Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM(for Type C) › from 2016.03
RM3250E _58 Vehicle Interior _038070 SUPPLEMENTAL RESTRAINT SYSTEMS _0265842 AIRBAG SYSTEM(for Type C) J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(for Type C)  SRS Warning Light Remains ON  


DESCRIPTION

The SRS warning light is located in the combination meter assembly.

When the SRS is normal, the SRS warning light comes on for approximately 6 seconds after the ignition switch is turned from off to ON, and then goes off automatically.

If there is a malfunction in the SRS, the SRS warning light comes on to inform the driver of a problem.

When terminals TC and CG of the DLC3 are connected, DTCs are output by the blinking of the SRS warning light.

The SRS is equipped with a voltage-increase circuit (DC-DC converter) in the airbag sensor assembly in case the source voltage drops.

When the battery voltage drops, the voltage-increase circuit (DC-DC converter) functions to increase the voltage of the SRS to normal voltage.

A malfunction in this circuit is not recorded in the airbag sensor assembly. The SRS warning light automatically goes off when the source voltage returns to normal.

The signal to illuminate the SRS warning light is transmitted from the airbag sensor assembly to the combination meter assembly through the CAN communication system.

WIRING DIAGRAM

C356770E01
2.781,5.781 5.021,6.094 2.24,0.313 10 false Combination Meter Assembly 5.115,5.74 6.792,6 1.677,0.26 10 false Airbag Sensor Assembly 0.615,2.646 1.573,2.917 0.958,0.271 10 false from Battery 1.656,2.792 2.688,3.063 1.031,0.271 10 false ECU-B NO. 1 1.885,1.49 2.51,1.76 0.625,0.271 10 false METER 2.125,0.625 2.719,0.844 0.594,0.219 10 false A/BAG 3.385,3.5 4.333,3.75 0.948,0.25 10 false TELL TALES 3.385,3.917 4.333,4.167 0.948,0.25 10 false LED DRIVER 2.833,4.188 3.229,4.417 0.396,0.229 10 false CPU 3.573,4.5 3.896,4.906 0.323,0.406 10 false CAN I/F 4.063,2.552 4.615,2.792 0.552,0.24 10 false 5 V IC 5.365,4.583 5.979,4.781 0.615,0.198 10 false CANH 5.354,4.958 5.969,5.156 0.615,0.198 10 false CANL 5.365,0.469 5.75,0.688 0.385,0.219 10 false IG2 5.865,3.563 6.25,3.781 0.385,0.219 10 false E1 5.875,4.042 6.26,4.26 0.385,0.219 10 false E2 5.094,0.354 5.385,0.573 0.292,0.219 10 false 21 6.156,3.469 6.448,3.688 0.292,0.219 10 false 25 6.167,3.938 6.458,4.156 0.292,0.219 10 false 26 2.49,1.219 2.781,1.438 0.292,0.219 10 false 22 2.49,2.531 2.781,2.75 0.292,0.219 10 false 21 2.479,2.99 2.771,3.208 0.292,0.219 10 false 27 2.76,2.531 3.146,2.75 0.385,0.219 10 false B 2.76,1.219 3.146,1.438 0.385,0.219 10 false IG+ 2.76,2.99 3.146,3.208 0.385,0.219 10 false EP 2.781,5.604 3.167,5.823 0.385,0.219 10 false G9 5.104,5.563 5.49,5.781 0.385,0.219 10 false G42 0.052,4.844 2.281,5.104 2.229,0.26 10 false *1: w/ Entry and Start System 0.063,5.208 2.292,5.469 2.229,0.26 10 false *2: w/o Entry and Start System 0.771,6.375 2.656,6.625 1.885,0.25 10 false : CAN Communication Line 0.125,0.469 1.354,0.833 1.229,0.365 10 false from IG2 Relay*1 or Ignition Switch*2 0.042,1.875 1.406,2.25 1.365,0.375 10 false from Engine Stop and Start ECU*3 1.656,1.76 1.948,1.979 0.292,0.219 10 false *3 0.063,5.583 2.531,5.844 2.469,0.26 10 false *3: w/ Engine Stop and Start System 0.073,5.948 2.542,6.208 2.469,0.26 10 false *4: w/o Engine Stop and Start System 1.865,0.958 2.156,1.177 0.292,0.219 10 false *4 5.104,4.427 5.396,4.646 0.292,0.219 10 false 13 5.115,4.802 5.406,5.021 0.292,0.219 10 false 22 4.698,4.427 4.99,4.646 0.292,0.219 10 false 36 4.688,4.802 4.979,5.021 0.292,0.219 10 false 35 4.198,4.427 4.813,4.625 0.615,0.198 10 false CANH 4.219,4.792 4.833,4.99 0.615,0.198 10 false CANL

