DATA LIST
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Pre-Crash 2 / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Turn Light RH | Turn signal switch (right) status | ON or OFF | ON: Turn signal switch (right) on
OFF: Turn signal switch (right) off |
- |
| Turn Light LH | Turn signal switch (left) status | ON or OFF | ON: Turn signal switch (left) on
OFF: Turn signal switch (left) off |
- |
| PCS OFF Switch | Pre-crash safety system on/off status | ON or OFF | ON: Pre-crash safety system on
OFF: Pre-crash safety system off |
- |
| PCS Indicator | "Pre-Crash Safety Malfunction Visit Your Dealer" display request signal*1 "PRE-CRASH SAFETY MALFUNCTION VISIT YOUR DEALER" display request signal*2 |
ON or OFF | ON: "Pre-Crash Safety Malfunction Visit Your Dealer" display requested*1 OFF: "Pre-Crash Safety Malfunction Visit Your Dealer" display not requested*1 ON: "PRE-CRASH SAFETY MALFUNCTION VISIT YOUR DEALER" display requested*2 OFF: "PRE-CRASH SAFETY MALFUNCTION VISIT YOUR DEALER" display not requested*2 |
- |
| PCS Disabled Indicator | "Pre-Crash Safety Unavailable" display request signal*1 "PRE-CRASH SAFETY UNAVAILABLE" display request signal*2 |
ON or OFF | ON: "Pre-Crash Safety Unavailable" display requested*1 OFF: "Pre-Crash Safety Unavailable" display not requested*1 ON: "PRE-CRASH SAFETY UNAVAILABLE" display requested*2 OFF: "PRE-CRASH SAFETY UNAVAILABLE" display not requested*2 |
- |
| Pre-Crash Safety Warning Buz | Pre-crash safety system warning buzzer | Valid or Inval | Valid: Pre-crash safety system warning buzzer operation possible
Inval: Pre-crash safety system warning buzzer operation not possible |
- |
| Pre-Crash Brake | Pre-crash brake function | Valid or Inval | Valid: Pre-crash brake operation possible
Inval: Pre-crash brake operation not possible |
- |
| PBA Start | Pre-crash brake assist activation signal | OFF, Standby, Assist Lv1 or Assist Lv2 | OFF: Pre-crash brake assist not operating
Standby: Brake pedal not depressed during pre-crash brake assist operation Assist Lv1: Brake pedal depressed during pre-crash brake assist operation Assist Lv2: Brake pedal firmly depressed during pre-crash brake assist operation |
Signal status changes when the pre-crash brake assist is activated before a crash (Pre-crash brake will activate only in situations where the driver depresses the brake pedal) |
| Brake Assist Standby | - | - | - | This item is displayed on the GTS but is not used. |
| Pre-Crash Brake Control | Pre-crash brake operational status | ON or OFF | ON: Pre-crash brake operating
OFF: Pre-crash brake not operating |
- |
| AVS Start | - | - | - | This item is displayed on the GTS but is not used. |
| VGRS Start | - | - | - | This item is displayed on the GTS but is not used. |
| PBA Control | Pre-crash brake assist operational status | Valid or Invalid | Valid: Pre-crash brake assist control operation possible
Invalid: Pre-crash brake assist control operation not possible |
- |
| Pre-Crash Safety Brake Ind | Pre-crash safety system alarm warning message status | ON or OFF | ON: Displayed
OFF: Not displayed |
"BRAKE!" is displayed |
| PCS Crash Alarm Buzzer | Skid control buzzer status | ON or OFF | ON: Skid control buzzer sounding
OFF: Skid control buzzer not sounding |
- |
| Front Radar-Dirt History | Millimeter wave radar sensor assembly dirt history | ON or OFF | ON: History of excessive dirt
OFF: No history of excessive dirt |
- |
| Front Radar-Environment Hist | Millimeter wave radar sensor assembly environment signal | Good or Bad | Good: Millimeter wave radar sensor assembly environment good
Bad: Millimeter wave radar sensor assembly environment bad |
- |
| Front Radar-Temperature Malfunction History | Millimeter wave radar sensor assembly abnormal temperature history | ON or OFF | ON: History of abnormal temperature
OFF: No history of abnormal temperature |
- |
| Front Radar-Low Voltage History | Millimeter wave radar sensor assembly low voltage history | ON or OFF | ON: History of low voltage
OFF: No history of low voltage |
- |
| Front Recognition Camera-Blockage History | Forward recognition camera obstruction history | ON or OFF | ON: History of being obstructed
OFF: No history of being obstructed |
- |
| Front Recognition Camera-Malfunction History | Forward recognition camera system unavailable history | ON or OFF | ON: History of unavailable
OFF: No history of unavailable |
- |
| Destination Variation No | Destination country for millimeter wave radar sensor assembly | 0 or Not Available | Not Available | - |
| Control Mode | ECU control mode status | Normal or Check Mode | Normal: Normal operation
Check Mode: Operating in Control Mode |
- |
| PCS Operation State Retention Setting | PCS Operation State Retention Setting customize setting | ON or OFF | ON: Customize setting set to ON
OFF: Customize setting set to OFF |
- |
| PCS Alarm Activation Distance Retention Setting 1 | PCS Alarm Activation Distance Retention Setting 1 customize setting | ON or OFF | ON: Customize setting set to ON
OFF: Customize setting set to OFF |
- |
| PCS Alarm Activation Distance Retention Setting 2 | PCS Alarm Activation Distance Retention Setting 2 customize setting | ON or OFF | ON: Customize setting set to ON
OFF: Customize setting set to OFF |
- |
| PCS Alarm Activation Distance Retention Setting 3 | PCS Alarm Activation Distance Retention Setting 3 customize setting | ON or OFF | ON: Customize setting set to ON
OFF: Customize setting set to OFF |
- |
| The Number of DTCs | Number of past trouble codes | min: 0, max: 255 | Number of DTCs will be displayed | - |
*1: for TFT Display Type
*2: for Dot Display Type
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Stop Light Relay Output | Stop light control relay (STOP/CDS FAN Relay) output | ON or OFF | ON: Relay output on (Stop lights on)
OFF: Relay output off (Stop lights off) |
- |
ACTIVE TEST
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Pre-Crash 2 / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| PCS Crash Alarm Buzzer | Skid control buzzer | ON / OFF | Test possible with ignition switch to ON
Vehicle condition: Vehicle stopped |
Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Stop Light Relay | Stop light control relay (STOP/CDS FAN Relay) | Relay ON/OFF | Stop lights come on
Vehicle condition: Vehicle stopped |
Enter the following menus: Body Electrical / Combination Meter / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Indicat. Precrash | PCS warning light | ON / OFF | - |