Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT PROPELLER SHAFT ASSEMBLY(for TMT Made) › from 2016.03
RM3250E _52 Drivetrain _038038 DRIVE SHAFT / PROPELLER SHAFT _0187314 FRONT PROPELLER SHAFT ASSEMBLY(for TMT Made) A

DRIVE SHAFT / PROPELLER SHAFT  FRONT PROPELLER SHAFT ASSEMBLY(for TMT Made)  INSTALLATION  


PROCEDURE

Hide 37140 1.INSTALL FRONT PROPELLER SHAFT ASSEMBLY

NOTICE:

Refer to the components illustration for the installation direction of the propeller shaft.


a.

Completely remove any oil, etc. and clean the contact surfaces of the 2 propeller shaft flanges, differential flange and transfer flange.


b.

Align the matchmarks on the propeller shaft flange and differential flange.


c.

Install the front propeller shaft assembly with the 4 nuts, 4 bolts and 4 washers.

Torque:
88.2 N*m (899 kgf*cm, 65 ft.*lbf)


d.

Align the matchmarks on the propeller shaft flange and transfer flange.


e.

Install the front propeller shaft assembly with the 4 washers and 4 nuts.

Torque:
88.2 N*m (899 kgf*cm, 65 ft.*lbf)


Hide 51561D 2.INSTALL PROPELLER SHAFT GUARD

a.

Install the propeller shaft guard bracket LH.

HINT:

Perform this procedure only when replacement of the propeller shaft guard bracket LH is necessary.


i.
C353992E01
2.042,0.844 2.198,1.042 0.156,0.198 10 true A 1.781,0.625 1.938,0.823 0.156,0.198 10 true A 1.844,0.208 2,0.406 0.156,0.198 10 true B

w/ Urea SCR System:

Install the propeller shaft guard bracket LH with the 2 bolts (A).

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


ii.

w/ Urea SCR System:

Temporarily install bolt (B).


iii.
C353993C01
0.938,0.385 0.854,0.219 0.854,0.219 0.604,0.219 true 1.146,0.229 1.563,0.229 true 0.25,0.125 0.563,0.323 0.313,0.198 10 true *b 1.875,1.927 2.188,2.125 0.313,0.198 10 true *a 1.635,0.135 1.948,0.333 0.313,0.198 10 true *c 0.396,0.51 0.615,0.719 0.219,0.208 10 true B
*a Torque Wrench Fulcrum Length
*b 12 x 14 mm Short Offset Wrench
*c Straight Hexagon Wrench 14


w/ Urea SCR System:

Using a straight hexagon wrench 14 and 12 x 14 mm short offset wrench, tighten bolt (B).

Torque:
Specified tightening torque : 14.3 N*m (146 kgf*cm, 11 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a short offset wrench (fulcrum length of 125.25 mm (4.931 in.)) + torque wrench (fulcrum length of 300 mm (11.811 in.)): 10.1 N*m (103 kgf*cm, 7 ft.*lbf)




iv.
C330831

w/o Urea SCR System:

Install the propeller shaft guard bracket LH with the 2 bolts.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)



b.

Install the propeller shaft guard bracket RH with the 2 bolts.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)

HINT:

Perform this procedure only when replacement of the propeller shaft guard bracket RH is necessary.



c.

Install the front propeller shaft guard with the 2 bolts.

Torque:
36.2 N*m (369 kgf*cm, 27 ft.*lbf)


Hide 51407A 3.INSTALL NO. 3 ENGINE UNDER COVER SUB-ASSEMBLY (w/ Cover)

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)