FRONT DOOR SCUFF PLATE RH

a.
B404444C01
0,0 0,0 false
V113147

Install in this Direction


Attach the clip and claw to install the front door scuff plate RH as shown in the illustration.


Hide 62212 22.INSTALL FRONT PILLAR GARNISH LH

Hide 62211 23.INSTALL FRONT PILLAR GARNISH RH

Hide 74610A 24.INSTALL ASSIST GRIP SUB-ASSEMBLY (w/ Assist Grip)

Hide 25.INSTALL FRONT SEAT ASSEMBLY LH

Hide 27.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (w/ Airbag System)

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION