Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW REGULATOR MOTOR(for Front Door) › from 2016.03
RM3250E _59 Vehicle Exterior _038075 WINDOW / GLASS _0185627 POWER WINDOW REGULATOR MOTOR(for Front Door) A

WINDOW / GLASS  POWER WINDOW REGULATOR MOTOR(for Front Door)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the power window regulator motor assembly removal/installation are shown below.

Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system (Click here)
Memorize steering angle neutral point Pre-crash safety system (Click here)

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.

·

Fully open the front door glass sub-assembly LH before proceeding with work.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B394719

Be sure to read Precaution thoroughly before servicing.

for Type A:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type A)>PRECAUTION

for Type B:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION

for Type C:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type C)>PRECAUTION


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 67492A 3.REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH

Hide 74220 4.REMOVE FRONT ARMREST ASSEMBLY LH

Hide 5.REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)

Hide 6.REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)

Hide 69284C 7.REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG LH

Hide 67602 8.REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

Hide 67832 9.REMOVE FRONT DOOR SERVICE HOLE COVER LH

Hide 68151C 10.REMOVE FRONT DOOR GLASS RUN LH

Hide 68102 11.REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH

Hide 69802 12.REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY LH

Hide 85720C 13.REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

a.
B415204

Using a T25 "TORX" socket wrench, remove the 3 screws and power window regulator motor assembly LH.


b.
B415205

for Front Passenger Side, w/o Jam Protection Function:

Using a T25 "TORX" socket wrench, remove the 3 screws and power window regulator motor assembly RH.