The front floor side airbag sensor LH or RH consists of a lateral deceleration sensor, etc.
If the airbag sensor assembly receives signals from the lateral deceleration sensor, it determines whether the SRS should be activated.
DTC B162A/2A or B163A/3A is stored when a malfunction is detected in the front floor side airbag sensor LH or RH circuit.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B162A/2A | Side Airbag Sensor Assembly No.2 (RH) | Either condition is met:
·
A front floor side airbag sensor RH malfunction. ·
An airbag sensor assembly malfunction. |
·
Front floor side airbag sensor RH ·
Airbag sensor assembly |
| B163A/3A | Side Airbag Sensor Assembly No.2 (LH) | Either condition is met:
·
A front floor side airbag sensor RH malfunction. ·
An airbag sensor assembly malfunction. |
·
Front floor side airbag sensor LH ·
Airbag sensor assembly |
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
After replacing the airbag sensor assembly, refer to initialization.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
Turn the ignition switch to ON.
Clear the DTCs stored in memory.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type C)>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type C)>DTC CHECK / CLEAR
| Proceed to |
|---|
| DTC B163A/3A is output |
| DTC B162A/2A is output |
| DTC B162A/2A and B163A/3A are not output |
Codes other than DTC B162A/2A and B163A/3A may be output at this time, but they are not related to this check.
DTC B163A/3A is output
DTC B162A/2A is output
DTC B162A/2A and B163A/3A are not output
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type C)>DIAGNOSIS SYSTEM
| *1 | Front Floor Side Airbag Sensor RH |
| *2 | Airbag Sensor Assembly |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Interchange the front floor side airbag sensor LH with RH and connect the connectors to them.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type C)>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type C)>DTC CHECK / CLEAR
| Proceed to |
|---|
| DTC B162A/2A is output |
| DTC B163A/3A is output |
| DTC B162A/2A and B163A/3A are not output |
Codes other than DTC B162A/2A and B163A/3A and B1637/82 may be output at this time, but they are not related to this check.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Return the front floor side airbag sensor RH and LH to their original positions and connect the connectors to them.
DTC B162A/2A is output
DTC B163A/3A is output
DTC B162A/2A and B163A/3A are not output
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type C)>DIAGNOSIS SYSTEM
| *1 | Front Floor Side Airbag Sensor LH |
| *2 | Airbag Sensor Assembly |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Interchange the front floor side airbag sensor RH with LH and connect the connectors to them.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type C)>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type C)>DTC CHECK / CLEAR
| Proceed to |
|---|
| DTC B163A/3A is output |
| DTC B162A/2A is output |
| DTC B162A/2A and B163A/3A are not output |
Codes other than DTC B162A/2A and B163A/3A may be output at this time, but they are not related to this check.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Return the front floor side airbag sensor LH and RH to their original positions and connect the connectors to them.
DTC B163A/3A is output
DTC B162A/2A is output
DTC B162A/2A and B163A/3A are not output
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type C)>DIAGNOSIS SYSTEM