Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM(for Type C) › from 2016.03
RM3250E _58 Vehicle Interior _038070 SUPPLEMENTAL RESTRAINT SYSTEMS _0265842 AIRBAG SYSTEM(for Type C) J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(for Type C)  Diagnosis Circuit  


DESCRIPTION

DTC output mode is set by connecting terminals TC and CG of the DLC3.

DTCs are output by the blinking of the SRS warning light.

HINT:
·

When each warning light continues blinking, a ground short in the wiring of terminal TC of the DLC3 or an internal ground short in each ECU is suspected.

·

A DTC output mode signal is transmitted through the CAN communication system to each ECU, including the airbag sensor assembly. Thus, when all systems do not enter DTC output mode, there may be an ECM malfunction.



WIRING DIAGRAM

C355581E01
0.531,5.323 2.417,5.573 1.885,0.25 10 false : CAN Communication Line 5.948,4.958 6.875,5.396 0.927,0.438 10 false Airbag Sensor Assembly 5.938,4.771 6.396,4.969 0.458,0.198 10 false G42 1.51,4.365 2.125,4.563 0.615,0.198 10 false DLC3 1.5,4.208 1.958,4.406 0.458,0.198 10 false G8 1.292,3.688 1.646,3.896 0.354,0.208 10 false CG 1.813,3.688 2.167,3.896 0.354,0.208 10 false TC 1.479,2.719 2.094,2.917 0.615,0.198 10 false ECM 1.802,1.802 2.156,2.01 0.354,0.208 10 false TC 2.073,3.573 2.531,3.771 0.458,0.198 10 false 13 1.104,3.583 1.323,3.802 0.219,0.219 10 false 4 2.083,1.698 2.542,1.896 0.458,0.198 10 false 25 1.469,2.552 1.927,2.75 0.458,0.198 10 false G85

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After replacing the airbag sensor assembly, refer to initialization.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM

DTCs are output

DTC is not output

2.CHECK HARNESS AND CONNECTOR (DLC3 - ECM)
2.CHECK HARNESS AND CONNECTOR (DLC3 - ECM)
a.

Turn the ignition switch off.

C355582C01
3.646,0.854 4.021,1.073 0.375,0.219 0.635,0.781 1.01,1 0.375,0.219 2.24,1.063 2.583,1.469 true 5.052,1.094 5.385,1.427 true 0.698,0.813 1.156,1.01 0.458,0.198 10 false G85 3.74,0.885 4.198,1.083 0.458,0.198 10 false G8 5.458,1.375 5.771,1.573 0.313,0.198 10 false TC 2.635,1.406 2.948,1.604 0.313,0.198 10 false TC 1.26,0.094 1.573,0.292 0.313,0.198 10 false *a 4.365,0.188 4.677,0.385 0.313,0.198 10 false *b
*a Front view of wire harness connector
(to ECM)
*b Front view of DLC3



b.

Disconnect the connector from the ECM.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Condition
G85-25 (TC) - G8-13 (TC) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (DLC3 - BODY GROUND)
a.
C198509C27
1.458,0.281 1.844,0.51 0.385,0.229 1.635,0.917 2.094,0.531 2.094,0.531 2.24,0.531 true 0.094,0.125 0.313,0.354 0.219,0.229 10 false *a 2.313,0.458 2.594,0.646 0.281,0.188 10 false CG 1.542,0.323 1.833,0.469 0.292,0.146 10 false G8
*a Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G8-4 (CG) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.
C355583C01
0.292,1 0.688,1.219 0.396,0.219 2.552,1.813 2.104,1.323 true 0.365,1.031 0.823,1.229 0.458,0.198 10 false G85 0.865,0.104 1.177,0.302 0.313,0.198 10 false *a 2.604,1.76 2.917,1.958 0.313,0.198 10 false TC
*a Front view of wire harness connector (to ECM)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G85-25 (TC) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR OR EACH ECU