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After replacing the airbag sensor assembly, refer to initialization*.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

When replacing the combination meter assembly, make sure to replace it with a new one.



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM

DTCs are output

DTC is not output

2.CHECK BATTERY
2.CHECK BATTERY
a.

Measure the battery voltage.

Standard voltage:

11 to 14 V


HINT:
·

It may be possible to tell whether the battery is discharged by operating the horn.

·

If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.




Result:
Proceed to
OK
NG



OK

3.CHECK CONNECTION OF CONNECTORS

NG

REPLACE OR RECHARGE BATTERY

3.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the airbag sensor assembly and combination meter assembly.


Result:
Proceed to
The connectors are properly connected
The connectors are not properly connected



The connectors are properly connected

4.CHECK HARNESS AND CONNECTOR (AIRBAG SENSOR ASSEMBLY - BATTERY AND BODY GROUND)

The connectors are not properly connected

CONNECT CONNECTORS PROPERLY

4.CHECK HARNESS AND CONNECTOR (AIRBAG SENSOR ASSEMBLY - BATTERY AND BODY GROUND)
a.
C198548C37
0.385,0.698 0.823,0.99 0.438,0.292 1.594,1.375 1.177,1.844 false 1.719,1.365 2.208,1.896 false 2.219,1.385 2.615,1.385 false 0.469,0.76 0.781,0.917 0.313,0.156 10 false G42 1.094,1.896 1.344,2.083 0.25,0.188 10 false E2 2.156,1.917 2.385,2.083 0.229,0.167 10 false E1 2.646,1.302 2.938,1.469 0.292,0.167 10 false IG2 0.063,0.063 0.281,0.229 0.219,0.167 10 false *a
*a Rear view of wire harness connector
(to Airbag Sensor Assembly)


Disconnect the connectors from the airbag sensor assembly.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Operate all the components of the electrical system (defogger, wipers, headlights, heater blower, etc.).


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G42-21 (IG2) - Body ground Ignition switch ON 11 to 14 V
G42-21 (IG2) - Body ground Ignition switch off Below 1 V



f.

Turn the ignition switch off.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G42-25 (E1) - Body ground Always Below 1 Ω
G42-26 (E2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPLACE HARNESS AND CONNECTOR

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BATTERY AND BODY GROUND)
a.
C253599C26
1.49,0.427 1.875,0.688 0.385,0.26 0.729,1.573 0.896,1.906 true 0.573,1.563 0.427,1.917 true 1.313,1.563 1.479,1.896 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 1.583,0.469 1.896,0.625 0.313,0.156 10 false G9 1.438,1.927 1.667,2.125 0.229,0.198 10 false EP 0.865,1.917 1.177,2.073 0.313,0.156 10 false IG+ 0.375,1.917 0.604,2.083 0.229,0.167 10 false B
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


b.

Disconnect the connector from the combination meter assembly.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G9-22 (IG+) - Body ground Ignition switch ON 11 to 14 V
G9-21 (B) - Body ground Always 11 to 14 V



f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G9-27 (EP) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK SRS WARNING LIGHT (SHORT TO GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK SRS WARNING LIGHT (SHORT TO GROUND)
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Connect the connector to the combination meter assembly.


d.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


e.

Turn the ignition switch to ON.


f.

Check the SRS warning light condition.

OK:

After the primary check period, the SRS warning light goes off for approximately 10 seconds and then remains on.


HINT:

The primary check period is approximately 6 seconds after the ignition switch is turned to ON.



Result:
Proceed to
OK
NG



OK

NG