Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › FRONT SEAT SIDE AIRBAG ASSEMBLY(for Power Seat) › from 2016.03
RM3250E _58 Vehicle Interior _038070 SUPPLEMENTAL RESTRAINT SYSTEMS _0189248 FRONT SEAT SIDE AIRBAG ASSEMBLY(for Power Seat) A

SUPPLEMENTAL RESTRAINT SYSTEMS  FRONT SEAT SIDE AIRBAG ASSEMBLY(for Power Seat)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the front seat airbag assembly removal/installation are shown below.

Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system (Click here)
Memorize steering angle neutral point Pre-crash safety system (Click here)

CAUTION:
·
B394717

Wear protective gloves. Sharp areas on the parts may injure your hands.

·

There is risk of injury.

·

If the front seat side airbag was deployed, replace the front seat airbag assembly, separate type front seatback frame sub-assembly, separate type front seatback cover and separate type front seatback pad with the necessary parts in accordance with the extent of the collision damage.

·

Replace any other damaged parts as necessary.



HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B394719

Be sure to read Precaution thoroughly before servicing.

for Type B:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION

for Type C:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type C)>PRECAUTION


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 71868A 4.REMOVE FRONT SEAT INNER NO. 1 CUSHION SHIELD LH

Hide 71812D 5.REMOVE FRONT SEAT CUSHION SHIELD LH

Hide 71862 6.REMOVE FRONT SEAT INNER CUSHION SHIELD LH

Hide 7.REMOVE SEPARATE TYPE FRONT SEATBACK ASSEMBLY LH

Hide 71759C 8.REMOVE FRONT NO. 1 SEATBACK HOOK

Hide 71931 9.REMOVE FRONT SEAT HEADREST SUPPORT

Hide 10.REMOVE SEATBACK COVER WITH PAD

Hide 73920A 11.REMOVE FRONT SEAT AIRBAG ASSEMBLY LH

CAUTION:
B399378C01
0,0 0,0 false
V100155

Deployment Side


·

When storing the front seat airbag assembly LH, keep the airbag deployment side facing upward.

·

If the airbag deploys for any reason, it may cause a serious accident.



a.
B409668

Detach the wire harness clamp.

NOTICE:

Be careful not to damage the airbag wire harness.



b.

Remove the 2 nuts and front seat airbag assembly LH.

NOTICE:
·

The nuts must not be reused.

·

Make sure that the separate type front seatback frame sub-assembly is not deformed. If it is, replace it with a new one.



B445196C03
0.083,0.031 0.396,0.188 0.313,0.156 12 false *A 3.448,0.042 3.813,0.313 0.365,0.271 12 false *B
*A for Type A *B for Type B