Home › Drivetrain › AXLE AND DIFFERENTIAL › DIFFERENTIAL SYSTEM(w/ Differential Lock) › from 2016.03
RM3250E _52 Drivetrain _038039 AXLE AND DIFFERENTIAL _0184154 DIFFERENTIAL SYSTEM(w/ Differential Lock) Y

AXLE AND DIFFERENTIAL  DIFFERENTIAL SYSTEM(w/ Differential Lock)  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Use the following procedure listed to troubleshoot the differential system (w/ Differential Lock).

·

*: Use the GTS.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.CUSTOMER PROBLEM ANALYSIS
2.CUSTOMER PROBLEM ANALYSIS
Result:
Proceed to
NEXT



NEXT

3.INSPECT BATTERY VOLTAGE
3.INSPECT BATTERY VOLTAGE
Standard voltage:

11 to 14 V


If the voltage is below 11 V, recharge or replace the battery before proceeding.

Result:
Proceed to
NEXT



NEXT

4.CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*
4.CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*
a.

Use the GTS to check if the CAN communication system is functioning normally.

for LHD without Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD without Central Gateway ECU)>DIAGNOSIS SYSTEM

for RHD without Central Gateway ECU:Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD without Central Gateway ECU)>DIAGNOSIS SYSTEM

for LHD with Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)>DIAGNOSIS SYSTEM

for RHD with Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

HINT:

The ECU of this system is connected to the CAN communication system.

Therefore, before starting troubleshooting, make sure to check that there is no trouble in the CAN communication system.



Result:
Result Proceed to
CAN DTCs are not output A
CAN DTCs are output B



A

5.CHECK DTC AND FREEZE FRAME DATA*

B

5.CHECK DTC AND FREEZE FRAME DATA*
a.

Check for DTCs.

Click hereDrivetrain>AXLE AND DIFFERENTIAL>DIFFERENTIAL SYSTEM(w/ Differential Lock)>DTC CHECK / CLEAR

Powertrain > Four Wheel Drive > Trouble Codes
50001 363

b.

Check for freeze frame data.

HINT:

Record or print DTCs and freeze frame data if necessary.



c.

Clear the DTCs and freeze frame data.

Click hereDrivetrain>AXLE AND DIFFERENTIAL>DIFFERENTIAL SYSTEM(w/ Differential Lock)>DTC CHECK / CLEAR

Powertrain > Four Wheel Drive > Clear DTCs
50002 363

d.

Recheck for DTCs.

Click hereDrivetrain>AXLE AND DIFFERENTIAL>DIFFERENTIAL SYSTEM(w/ Differential Lock)>DTC CHECK / CLEAR

Powertrain > Four Wheel Drive > Trouble Codes
50001 363
i.

Simulate the malfunction condition and check if the DTCs are output again.



Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

6.PROBLEM SYMPTOMS TABLE

B

10.GO TO DTC CHART
6.PROBLEM SYMPTOMS TABLE

Result:
Result Proceed to
Fault not listed in problem symptoms table A
Fault listed in problem symptoms table B



A

7.OVERALL ANALYSIS AND TROUBLESHOOTING*

B

8.REPAIR OR REPLACE
7.OVERALL ANALYSIS AND TROUBLESHOOTING*

NEXT

8.REPAIR OR REPLACE
8.REPAIR OR REPLACE
Result:
Proceed to
NEXT



NEXT

9.CONFIRM TEST
9.CONFIRM TEST
Result:
Proceed to
NEXT



NEXT

END

10.GO TO DTC CHART
Result:
Proceed to
NEXT



NEXT

8.REPAIR OR REPLACE