Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › from 2016.03
RM3250E _58 Vehicle Interior _053993 PRE-CRASH SAFETY _0264409 PRE-CRASH SAFETY SYSTEM U

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  TERMINALS OF ECU  


CHECK MILLIMETER WAVE RADAR SENSOR


E321782E18
2.167,0.75 2.583,1 0.417,0.25 2.26,0.802 2.719,1 0.458,0.198 10 false A64

a.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

If the result is not as specified, there may be a malfunction on the wire harness side.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition

*1: w/o Stop and Start System

*2: w/ Stop and Start System

A64-8 (IGB) - A64-1 (SGND) V - BR Power source Ignition switch ON 11 to 14 V*1
10.5 to 16 V*2
A64-1 (SGND) - Body ground BR - Body ground Ground Always Below 1 Ω


b.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A64-3 (CA2H) - A64-1 (SGND) R - BR CAN communication signal Ignition switch ON Pulse generation
(See waveform 1)
A64-2 (CA2L) - A64-1 (SGND) W - BR CAN communication signal Ignition switch ON Pulse generation
(See waveform 2)
A64-5 (CA1P) - A64-1 (SGND) B - BR CAN communication signal Ignition switch ON Pulse generation
(See waveform 1)
A64-6 (CA1N) - A64-1 (SGND) W - BR CAN communication signal Ignition switch ON Pulse generation
(See waveform 2)


c.

WAVEFORM 1

i.
A086154E97
2.75,0.271 3.365,0.521 0.615,0.25 10 false 1 V/DIV. 1.365,1.906 2.313,2.094 0.948,0.188 10 false 10 μsec./DIV.

CAN communication signal

Item Content
Terminal Name Between A64-3 (CA2H) and A64-1 (SGND)
Between A64-5 (CA1P) and A64-1 (SGND)
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.




d.

WAVEFORM 2

i.
A086155E89
2.76,0.281 3.396,0.51 0.635,0.229 10 false 1 V/DIV. 1.365,1.875 2.333,2.073 0.969,0.198 10 false 10 μsec./DIV.

CAN communication signal

Item Content
Terminal Name Between A64-2 (CA2L) and A64-1 (SGND)
Between A64-6 (CA1N) and A64-1 (SGND)
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.





CHECK FORWARD RECOGNITION CAMERA


E256359E52
1.708,0.729 2.146,0.979 0.438,0.25 1.833,0.781 2.292,0.979 0.458,0.198 10 false Q4

a.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

If the result is not as specified, there may be a malfunction on the wire harness side.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition

*1: w/o Stop and Start System

*2: w/ Stop and Start System

Q4-8 (BZ) - Q4-10 (GND) R - B Skid control buzzer Ignition switch ON, skid control buzzer not operating 11 to 14 V
Ignition switch ON, skid control buzzer operating 0 to 1.5 V
Q4-9 (PBSW) - Q4-10 (GND) P - B Pre-crash system cancel switch assembly Pre-crash system cancel switch assembly being pressed Below 1 Ω
Pre-crash system cancel switch assembly not being pressed 100 kΩ or higher
Q4-7 (IGB) - Q4-10 (GND) V - B Power source Ignition switch ON 11 to 14 V*1
10.5 to 16 V*2
Ignition switch off Below 1 V
Q4-10 (GND) - Body ground B - Body ground Ground Always Below 1 Ω


b.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
Q4-5 (CA1P) - Q4-10 (GND) B - B CAN communication signal Ignition switch ON Pulse generation
(See waveform 1)
Q4-6 (CANH) - Q4-10 (GND) B - B CAN communication signal Ignition switch ON Pulse generation
(See waveform 1)
Q4-11 (CA1N) - Q4-10 (GND) V - B CAN communication signal Ignition switch ON Pulse generation
(See waveform 2)
Q4-12 (CANL) - Q4-10 (GND) BR - B CAN communication signal Ignition switch ON Pulse generation
(See waveform 2)


c.

WAVEFORM 1

i.
A086154E97
2.75,0.271 3.365,0.521 0.615,0.25 10 false 1 V/DIV. 1.365,1.906 2.313,2.094 0.948,0.188 10 false 10 μsec./DIV.

CAN communication signal

Item Content
Terminal Name Between Q4-5 (CA1P) - Q4-10 (GND)
Between Q4-6 (CANH) - Q4-10 (GND)
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.




d.

WAVEFORM 2

i.
A086155E89
2.76,0.281 3.396,0.51 0.635,0.229 10 false 1 V/DIV. 1.365,1.875 2.333,2.073 0.969,0.198 10 false 10 μsec./DIV.

CAN communication signal

Item Content
Terminal Name Between Q4-11 (CA1N) - Q4-10 (GND)
Between Q4-12 (CANL) - Q4-10 (GND)
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.